WenmarOpen by Wenmar Pro

Service bulletin NTB13037

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10192156
Published by NHTSA2021-05-10
Manufacturer's numberNTB13037
Manufacturer's date2013-04-03
NHTSA componentSTEERING; AIR BAGS; SEAT BELTS

NHTSA's summary

INTRODUCTION Nissan is conducting a Voluntary Safety Recall Campaign to remove the foam damper from the steering column lock on certain specific 2013 model year Titan and 2013 model year NV vehicles. The foam dampener may interfere with the brake shift interlock operation. Removing the foam damper will prevent this issue from occurring. Please see this bulletin for further details.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Air bags, Seat belts, Steering

Vehicles listed
NISSAN NV2013
NISSAN TITAN2013

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20201362020-03-31. Airbag
20V1880002020-03-30. AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
NTB08-097L2023-10-06. Service bulletin. DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB08-097K2023-03-07. Service bulletin. DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13106E2021-05-10. Service bulletin. SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.
NTB150602021-05-10. Service bulletin. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
NTB150362021-05-10. Service bulletin. SERVICE INFORMATION The applied vehicles are equipped with automatic door locks that lock all doors when the vehicle speed reaches 15 MPH. There is no instruction in the Owner?s Manual on auto-lock function deactivation. All doors unlock automatically when the ignition is placed in the OFF position (models with Intelligent Key system) or when the key is removed from the ignition switch (models without Intelligent Key system). The auto-unlock function can be deactivated by the driver in accordance with Owner?s Manual Instructions. Please see this bulletin for further details.
NTB12078A2021-05-10. Service bulletin. SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
NTB00042D2021-05-10. Service bulletin. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB08055C2021-05-10. Service bulletin. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB04094A2021-05-10. Service bulletin. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
NTB00033E2021-05-10. Service bulletin. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.