Service bulletin 1800804
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10005979 |
| Published by NHTSA | 2004-04-05 |
| Manufacturer's number | 1800804 |
| Manufacturer's date | 2004-02-24 |
| NHTSA component | ENGINE AND ENGINE COOLING:ENGINE |
NHTSA's summary
LOW IDLE SPEED INDUCED DRONE AND/OR INTERMITTENT PART TIME TRANSFER CASE LAMP. *TT
The document
No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.
Components
Engine
| JEEP GRAND CHEROKEE | 2004 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 9003215 | 2023-01-09. Service bulletin. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine. |
|---|---|
| 05191925A | 2022-12-19. Service bulletin. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please perform the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Remove hex nut and the top flared fitting on the radiator tank.~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.~ 5. Install the top flared fitting by hand, then torque the fitting to 235 +/- 15 Lb-In.~ 6. Install the hex nut and torque to 100 +/- 10 Lb-In.~ 7. Repeat steps 2-6 for bottom flared fitting.~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ |
| 9003215 | 2022-10-17. Service bulletin. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine. |
| R2118796A | 2021-05-03. Service bulletin. Valve Body. These may cause over drive cycling. |
| 05191925A$ | 2020-10-26. Service bulletin. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please perform the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Remove hex nut and the top flared fitting on the radiator tank.~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.~ 5. Install the top flared fitting by hand, then torque the fitting to 235 +/- 15 Lb-In.~ 6. Install the hex nut and torque to 100 +/- 10 Lb-In.~ 7. Repeat steps 2-6 for bottom flared fitting.~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ |
| 05191925A$ | 2017-11-03. Service bulletin. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked. |
| 0900205 | 2005-08-12. Service bulletin. ENGINE OIL WEEPAGE AT THE ENGINE OIL FITLER ADAPTOR HOSE CONNECTION(S). *TT |
| 05002 | 2005-05-18. Service bulletin. NEW WATER PUMP FOR 3.7L ENGINE - NO LONGER COMMON WITH 4.7L. ADVANCED SERVICE INFORMATION #05-002. *TT |
| 0900105 | 2005-04-26. Service bulletin. CYLINDER HEAD BOLT RE-TORQUE PROCEDURE. GPOP - ISSUE REVIEW SYSTEM. *TT |
| 1804504 | 2005-02-07. Service bulletin. WARM ENGINE ROUGH IDLE. 4.7L. *TT |