WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Subaru Impreza

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

530 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Body and frame are shown. Show all

Bulletins, newest first
05-62-18R2026-09-03. Service bulletin. STRUCTURE:BODY. This bulletin provides a procedure to address customer concerns of surface rust accumulating in the top center retaining nut area of the front strut mounts. This is an revised version of the original bulletin.
13-108-252025-09-02. Service bulletin. STRUCTURE:BODY. This bulletin provides information on paint codes for vehicles in the 2026 line up.
12-321-21R2023-09-05. Service bulletin. EQUIPMENT; STRUCTURE. This bulletin announces a design change made to the cowl panel.
12-319-212021-05-05. Service bulletin. STRUCTURE. This bulletin announces design changes made to the front and rear door glass run channels.
12-312-212021-03-04. Service bulletin. EQUIPMENT; STRUCTURE. This bulletin announces availability of new center console armrest covers to address the a wrinkling condition.
12-296-20R2020-12-05. Service bulletin. EQUIPMENT; SUSPENSION; STRUCTURE:FRAME AND MEMBERS; EQUIPMENT ADAPTIVE/MOBILITY. This Service Information Bulletin outlines design changes made to the rear frame section weld nuts and the mounting bolts used to secure the rear stabilizer bar brackets.
12-293-202020-09-04. Service bulletin. STRUCTURE. This bulletin announces design changes made to the rear quarter glass assembly in response to a small number of reports describing a rattling - type sound origination from the lower molding.
12-296-20R2020-08-03. Service bulletin. SUSPENSION; STRUCTURE:FRAME AND MEMBERS. This Service Information Bulletin outlines design changes made to the rear frame section weld nuts and the mounting bolts used to secure the rear stabilizer bar brackets to them.
12-283-202020-04-03. Service bulletin. EQUIPMENT; STRUCTURE. This bulletin announces a design change made to the hood stay support. This change will prevent vibration sounds resulting from contact with adjacent under-hood components.
07-173-202020-04-02. Service bulletin. STRUCTURE:BODY:HATCHBACK/LIFTGATE; ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES. This Service Information Bulletin provides insight on how to address a customer concern of the rear hatch, Power Rear Gate (PRG) or trunk release operating (or finding the PRG/trunk open unexpectedly after parking) without a specific input (button press) from the operator.
12-279-20R2020-04-02. Service bulletin. STRUCTURE:BODY:DOOR; EQUIPMENT ADAPTIVE/MOBILITY. This bulletin announces availability of new outer door handles to address isolated concerns of the chrome finish peeling.
10-89-182018-12-10. Service bulletin. STRUCTURE:FRAME AND MEMBERS. This bulletin provides a procedure and precautions to use when addressing a customer concern of an improper fit or gap condition of the center vent grille assembly as shown in the comparison photos below.
12-252-182018-12-10. Service bulletin. STRUCTURE:FRAME AND MEMBERS; EQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE:BODY. This Service Information bulletin announces a procedure change for installation of the under-body grommets used to seal the tie-down holes used during vehicle transport. Previously, the grommetswere supplied with the vehicle and placed in the glove box to be installed as part of the pre-delivery inspection (PDI) procedure. Recently, all carriers transporting vehicles from SIA began using individual wheel tie-downs instead of the chain-type tie-downs. As a result, these under-body grommets are now installed during vehicle assembly.
10-89-182018-12-10. Service bulletin. STRUCTURE. This bulletin provides a procedure and precautions to use when addressing a customer concern of an improper fit or gap condition of the center vent grille assembly as shown in the comparison photos below.
12-252-182018-12-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE:FRAME AND MEMBERS. This Service Information bulletin announces a procedure change for installation of the under-body grommets used to seal the tie-down holes used during vehicle transport. Previously, the grommetswere supplied with the vehicle and placed in the glove box to be installed as part of the pre-delivery inspection (PDI) procedure. Recently, all carriers transporting vehicles from SIA began using individual wheel tie-downs instead of the chain-type tie-downs. As a result, these under-body grommets are now installed during vehicle assembly.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.