Transport Canada recall 2023391
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2023391 |
| Manufacturer's number | 6023G |
| Reported | 2023-07-14 |
| Component | Visual System |
| Notification type | Safety TC |
| Units potentially affected | 116779 |
What is wrong
Issue:
On certain vehicles, a problem with the rearview camera connector could cause distortion or flickering of the rearview camera image.
Note: This recall only affects hatchback (5-door) models.
Safety Risk:
A rearview camera image that doesn't display correctly could reduce a driver's ability to see behind the vehicle while backing up. This could increase the risk of a crash.
Corrective Actions:
Mazda will notify owners by mail and advise you to take your vehicle to a dealership to inspect the rearview camera and install a seal for the wiring harness. The dealer will replace the rearview camera, if necessary.
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| SA-039-23a | 2023-10-05. Service bulletin. Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. |
|---|---|
| 09-031-20b | 2023-08-04. Service bulletin. Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally. |
| 09-031/20a | 2023-08-04. Service bulletin. Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Use the link below to view the recall: RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY |
| 00-001-23 | 2023-08-03. Service bulletin. In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an “as-needed” basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced. |
| 09-025-23 | 2023-07-05. Service bulletin. Some customers may complain that the frequency of replenishing the window washer liquid is higher than expected, or they may complain of leakage at or around the washer motor (1). This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section. This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section. |
| SA-012-23 | 2023-04-04. Service bulletin. Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet. |
| SA-010-23 | 2023-03-03. Service bulletin. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection. |
| SA-045-22a | 2023-01-05. Service bulletin. The purpose of this Service Alert is to remind dealers to keep the protective films on the piano black door garnishes attached until just before delivering the vehicle to the customer. The protective films are attached on new vehicles when shipped from the factory in order to avoid being scratched during transportation and while in dealer stock. |
| SA-074-22 | 2022-12-02. Service bulletin. Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified. |
| Monitor | 2022-06-06. Service bulletin. Mazda connect "no signal" message in reverse |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.