WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Subaru BRZ

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

376 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Body and frame are shown. Show all

Bulletins, newest first
13-108-252025-09-02. Service bulletin. STRUCTURE:BODY. This bulletin provides information on paint codes for vehicles in the 2026 line up.
1214012R2023-05-08. Service bulletin. STRUCTURE:BODY:TRUNK LID; STRUCTURE. ?Clack? or ?Popping? Sound from Trunk
12140122023-04-17. Service bulletin. STRUCTURE:BODY:TRUNK LID. ?Clack? or ?Popping? Sound from Trunk
12-309-212021-03-04. Service bulletin. EQUIPMENT; STRUCTURE. This bulletin announces a design change made to the replacement front console box cover.
12-271-192019-09-05. Service bulletin. STRUCTURE. This Service Information Bulletin announces a design change made to the rear bumper cover side mounting brackets. These new brackets provide increased clearance between the edges of the bumper cover and the corresponding quarter panels. This change will prevent them from contacting each other and possibly damaging their painted surfaces.
12-267-192019-07-22. Service bulletin. STRUCTURE. This bulletin announces availability of a new retaining plate and installation method to address gapping conditions which may develop between the front bumper cover and fender.
12-251-182018-12-10. Service bulletin. LATCHES/LOCKS/LINKAGES; STRUCTURE:BODY. This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just one side instead of in the middle, one may close and not the other. Over time, if the door is not fully closed with both latches, high cabin temperatures along with weight of the items inside the glove box may cause the assembly to deform slightly and a gap to develop.
12-251-182018-12-10. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; STRUCTURE:BODY; STRUCTURE:FRAME AND MEMBERS. This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just one side instead of in the middle, one may close and not the other. Over time, if the door is not fully closed with both latches, high cabin temperatures along with weight of the items inside the glove box may cause the assembly to deform slightly and a gap to develop.
12-250-182018-10-01. Service bulletin. STRUCTURE:BODY:BUMPERS. This bulletin announces a design change made to the rear bumper cover (face). To insure a proper fit of the new cover, the rear edge portion of the existing inner mud guards (splash shields) will need to be modified slightly in specific areas. In addition, plastic arch caps (plugs) are inserted into unused holes in the rear wheel arch lip of the new cover to fill unused mounting holes for optional accessory mud guards when not installed.
12-231-18R2018-06-11. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE. This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to enter the cabin.
12-231-18R2018-06-11. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE; STRUCTURE:FRAME AND MEMBERS. This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to enter the cabin.
12-231-182018-03-13. Service bulletin. STRUCTURE:BODY. ( 2017-2018MY Impreza - 5 Dr Only)
12-200-16R2017-10-27. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Conditions ranging from the accumulation of water and condensation, to insect intrusion and lens / body cracking have all been addressed in previous bulletins. Recently, concerns about a cloudy appearance of the lens have created yet another bulletin. To help better organize these publications, all the related bulletins are being been condensed into this new release putting all the information in one place for easier reference. As listed in their chronological order, design changes and procedures have been developed to address customer concerns of: ? Condition 1: Condensation accumulation- inspection for possible cracking of lamp housing ? Condition 2: Condensation accumulation- flange (retaining) nut change for combination lamp assy. to prevent rear body panel distortion and increased gasket (packing) thickness to improve sealing. ? Condition 3: Trunk lid contacting (and in isolated cases cracking) the combination lamp assy. when closing- change to the trunk stoppers and trunk weatherstrip ? Condition 4: Insect intrusion inside the combination lamps- further revision to the lamp assy. and gasket ? Condition 5: Cloudy appearance of the lens- anti-fog coating applied at production to the inside of combination lamp lens.
12-200-162017-10-27. Service bulletin. ENGINE AND ENGINE COOLING; STRUCTURE. Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Conditions ranging from the accumulation of water and condensation, to insect intrusion and lens / body cracking have all been addressed in previous bulletins. Recently, concerns about a cloudy appearance of the lens have created yet another bulletin. To help better organize these publications, all the related bulletins are being been condensed into this new release putting all the information in one place for easier reference. As listed in their chronological order, design changes and procedures have been developed to address customer concerns of: ? Condition 1: Condensation accumulation- inspection for possible cracking of lamp housing ? Condition 2: Condensation accumulation- flange (retaining) nut change for combination lamp assy. to prevent rear body panel distortion and increased gasket (packing) thickness to improve sealing. ? Condition 3: Trunk lid contacting (and in isolated cases cracking) the combination lamp assy. when closing- change to the trunk stoppers and trunk weatherstrip ? Condition 4: Insect intrusion inside the combination lamps- further revision to the lamp assy. and gasket ? Condition 5: Cloudy appearance of the lens- anti-fog coating applied at production to the inside of combination lamp lens.
12-225-172017-09-14. Service bulletin. STRUCTURE:BODY; STRUCTURE. This bulletin provides a service procedure to address a small number of reports involving water leaking into the interior and collecting in the passenger's front floor area.
12-200-16R2017-08-14. Service bulletin. STRUCTURE; EXTERIOR LIGHTING:BRAKE LIGHTS. Rear Combination Lamp and Related Enhancements - Since the introduction of the BRZ, there have been a number of revisions to the rear combination lamps and their sealing gaskets (a.k.a. packing) to address varying customer concerns. Conditions ranging from the accumulation of water and condensation, to insect intrusion and lens / body cracking have all been addressed in previous bulletins. Recently, concerns about a cloudy appearance of the lens have created yet another bulletin. To help better organize these publications, all the related bulletins are being been condensed into this new release putting all the information in one place for easier reference.
12-162-14R2017-08-14. Service bulletin. EXTERIOR LIGHTING:BRAKE LIGHTS; EXTERIOR LIGHTING:BACK UP LIGHTS; STRUCTURE. Design Change to Rear Combination Lamps to Prevent Insect Intrusion - IMPORTANT NOTE: Due to the number of revisions made and to make the information contained in TSBs 12-131-12R, 12-145-13R, 12-160-13 and 12-162-14 easier to use, these TSBs have been combined into TSB 12-200-16R dated 3/6/2017.
12-145-13R2017-08-14. Service bulletin. EXTERIOR LIGHTING:BRAKE LIGHTS; EXTERIOR LIGHTING:BACK UP LIGHTS; STRUCTURE. Condensation in Rear Combination Lamps, Retaining Nut and Sealing Gasket Change - IMPORTANT NOTE: Due to the number of revisions made and to make the information contained in TSBs 12-131-12R, 12-145-13R, 12-160-13 and 12-162-14 easier to use, these TSBs have been combined into TSB 12-200-16R dated 3/6/2017.
12-131-12R2017-08-14. Service bulletin. STRUCTURE; EXTERIOR LIGHTING:BACK UP LIGHTS; EXTERIOR LIGHTING:BRAKE LIGHTS. Condensation in Rear Combination Lamp - IMPORTANT NOTE: Due to the number of revisions made and to make the information contained in TSBs 12-131-12R, 12-145-13R, 12-160-13 and 12-162-14 easier to use, these TSBs have been combined into TSB 12-200-16R dated 3/6/2017.
07-94-152017-02-16. Service bulletin. STRUCTURE:BODY. THIS BULLETIN PROVIDES A REPAIR PROCEDURE TO ADDRESS CONCERNS OF CONTACT BETWEEN THE TOP HORIZONTAL EDGE OF THE SIDE MARKER LAMP AND THE CORRESPONDING FENDER EDGE AS SHOWN IN THE PHOTO TO THE RIGHT.
07-73-132016-05-23. Service bulletin. STRUCTURE:EMERGENCY:ESCAPE/EGRESS/EXIT. SUMMARY TO BE PROVIDED ON A FUTURE DATE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.