Service bulletins for the 2009 Audi A5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
679 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Electrical system are shown. Show all
| A571402 2022032- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
|---|---|
| A001466 2037949- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. |
| A001465 2011732- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. |
| A641433 2029714- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 64 number 12-22 dated July 5, 2012. After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or parameterized via an SVM specified vs. actual comparison (spec/actual). The parameter data in the software coding container has changed for the front and rear door control units. As a result, an SVM code is required to update the parameter data for any replacement control unit. Simply running an SVM spec/actual will not code nor update the parameter data in the new replacement control unit. A hardware change suggestion will be provided when an SVM spec/actual is executed. An additional hardware replacement is not required. |
| A371423 2028472- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 37 number 12-38 dated February 22, 2012. The ignition key cannot be removed even though the gear shifter is in Park (P). The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. On vehicles with Audi advanced key, the vehicle cannot be locked by remote control after the engine has been switched off. DTC 00230 may be sporadically stored in the vehicle authorization system control module. The Park position of the gear shifter is sporadically not recognized, which causes the ignition key to not be cleared and prevents the vehicle from being locked. |
| Customer Letter | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Audi has determined that, under specific conditions, the turbocharger could malfunction and may cause the Malfunction Indicator Lamp (MIL) on the instrument cluster to illuminate due to the presence of specific fault codes caused by this component. The MIL is part of your on-board diagnostic system. Please refer to your owner's manual for additional information about the MIL. In some locales, an illuminated Malfunction Indicator Lamp could cause your vehicle to fail an IM emissions inspection, and your vehicle registration application could be denied. Please be aware that other conditions (unrelated to the issue described in this letter) may cause the MIL in your vehicle to illuminate. Customers should be prepared to cover all diagnosis and repair costs for these other, unrelated conditions. Dealers will diagnose and replace a faulty turbocharger if necessary, at no cost to you as long as the vehicle remains within the time and mileage limits of this warranty extension. |
| A971443 2036764- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 14-42 dated March 31, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A911437 2030947- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding. |
| A271424 2025360- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly. |
| A171449 2028440- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer. |
| A971442 2036764- | 2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A971441 2036764- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A941432 2017806- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:BACK UP LIGHTS. Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared. |
| A941431 2021751- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 10-19 dated June 7, 2010. The xenon headlight on one side of the vehicle flickers or is inoperative. The condition may be intermittent or permanent. DTCs are stored in the electronic central electronics control module for the affected headlight. Only xenon bulbs manufactured by Philips are affected. The xenon bulb may have an internal leak at the crimp of the electrodes, and xenon gas can be released. Without an adequate amount of xenon gas, the bulb cannot establish a stable light arc. The xenon igniter control unit (ballast) repeatedly tries to establish an arc, which may cause a flickering of the headlight. |
| A911419 2026895- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle. |
| A571400 2027353- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 57 number 11-52 dated August 17, 2011. The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. The key blade can be used to lock or unlock the vehicle mechanically, and the key remote buttons can be used to lock or unlock the vehicle electronically. DTCs may be stored in the access and start authorization control module. |
| A011463 2033630- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 13-86 dated April 15, 2013. The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced. |
| A901342 2035902- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:IGNITION. "Ignition lock faulty" message is displayed in the driver information display with the symbol shown at right. DTCs are stored in the comfort system central control unit. The "ignition lock faulty" message can be triggered by many different DTC entries. Presence of the message does not indicate that the ignition switch is faulty; the message typically has a different root cause. Replacing the ignition switch before completing GFF test plans typically does not correct the condition. |
| Customer Letter | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Audi has determined that a faulty fuel injector may cause minor misfire conditions and, in turn, cause the Malfunction Indicator Lamp (MIL) on the instrument cluster to illuminate due to the presence of specific fault codes caused by this component. In our continuing efforts to assure proper performance of Audi vehicles, your dealer will diagnose and replace a faulty fuel injector, if necessary, at no cost to you as long as the vehicle remains within the time and mileage limits of this warranty extension. Please keep this letter with your Warranty booklet and deliver it to any new owner, along with the owner?s manual. |
| A911304 2013422- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present. |
| A691326 2023323- | 2017-10-31. Service bulletin. AIR BAGS; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model?s SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. |
| A571397 2022032- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
| A271319 2029010- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. |
| A271318 2023282- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed. |
| A911598 2018187- | 2017-10-27. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.