WenmarOpen by Wenmar Pro

Service bulletin TSB 20-2218

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10180338
Published by NHTSA2020-10-01
Manufacturer's numberTSB 20-2218
Manufacturer's date2020-09-09
NHTSA componentSEATS; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT

NHTSA's summary

Some 2019-2020 Ranger Crew Cab vehicles may exhibit excessive latching effort when returning the rear seat backrest assembly to the upright position. This may be due to oversized rear seat backrest bumpers preventing latch to striker engagement. Vehicles built on or before 04-Feb-2019 may also have excessive deadening material inside the rear seat backrest latch. To correct this condition, follow the Service Procedure steps.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Equipment and accessories, Seats

Vehicles listed
FORD RANGER2019, 2020

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
25V6850002025-10-10. EQUIPMENT:ELECTRICAL:ENGINE BLOCK HEATER
23V3790002023-05-26. EQUIPMENT:OTHER:LABELS
20216372021-10-18. Seats And Restraints
20216102021-10-01. Seats And Restraints
21V7650002021-09-30. CHILD SEAT:VEHICLE LATCH ANCHOR; SEATS:MID/REAR ASSEMBLY
20193402019-07-11. Seats And Restraints

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 524762024-05-03. Service bulletin. All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
TSB 23-23072023-11-02. Service bulletin. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.
SAN-Vol1 I12023-08-16. Service bulletin. The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 516872023-06-16. Service bulletin. TSB 22-2428 is missing some labor operations. For any missing labor operations, claim available new model labor operations or m-time. Refer to this article on the repair order. When replacing the CDF cylinder, the current TSB does not require a complete transmission overhaul or cooler and converter flushing. Ford is currently reviewing the TSB. Monitor OASIS for updates.
SSM 514492023-04-05. Service bulletin. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 23-20622023-04-04. Service bulletin. Some 2019-2023 Ranger crew cab vehicles may exhibit excessive latching effort when returning the rear seat backrest assembly to the upright position. This may be due to oversized rear seat backrest bumpers preventing latch to striker engagement. Vehicles built on or before 04-Feb-2019 may also have excessive deadening material inside the rear seat backrest latch. To correct this condition, follow the Service Procedure to replace the rear seat backrest bumpers and adjust the striker position.
SSM 506512022-05-04. Service bulletin. In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
TSB 22-21392022-04-26. Service bulletin. Some 2017-2020 F-150, 2018-2022 Expedition/Navigator/Mustang and 2019-2022 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
SSM 506292022-03-30. Service bulletin. Some 2019-2020 Ranger vehicles built on or before 30-Jul-2020 may experience poor and/or no temperature change when the temperature is adjusted in the climate control system. There may also be a clicking/snapping noise from behind the instrument panel. Diagnostic trouble code (DTC) B1082 and/or B1081 may also be retrieved from the front controls interface module (FCIM). This may be due to an issue with the blend door and its controls. To avoid repeat repairs, replace the air distribution housing/heater assembly (service base part# 18478). Refer to Workshop Manual (WSM), Section 412-00. Do not replace the evaporator core for this condition. The WSM has been updated to reflect this change. Use causal part 18478 and labor operation 19700D33 of the Service Labor Time Standards (SLTS) Manual.
SSM 506032022-03-22. Service bulletin. Some 2019-2022 Ranger vehicles may experience condensation from the climate control system dripping on the driver's side floor and/or the driver's foot. This may be due to improper or poorly wrapped evaporator lines between the interior bulkhead and the climate control assembly case. Using a flashlight and a mirror, inspect the evaporator lines for being exposed or poorly wrapped. The cut ends of the mastic wrap should be on the top of the lines and have complete coverage. If an issue is found, cover the lines by manipulating the existing mastic wrap, or by adding more mastic to better insulate the lines and limit condensation.