WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Ram 3500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

523 on file from NHTSA, as of 2026-10-19.

About P1477 on the 2015 Ram 3500: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P1477 are shown. Show all

Bulletins, newest first
18076222022-12-19. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); FUEL SYSTEM, GASOLINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); EXTERIOR LIGHTING; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE; FUEL SYSTEM, DIESEL; SERVICE BRAKES, HYDRAULIC; BACK OVER PREVENTION. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain ControlModule (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of thefollowing DTCs have been set: P064F - Unauthorized Software/Calibration Detected. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1C55 - NOx Sensor Intermittent ? Bank 1 Sensor 1. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P020A - Fuel Injector 1 Performance. P020B - Fuel Injector 2 Performance. P020C - Fuel Injector 3 Performance. P020D - Fuel Injector 4 Performance. P020E - Fuel Injector 5 Performance. P020F - Fuel Injector 6 Performance. U0001 - Can C Bus. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P218F - Reductant No Flow Detected. P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor CircuitIntermittent (setting when the block heater is plugged in). U110E - Lost Ambient Temperature Message. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. U1421 - Implausible Ignition Key Off Time Received. P026B - Injection Timing Performance. In addition, the following software enhancements are also available: A/C pressure sensor update. Improvements made to reduce misfire. wiTECH engine cooling fan actuation test update. Improved Exhaust Gas Recirculation (EGR) valve response. Over Running Clutch (ORC) software improvement. Unpleasantodor in the vehicle at low speeds during regeneration cycle.
18-037-162022-10-24. Service bulletin. FUEL SYSTEM, DIESEL; SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; POWER TRAIN; EXTERIOR LIGHTING; BACK OVER PREVENTION; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC). Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P2281 - Air Leak Between MAF And Throttle Body. · P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. · U1421 - Implausible Ignition Key Off Time Received. · P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **Ambient Air Temperature Improvements. · 68RFE Transmission Overall Shift Quality Improvements.** · SCR Efficiency scan tool test improvement. · Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). · Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. · Cold idle speed stability improvement. · Charging system improvements for dual alternator applications. · Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). · Fuel Filter Minder calibration changes. · wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.
18-037-162022-09-15. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); EXTERIOR LIGHTING; SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, DIESEL; POWER TRAIN. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P2281 - Air Leak Between MAF And Throttle Body. · P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. · U1421 - Implausible Ignition Key Off Time Received. · P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **NOx sensor calibration improvements. (Sales Code DG7). · Enhanced software for a No crank/No start issue. (U0100 - Lost Communication · Ambient Air Temperature (AAT) improvements. · 68RFE Transmission overall shift quality improvements. · SCR Efficiency scan tool test improvement. · Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). · Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. · Cold idle speed stability improvement. · Charging system improvements for dual alternator applications. · Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). · Fuel Filter Minder calibration changes. · wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.
18-041-15 REV A2019-05-20. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). ? U110E - Lost Ambient Temperature Message. ? P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. ? P2281 - Air Leak Between MAF And Throttle Body. ? P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. ? U1421 - Implausible Ignition Key Off Time Received. ? P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? SCR Efficiency scan tool test improvement. ? 68RFE Transmission Shift Quality Improvements for low speed First to Neutral and Neutral to First (Garage Shifts). ? Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). ? Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. ? Cold idle speed stability improvement. ? Charging system improvements for dual alternator applications. ? Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). ? Fuel Filter Minder calibration changes. ? wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.
18-041-152018-11-26. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one of more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. ? P2281 - Air Leak Between MAF And Throttle Body. ? P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. ? U1421 - Implausible Ignition Key Off Time Received. ? P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release. ? 68RFE Transmission Shift Quality Improvements for low speed First to Neutral and Neutral to First (Garage Shifts). ? Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). ? Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. ? Cold idle speed stability improvement. ? Charging system improvements for dual alternator applications. ? Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). ? Fuel Filter Minder calibration changes. ? wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.
18-037-162018-06-11. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P2281 - Air Leak Between MAF And Throttle Body. · P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. · U1421 - Implausible Ignition Key Off Time Received. · P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **Ambient Air Temperature Improvements. · 68RFE Transmission Overall Shift Quality Improvements.** · SCR Efficiency scan tool test improvement. · Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). · Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. · Cold idle speed stability improvement. · Charging system improvements for dual alternator applications. · Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). · Fuel Filter Minder calibration changes. · wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.
18-037-16 REV. A2018-06-04. Service bulletin. POWER TRAIN; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; EXTERIOR LIGHTING; FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P2281 - Air Leak Between MAF And Throttle Body. P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. U1421 - Implausible Ignition Key Off Time Received. · P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · NOx sensor calibration improvements. (Sales Code DG7). Enhanced software for a No crank/No start issue. (U0100 - Lost Communication With ECM/PCM). (Sales Code DG7).** · Ambient Air Temperature (AAT) improvements. · 68RFE Transmission overall shift quality improvements. · SCR Efficiency scan tool test improvement. · Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). · Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. · Cold idle speed stability improvement. Charging system improvements for dual alternator applications. · Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). Fuel Filter Minder calibration changes. · wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.