Service bulletins for the 2015 Ram Promaster City
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
280 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| 68277402A | 2018-06-11. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL. Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure |
|---|---|
| RL305553A | 2018-06-11. Service bulletin. POWER TRAIN. 9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~ |
| 68105583A | 2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~ |
| STAR News No. 85 | 2018-06-11. Service bulletin. EQUIPMENT. STAR receives on average 1,000 contacts per day ? that?s 300,000 annual contacts for technical assistance. This same month last year we had over 40,000 open aged > 5 days tickets. As a result of focused efforts to verify vehicles are repaired and close tickets the number is now at just under 7,000 tickets. |
| BJA46597 | 2018-06-11. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; POWER TRAIN. Job aid - If you have a suspected TC shudder/vibration, check the Interactive Network for Service Bulletins for the vehicle you are working on. A test-drive snap shot may help you isolate the source of the issue. |
| 82214739A | 2018-06-04. Service bulletin. TIRES; WHEELS; EQUIPMENT. Spare Tire Kit For vehicles with Alloy Wheels, an adapter is required (not included) to connect the alloy wheel to the spare tire winch cable when storing under the vehicle. The adapter is part number 68294863AA and requires three (3) mounting nuts; PN 68150129AA.~ |
| 18-063-17 | 2018-06-04. Service bulletin. POWER TRAIN. Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set:P0128 - Thermostat Rationality. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0171 - Fuel System 1/1 Lean. P0441 - EVAP Purge System Performance. P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0335 - Crankshaft Position Sensor Circuit. P0456 - EVAP System Small Leak. P0506 - Idle Speed Performance Lower Than Expected. P0507 - Idle Speed Performance Higher Than Expected. P1185 - General Pressure Sensor Correlation. P1607 - PCM Internal Shutdown Timer Rationality. P2610 - PCM Internal Engine Off Timer Performance. C0501 - Wheel Speed Signal Left Front Rationality. C0507 - Wheel Speed Signal Right Front Rationality. C050D - Wheel Speed Signal Left Rear Rationality. C0513 - Wheel Speed Signal Right Rear Rationality. U0402 - Implausible Data Received From TCM - (Transmission Control Module). In addition the following enhancements are included:Enhancements which allow the catalytic convertor to operate cooler. Enhancements to AC compressor clutch cycling. Increased RPM on start up. Reduced RPM when transmission is shifted into drive or reverse and cold. |
| 21-018-17 REV. A | 2018-06-04. Service bulletin. POWER TRAIN. Flash: Transmission Shift and Driveability Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P0887 - TCM Power Control Circuit High. P1720 - Output Speed Sensor-Wheel Speed Rationality. P1634 - Output Speed Sensor-Wheel Speed Rationality. P1DCCD - TCM Monitoring Processor Performance Multiple Clutches Locked Up. P0711 - Transmission Fluid Temperature Sensor A Circuit Range-Performance. P1DAD - Input Shaft-Output Shaft Direction Correlation. P1CC9 - Unable To Engage Gear. In addition the following enhancements are included:Calibrations to support changes in air flow to protect the catalyst. Transmission shift quality. Enable the capability to capture non-DTC control module data through the Uconnect data recording system. |
| 9003737 | 2018-06-04. Service bulletin. EQUIPMENT. Restraints Information Sheet (I-Sheet) has been added to Star Parts. Print I-Sheet fortechnician use. |
| 9003413 | 2018-06-04. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault. |
| 68184926A$ | 2018-05-21. Service bulletin. ELECTRICAL SYSTEM. Integrated Center Stack If vehicle is found within 50 mile radius of the Detroit Metro area please hold vehicle and contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~ |
| 68103198A$ | 2018-05-21. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. A/C Compressor This applies to 2015 and 2016 UF and PF. Before replacing the AC compressor for noise, leaks , or in-op:~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ 1) Check all AC plumbing connection for leaks with UV light. Any leaks found?~ 2) Does compressor pulley and clutch hub turn freely, or are they seized?~ 3) What was the amount of the recovered refrigerant?~ After these questions have been answered please call one of the individuals below.~ Stev at cell (248) 867-0061~ Mark Briolat at cell (248) 345-0127~ If no response in 15 minutes, please continue with repair.~ If the compressor is replaced, then:~ 4) Drain oil from compressor. What was quantity of oil recovered? |
| 05091960A$ | 2018-05-21. Service bulletin. ELECTRICAL SYSTEM. Hands Free Module - CTM ? Peiker For RT, JK and MK bodies only; Before replacing the Hands Free Module (HFM), please contact Gaurav Saxena at cell (248) 260-0583~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair. |
| 05066241A$ | 2018-05-21. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Battery - Transmitter For vehicles within 12 Months in Service which have a "FOB Battery Low" message within Cluster or DTC B1A10 or B1A11 Active or Stored. Engineering is requesting complete FOB returned unopened (ie, battery not removed or FOB housing opened!). ~ All others, follow normal procedures.~ Please ensure Dealer Technicians are aware of this request to allow for gain in FOB Battery depletion understanding. |
| 9002519 | 2018-02-21. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~ |
| RL108213A$ | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~ |
| 21-035-16 | 2017-11-03. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Transmission Shift And Drivability Enhancements For P0901-00. This bulletin involves performing transmission harness replacement per S55 recall.Both the PCM and TCM must be up to date for these changes to be effective after the transmission harness repair. Customers may experience a Malfunction Indicator Lamp (MIL) illumination after S55 recall TCM flash has been performed. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0901-00 - Clutch 1 Actuator Control Circuit Range Performance. |
| 9003491 | 2017-11-03. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. RESISTOR- Blower Motor, Blower Motor, Any AC Line, Compressor, Condenser For VM bodies ONLY; Prior to replacing this part, Please contact Karl Sonnenberg at Cell (248) 563-7740 prior to replacing the component. If you do not receive a response within 15 minutes, please continue with normal repair procedure. RETURN ALL PARTS. Put End Caps on all Lines. Describe where leak in line was detected. Take photo and email to karl.sonnenberg@external.fca.com. |
| 9003641 | 2017-11-03. Service bulletin. POWER TRAIN:DRIVELINE:CONSTANT VELOCITY JOINT. Shaft, Axle Half Clunking noise at low speed due to worn Half Shaft, CV Joint or Tripod Joint. Prior to any work or replacement of the part, please contact: Mike Perion @ cell: (248) 420-9016. If you don't receive a call back within 15 minutes, please proceed with normal repair. |
| 18-063-17 REV. A | 2017-11-03. Service bulletin. POWER TRAIN; ENGINE; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:U1424 - Implausible Engine Torque Signal Received. P1DD2-00 - Torque Request Signal From TCM Denied. U0402 - Implausible Data Received From TCM. P0128 - Thermostat Rationality. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0171 - Fuel System 1/1 Lean. P0441 - EVAP Purge System Performance. P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0335 - Crankshaft Position Sensor Circuit. P0456 - EVAP System Small Leak. P0506 - Idle Speed Performance Lower Than Expected. P0507 - Idle Speed Performance Higher Than Expected. P1185 - General Pressure Sensor Correlation. P1607 - PCM Internal Shutdown Timer Rationality. P2610 - PCM Internal Engine Off Timer Performance. C0501 - Wheel Speed Signal Left Front Rationality. C0507 - Wheel Speed Signal Right Front Rationality. C050D - Wheel Speed Signal Left Rear Rationality. C0513 - Wheel Speed Signal Right Rear Rationality. In addition the following enhancements are included:Enhancements which allow the catalytic convertor to operate cooler. Enhancements to AC compressor clutch cycling. Increased RPM on start up. Reduced RPM when transmission is shifted into drive or reverse and cold. |
| 9003355 | 2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. 3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair. |
| 21-013-16 REV. B | 2017-11-03. Service bulletin. POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. 948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic. |
| 18-008-16 REV. B | 2017-11-03. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, GASOLINE; WHEELS. Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set: · **P1185 - General Pressure Sensor Correlation.** · P0441 - EVAP Purge System Performance. · P0506 - Idle Speed Performance Lower Than Expected. · P0171 - Fuel System 1/1 Lean. · P050D - Cold Start Rough Idle. · P0507 - Idle Speed Performance Higher Than Expected. · U0402 - Implausible Data Received From TCM - (Transmission Control Module). · P1607 - PCM Internal Shutdown Timer Rationality. · P0335 - Crankshaft Position Sensor Circuit. · P0456 - EVAP System Small Leak. · P0133 - O2 Sensor 1/1 Slow Response. · P2610 - PCM Internal Engine Off Timer Performance. · P1607 - PCM Internal Shutdown Timer Rationality. · C0501 - Wheel Speed Signal Left Front Rationality. · C0507 - Wheel Speed Signal Right Front Rationality. · C050D - Wheel Speed Signal Left Rear Rationality. · C0513 - Wheel Speed Signal Right Rear Rationality. In addition the following enhancement are included: · Enhancements to AC compressor clutch cycling. · Increased RPM on start up. · Reduced RPM when shifted into drive or reverse when cold. |
| 5XP42TRMA$ | 2017-11-03. Service bulletin. STRUCTURE; EQUIPMENT; LATCHES/LOCKS/LINKAGES. FRT and Cargo Door Latches and External Handles. VM ONLY; External handle non functional due to latch cable link coming off the handle. Latch Binding/external handle binding. Before replacing dealer should call Carlos Dominguez at cell (248) 494-1534. (carlos.dominguez1@fcagroup.com) |
| 23-003-16 | 2017-10-25. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Transit Film This bulletin involves properly removing the vehicles transit film. When a new unsold vehicle arrives at the dealership, improper removal of the transit film can cause paint damage to the vehicle. Paint damage can occur if the transit film is not removed within six months of application. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.