Service bulletin 17B16

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10127428
Published by NHTSA	2018-01-29
Manufacturer's number	17B16
Manufacturer's date	2017-11-07
NHTSA component	ELECTRICAL SYSTEM; EQUIPMENT

NHTSA's summary

Certain 2011 Model Year Fiesta Vehicles - Battery Junction Box Clean and Seal

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Equipment and accessories

Vehicles listed
FORD FIESTA	2011

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
2017274	2017-05-23. Electrical

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 54601	2026-02-27. Service bulletin. Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
SSM 52476	2024-05-03. Service bulletin. All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
14M02 06	2022-12-02. Service bulletin. Certain 2011 through 2015 Model Year Fiesta and 2012 through 2016 Model Year Focus Vehicles Equipped with a DPS6 Automatic Transmission; Transmission Control Module Extended Warranty Coverage REASON FOR THIS SUPPLEMENT Non-Ford Part Usage: • Vehicles that are still covered by the 8 years/80,000-mile Emissions warranty coverage MUST be serviced with a NEW Ford Motor Company TCM. • Vehicles outside of or exceeding the 8 years/80,000-mile coverage are authorized to use a used Ford Motor Company TCM, a refurbished original Ford TCM, or an aftermarket TCM that will successfully complete the required Ford software updates.
16B02M	2021-12-20. Service bulletin. 49 CFR Part 579.5 Monthly Communications - March 2016
SSM 49130	2020-09-02. Service bulletin. Some 2011-2019 Fiesta vehicles may exhibit various concerns following IPC replacement. Symptoms may include: no crank, 'Contact Hotline message', odometer displaying incorrect English or Metric units and/or diagnostic trouble code (DTC) U2101 in multiple modules. If programmable module installation (PMI) has been performed on the replacement IPC, disconnect the IPC, start a new session using the appropriate Ford scan tool and perform a PMI on the IPC. Do not reconnect the IPC until after the scan tool states it is unable to communicate with the IPC, then allow the PMI process to complete. This will automatically load the correct configuration and address any related DTCs or symptoms.
SSM 47563	2018-11-19. Service bulletin. Some 2011-2014 Fiesta and 2012-2014 Focus vehicles equipped with a DPS6 transmission may experience a fluid leak between the engine and transmission. Be aware that the engine oil and DPS6 transmission fluid are similar in color and texture. A transmission fluid leak at the input shaft seal can cause a buildup of fluid in the bell housing; creating the appearance of a rear main seal leak. The rear main seal should only be replaced after a rear main seal failure is confirmed through appropriate diagnostics outlined in the updated online Workshop Manual (WSM) Section 303-00 / Diagnosis and Testing with the use of Fluorescent dye (164-TP33200601).
SSM 47409	2018-09-10. Service bulletin. Some 2011-2018 Fiesta vehicles may exhibit various concerns following IPC replacement. Symptoms may include: no crank, Contact Hotline message, odometer displaying incorrect English or Metric units and/or diagnostic trouble code (DTC) U2101 in multiple modules. If programmable module installation (PMI) has been performed on the replacement IPC, disconnect the IPC, start a new session using the appropriate Ford scan tool and perform a PMI on the IPC. Do not reconnect the IPC until after the scan tool states it is unable to communicate with the IPC, then allow the PMI process to complete. This will automatically load the correct configuration and address any related DTCs or symptoms.
tsb18-2185	2018-09-10. Service bulletin. This article supersedes TSB 18-2024 to update the model years. Some 2011-2018 Fiesta vehicles may exhibit a lack of heat resulting from a frozen blower motor. This may be caused by snow entering through the cowl panel grille and screen assemblies. Snow may melt in the heating, ventilation and air conditioning (HVAC) case allowing water to enter the blower motor and freeze during a below freezing overnight soak. Blower motor fuse F4 in the battery junction box (BJB) may also be open and the cabin air filter may be saturated. Follow the Service Procedure steps to correct the condition.
SSM 47009	2018-06-11. Service bulletin. The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
SSM 47002	2018-06-11. Service bulletin. Some 2011-2017 Fiesta vehicles may exhibit various concerns following IPC replacement including odometer displaying incorrect English or Metric units and/or diagnostic trouble code (DTC) U2101 in multiple modules. If Programmable Module Installation (PMI) has been performed on the replacement IPC, disconnect the IPC, start a new Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) session and perform a PMI on the IPC. Do not reconnect the IPC until after the IDS or FJDS states it is unable to communicate with the IPC, then allow the PMI process to complete. This will automatically load the correct configuration and address any related DTCs or symptoms.