Service bulletin NTB18-030
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10139405 |
| Published by NHTSA | 2018-06-04 |
| Manufacturer's number | NTB18-030 |
| Manufacturer's date | 2018-04-03 |
| NHTSA component | STEERING |
NHTSA's summary
2013 ? 2016 SENTRA; OIL RESIDUE FOUND ON STEERING COLUMN IF YOU CONFIRM Oil residue is found on the steering column assembly near the lower shaft assembly connection. ACTION Clean oil drip and residue from the steering column assembly per the SERVICE PROCEDURE on page 2. NOTE: Do NOT replace the Steering Column Assembly for this incident, if it should occur. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Steering
| NISSAN SENTRA | 2013, 2014, 2015, 2016 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| NTB08-097L | 2023-10-06. Service bulletin. DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
|---|---|
| NTB08-097K | 2023-03-07. Service bulletin. DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB13106E | 2021-05-10. Service bulletin. SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail. |
| NTB15060 | 2021-05-10. Service bulletin. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail. |
| NTB14088B | 2021-05-10. Service bulletin. IF YOU CONFIRM: There is a noise (clunking, popping, or bumping) when the steering wheel is turned AND the noise is coming from the top of either front strut assembly. NOTE: The location of the noise can be determined by using Essential Tool J39570 (Chassis Ear), positioning a clamp on each front strut spring, and then turning the steering wheel back and forth. ACTION: Install a spacer in both the left front and right front strut assemblies where shown in this bulletin. - Refer to the Electronic Service Manual (ESM), section FSU- Front Suspension for removal and installation instructions. See this bulletin for further detail. |
| NTB04094A | 2021-05-10. Service bulletin. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail. |
| NTB00033E | 2021-05-10. Service bulletin. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details. |
| NTB18-030a | 2018-08-20. Service bulletin. 2013-2016 SENTRA; OIL RESIDUE FOUND ON STEERING COLUMN This bulletin has been amended. The CLAIMS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin. |