Service bulletin 24L01

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10252422
Published by NHTSA	2024-04-02
Manufacturer's number	24L01
Manufacturer's date	2024-03-20
NHTSA component	FUEL SYSTEM, DIESEL; EQUIPMENT:OTHER:LABELS

NHTSA's summary

Special Field Action 24L01 Certain 2023 Model Year Super Duty F450 - F550 Vehicles Equipped with a 6.7L Diesel Engine - Certified Clean Idle Label Installation

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Equipment and accessories, Fuel system, Labels and manuals

Vehicles listed
FORD F-450 SD	2023 (the catalog's model; the bulletin names a series or trim of it)
FORD F-550 SD	2023 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
2025366	2025-07-08. Fuel System
25V455000	2025-07-07. FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP
23V420000	2023-06-09. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 55031	2026-07-28. Service bulletin. Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
TSB 26-2220	2026-05-14. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Incorrect fuel level displayed in the Ford Pro Telematics Drive App (may show 0% fuel level when the actual level is higher) Incorrect fuel level displayed in the Ford Pro Telematics software (may show 0% fuel level when the actual level is higher) "Unknown" fuel level shown in the Professional Technician System (PTS); connected data may show 0% or Unknown No crank/no start due to a 12V battery drain isolated to the instrument panel cluster (IPC) This may be due to the IPC software. Note: To confirm a F-Super Duty vehicle is built with minor feature code HKRAB, review the build information by double-clicking the vehicle identification number (VIN) in the upper left-hand corner in PTS.
SSM 54317	2025-10-28. Service bulletin. Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2025 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br />Verify the TRM software part number in the vehicle using Ford diagnosis and repair system (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming use causal part 19H332 and labor operation 12651D and 12651D4 of the Service Labor Time Standards (SLTS)
SSM 54215	2025-09-18. Service bulletin. Some 2019-2026 F-Super Duty vehicles equipped with a 6.7L engine may require various repairs and/or maintenance to the fuel system where quick release couplings are utilized, such as the secondary fuel filter. The Workshop Manual (WSM), Section 310-00 > General Procedures > Quick Release Coupling has been updated to include videos and instructions of proper disconnect/connect steps involving the Type 27 quick release couplings.
SSM 52476	2024-05-03. Service bulletin. All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
OTAPU0107VIFXSD	2024-04-04. Service bulletin. Quality Improvements include: - Fixing the headlamp staying ON issue during the BCM OTA update
OTAPU0721WINOTUS	2024-04-04. Service bulletin. Quality Improvements include: - Fix for Window One touch operation
SSM 52328	2024-03-20. Service bulletin. Some 2021-2024 Bronco/F-150, 2023-2024 Escape/F-Super Duty vehicles equipped with SYNC 4 may experience a concern during accessory protocol interface module (APIM) programming where the vehicle's center display screen indicates USB Error. This may be due to a lack of memory space available to perform the APIM software update. If it is a memory concern, the Ford Diagnosis and Repair System (FDRS) will provide an option to delete the voice application. Re-enter the module programming and when prompted, do not select first option - SYNC Module (APIM) Software Update, select the second option - Delete Voice Application(s) From Module. Once deleted, run the SYNC Module (APIM) Software Update as directed, this will update the software and automatically reload the voice app. If the voice delete option is not available, continue with normal diagnostics in the Workshop Manual, Section 418.
SSM 52271	2024-02-23. Service bulletin. Some 2023 F-Super Duty vehicles equipped with a 12 inch center display screen and driver assistance package DBCAY (minor feature code) may exhibit the brakes applying without brake pedal input during parking lot type driving below 5 mph (8 km/h). To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS) OASIS report. This may be due to the Front Brake Assist feature of the vehicle. If the customer finds this feature too sensitive, it can be turned off in the vehicle's center display screen in the Features > Driver Assistance menu. This feature is unrelated to the Pre-Collision Assist feature of the vehicle. To disable the pop-up message that Front Brake Assist is off every time the vehicle is restarted and permanently disable the feature, download and perform the IPMA - Image Processing Module A (IPMA) Configuration application using the latest version of the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use caus
TSB 23-2386	2024-01-05. Service bulletin. Some 2023 F-Super Duty vehicles equipped with a 12.3 inch instrument cluster display screen may exhibit various concerns with the instrument panel cluster (IPC). This may be due to the software in the IPC. To correct the condition, follow the Service Procedure to reprogram the IPC.