Transport Canada recall 2013442
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2013442 |
| Reported | 2013-12-13 |
| Component | Fuel System |
| Notification type | Safety Mfr |
| Units potentially affected | 6325 |
What is wrong
On certain motorcycles, cracks could develop in the fuel pump and/or auxiliary fuel pump flange (if equipped). This would result in fuel leaking when the engine is turned on and the fuel system is pressurized. Leaking fuel, in the presence of an ignition source, could lead to a fire causing injury and/or damage to property. Correction: Dealers will inspect the fuel pump flange(s) and install a reinforcing ring or replace the fuel pump(s), as necessary.
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| MC160214 | 2023-12-06. Service bulletin. BMW Motorrad USA has become aware of a potential durability issue with the film type fuel level sender “Fuel Strip” equipped on certain model year 2005 to 2013 R and K series motorcycles. |
|---|---|
| MC48166137 | 2019-07-15. Service bulletin. Fuel Gauge faulty. |
| 130413 | 2018-12-17. Service bulletin. N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced up to 7/2013 |
| 130612 | 2018-12-03. Service bulletin. "N63 and N74 Engine: ISTA/D 2.33 Diagnostic Error in the Low-pressure Fuel Supply Sensor Value. INFORMATION When diagnosing the low-pressure fuel supply sensor with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar at all times. * B1214_DI6KNDR * D18KHDR * AT1214_DIKNDR * AT1214_DIKHDR Do not replace the low-pressure fuel supply sensor. The operating pressure of the low-pressure fuel supply sensor can found in ""DME Diagnostic Query"" using the following procedure: 1. Exit the test plan and return to the control unit tree. http://www.bmwtis.net/tiscode/cgi-bin/omcgi.exe?sie_path=/tsb/bulletins/htm_store/14907...11/7/2012 Page 2 of 2 2. Select ""DME"" in the control unit tree. 3. Select "" Call Up ECU Functions."" 4. Select ""Diagnostic Query."" 5. Select ""Fuel Pressure (Low Pressure)."" 6. Select ""Query Status."" The engine must be running to verify operation of the pressure sensor. The software error will be corrected in ISTA/D 2.34, scheduled for release in December 2012. " |
| 130712 | 2018-12-03. Service bulletin. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation. |
| 130413 | 2018-12-03. Service bulletin. N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2013 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 It is good practice to verify that the part number being removed from the engine matches the new injector part number, until further notice. When the ETK data is corrected, a notification will be distributed. |
| 121413 | 2018-12-03. Service bulletin. "N63T: Drive Malfunction Message with Rail Pressure Sensor Fault Stored. The Check Control Message ""Drive, drive moderately"" is displayed with any of the following rail pressure sensor faults stored in the DME: 119001 - Rail pressure sensor, electrical: Short circuit to positive 119002 - Rail pressure sensor, electrical: Short circuit to ground 119101 - Rail pressure sensor 2, electrical: Short circuit to positive 119102 - Rail pressure sensor 2, electrical: Short circuit to ground A poor electrical connection between the rail pressure sensor and engine harness due to vibration" |
| MC5382641801 | 2018-12-03. Service bulletin. R1200R has no fuel level or engine temperature display despite having an on-board computer |
| 130712 | 2018-12-03. Service bulletin. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation. |
| 161514 | 2018-11-13. Service bulletin. NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.