NHTSA recall 12V319000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 12V319000 |
| Manufacturer's number | 12S34 |
| Manufacturer | FORD MOTOR COMPANY |
| Reported | 2012-07-06 |
| Owners notified | 2012-07-20 |
| Component | STRUCTURE; SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES |
| Units potentially affected | 8266 |
What is wrong
FORD IS RECALLING CERTAIN MODEL YEAR 2013 ESCAPE VEHICLES MANUFACTURED FROM MARCH 8, 2012 THROUGH JUNE 7, 2012. DUE TO MIS-POSITIONED CARPET PADDING THE CENTER CONSOLE TRIM PANEL MAY BE PUSHED OUTBOARD OF THE INTENDED POSITION, REDUCING CLEARANCE RELATIVE TO THE PEDAL PACKAGE.
What can happen
THE REDUCED CLEARANCE MAY RESULT IN THE DRIVER’S FOOT CONTACTING THE SIDE OF THE BRAKE PEDAL WHILE TRANSFERRING THE FOOT FROM THE ACCELERATOR PEDAL TO THE BRAKE PEDAL, INCREASING STOPPING DISTANCES AND THE RISK OF A CRASH.
The remedy
FORD WILL NOTIFY OWNERS, AND DEALERS WILL REMOVE THE CARPET PADDING AND LEFT-SIDE CONSOLE TRIM PANEL REPLACED WITH A NEW PANEL, FREE OF CHARGE. THE RECALL BEGAN ON JULY 20, 2012. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
Notes
FORD'S RECALL CAMPAIGN NUMBER IS 12S34.CUSTOMERS MAY CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY: 1-800-424-9153); OR GO TO HTTP://WWW.SAFERCAR.GOV.
| 2013 FORD ESCAPE | Built 2012-03-08 to 2012-06-07. |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| SSM 54601 | 2026-02-27. Service bulletin. Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k |
|---|---|
| SSM 51536 | 2023-05-04. Service bulletin. For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN. |
| SSM 51261 | 2023-01-06. Service bulletin. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
| SSM 51181 | 2022-11-29. Service bulletin. Some 2013-2016 Escape/Fusion/MKZ vehicles may display an error message when updating the All Wheel Drive-ATC Barcode using the IDS service function after installing a new rear drive unit assembly (RDU) or active torque coupling (ATC) clutch assembly. To prevent this error from occurring, enter the universal ATC 4 digit barcode 7772. Once programmed, perform several figure 8 turns at parking lot speeds to verify there is no binding from the all wheel drive (AWD) system. If the vehicle binds in a turn, perform Pinpoint Test A. Refer to the Workshop Manual (WSM), Section 308-07A > Diagnosis and Testing. |
| SSM 51120 | 2022-10-11. Service bulletin. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
| TSB160001 | 2021-12-20. Service bulletin. 49 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C |
| LTR3756 | 2021-12-20. Service bulletin. 49 CFR Part 579.5 Monthly Communications - January 2016 |
| SSM 50064 | 2021-09-04. Service bulletin. Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
| TSB 20-2171 | 2020-06-05. Service bulletin. Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement. |
| SSM 47430 | 2018-09-10. Service bulletin. If a trailer hitch receiver is installed on a 2013-2018 Escape or 2015-2019 MKC vehicle equipped with a hands-free liftgate, the hands-free liftgate function will become inoperative. Hands-free liftgate function can be restored by replacing the existing hands-free liftgate actuation upper sensor (14F680), lower sensor (14F680), stone deflector (17779), hands-free liftgate actuation module (14B291), plastic fasteners (N807951S) and screws (W506964) that are required for the factory installed trailer hitch receiver with hands-free liftgate option. Replacement of these parts to restore hands-free liftgate function is not warrantable. Regardless of trailer hitch configuration, the hands-free liftgate system cannot be added to a vehicle that was originally built without the hands-free liftgate option. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.