WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Ram Promaster 3500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

186 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
18048232023-05-30. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
S21090000042023-01-17. Service bulletin. ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
S22090000042022-12-19. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
683328102022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.].
S21090000042022-09-26. Service bulletin. ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
18089192022-09-15. Service bulletin. ENGINE AND ENGINE COOLING. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
08014162022-07-05. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with the latest
S1809000007 Rev.2021-04-26. Service bulletin. ENGINE AND ENGINE COOLING. Customer complaint may include engine oil leak/consumption.
18-089-192019-12-16. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
OD553412019-07-15. Service bulletin. EQUIPMENT; ENGINE. Vehicles Eligible For CSN U07 And V08, V11 or V16 Important Update To U07 Dealer Instructions
549352019-07-15. Service bulletin. ENGINE; EQUIPMENT. Sensor-nitrous oxlde
553112019-07-15. Service bulletin. EQUIPMENT; ENGINE. Damper-Steering
553222019-07-15. Service bulletin. EQUIPMENT; ENGINE. Head-Cylinder
553242019-07-15. Service bulletin. ENGINE. Head-Cylinder
552212019-07-15. Service bulletin. ENGINE; EQUIPMENT. Engine Oil- OW20
550962019-07-15. Service bulletin. ENGINE. Engine Oil- OW20
549312019-07-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. TAILPIPE - EXHAUST
90033572019-07-15. Service bulletin. ENGINE; EQUIPMENT. ADAPTER, Engine Oil Filter (Pentastar V6) Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison (248-292-9510) ron.dallison@fcagroup.com Joe Lovell (734) 309-6467 - joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair. All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor.
132842018-12-17. Service bulletin. ENGINE. Title Filter - Engine Oil Start Date: 10/23/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of following part number: 68109834AA. Replacement part number is: 68229402AA. 68229402AA is designed to work on both DS and W K with 3.0L Ecodiesel(EXF)in NAFTA. Please return suspect parts back to your facing depot using Return Code 02, before 13 November, 2015. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com.
68080819A2018-11-26. Service bulletin. ENGINE. Camshaft Position Sensor If replacing a camshaft position sensor for P0340 and/or P0344 fault codes, please review information below and contact Andrew Action on his cell phone: (248) 421- 4130. If no response is received within 15 minutes, please continue with repair.~ Before clearing any codes please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Andrew Acton by email: andrew.acton@fcagroup.com~ Instructions to access CamCrank Sync Event Monitor:~ - From wiTECH main screen~ - Monitors tab~ - OBDII Monitors~ - Select Cam Crank Synchronization Event Monitor from the list~ - Should bring up 3 or 4 pages of data~ - Click on create PDF icon in lower right corner~ - email PDF to andrew.acton@fcagroup.com
68079375A2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Crankshaft Position Sensor Before replacing this part due to a P0335 fault code, please contact Andrew Acton at cell (248) 421-4130. Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data.
05191925A2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY. Radiator If vehicle comes in for transmission fluid leaking from trans-oil cooler fittings on the radiator, please check the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Loosen the hex nut on the top flared fitting on the radiator tank.~ 3. Torque the top flared fitting to 235 +/- 15 Lb-In.~ 4. Torque hex nut to 100 +/- 10 Lb-In.~ 5. Repeat for bottom flared fitting.~ 6. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~ ~ If vehicle is in need of a new radiator for another reason, check the new radiator for correct torque on the trans-oil cooler fitting per steps 2-5 above.~ ~ If radiator has a yellow mark by the trans-oil cooler fittings the torque does not have to be checked.
05149141A2018-11-26. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Camshaft Position Sensor If replacing a camshaft position sensor for P0340, P0344, P0345, P0349, P0365, P0369, P0390 or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com
04861963A2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT. Evaporative System Integrity Monitor switch (ESIM) Prior to replacing this component on a 2015 Dodge Journey (JC), please call Bob Bruni at cell (248) 736-8958. If a response is not received within 15 minutes, then continue with the necessary repair.
228422018-06-11. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. 05187880AC - Inspect and Return: Relay Assy - Heater Intake Air You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 05187880AC. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 31st August, 2016.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.