WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Ram 2500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

432 on file from NHTSA, as of 2026-10-19.

About P0128 on the 2018 Ram 2500: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

By topic

Only bulletins with trouble code: P0128 are shown. Show all

Bulletins, newest first
18080222022-12-19. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); BACK OVER PREVENTION; POWER TRAIN; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; EXTERIOR LIGHTING. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain ControlModule (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following DTCs have been set: P064F - Unauthorized Software/Calibration Detected. P2706 - MS Solenoid Circuit(68RFE Only). P0868 - Line Pressure Low. P229F - Aftertreatment NOxSensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2509 - PCM/PCM Power Input Signal Intermittent. P0401 - EGR System Performance. P0870 - OD Hydraulic Pressure Test. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P1C54 - SCR NOx Catalyst Missing. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P24C7 - Particulate Matter Sensor Temperature Circuit Performance. Customers may also comment on the following: Engine misfire in cold ambient temperatures. In addition, the following software enhancements are also available: Scan tool fan actuation test fix. Enabling diagnostics forDTC P208B- Reductant Pump 1 Control Performance. Unable to turn on the ability to set ?MAX? road speed using wiTECH scan tool. Mass Air Flow (MAF) sensor Out Of Range (OOR) low calibration. Improved 5-4 shift (reduce shift flare) after extended operation in 5th or 6th gear. Engine Manifold Pressure Misfire Monitor (EMP MFM) retune(68RFE Only). Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) out NOx sensor missingchange to 70 seconds. Map SCR missingFault/DTC P1C54to tampering inducement. Particulate Matter (PM) sensor false fault improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix.
1806120REVA2022-10-17. Service bulletin. SERVICE BRAKES; POWER TRAIN; BACK OVER PREVENTION; ELECTRICAL SYSTEM; EXTERIOR LIGHTING; FUEL SYSTEM, GASOLINE. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P2706 - MS Solenoid Circuit(Sales Code DG7 Only). P0868 - Line Pressure Low. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2509 - PCM/PCM Power Input Signal Intermittent. P0401 - EGR System Performance. P0870 - OD Hydraulic Pressure Test. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P1C54 - SCR NOx Catalyst Missing. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P24C7 - Particulate Matter Sensor Temperature Circuit Performance. Customers may also comment on the following:Engine misfire in cold ambient temperatures. In addition, the following software enhancements are also available:Scan tool fan actuation test fix. Enabling diagnostics forDTC P208B- Reductant Pump 1 Control Performance. Unable to turn on the ability to set ?MAX? road speed using wiTECH scan tool. Mass Air Flow (MAF) sensor Out Of Range (OOR) low calibration. Improved 5-4 shift (reduce shift flare) after extended operation in 5th or 6th gear. Engine Manifold Pressure Misfire Monitor (EMP MFM) retune(Sales Code DG7 Only). Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) out NOx sensor missing change to 70 seconds. Map SCR missingFault/DTC P1C54to tampering inducement. Particulate Matter (PM) sensor false fault improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN
18061202022-09-26. Service bulletin. POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0868 - Line Pressure Low (Module, Powertrain Control (PCM), 68RFE). P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2509 - PCM/PCM Power Input Signal Intermittent. P0401 - EGR System Performance. P0870 - OD Hydraulic Pressure Test. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P1C54 - SCR NOx Catalyst Missing. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P24C7 - Particulate Matter Sensor Temperature Circuit Performance. Customers may also comment on the following:Engine misfire in cold ambient temperatures. In addition, the following software enhancements are also available:Scan tool fan actuation test fix. Enabling diagnostics forDTC P208B- Reductant Pump 1 Control Performance. Unable to turn on the ability to set ?MAX? road speed using wiTECH scan tool. Mass Air Flow (MAF) sensor Out Of Range (OOR) low calibration. Improved 5-4 shift (reduce shift flare) after extended operation in 5th or 6th gear. Engine Manifold Pressure Misfire Monitor (EMP MFM) retune(68RFE Only). Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) out NOx sensor missing change to 70 seconds. Map SCR missingFault/DTC - P1C54to tampering inducement. Particulate Matter (PM) sensor false fault improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN) through wiTE
18-061-20 REV. A2020-11-30. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P2706 - MS Solenoid Circuit(Sales Code DG7 Only). P0868 - Line Pressure Low. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2509 - PCM/PCM Power Input Signal Intermittent. P0401 - EGR System Performance. P0870 - OD Hydraulic Pressure Test. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P1C54 - SCR NOx Catalyst Missing. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P24C7 - Particulate Matter Sensor Temperature Circuit Performance. Customers may also comment on the following:Engine misfire in cold ambient temperatures. In addition, the following software enhancements are also available:Scan tool fan actuation test fix. Enabling diagnostics forDTC P208B- Reductant Pump 1 Control Performance. Unable to turn on the ability to set ?MAX? road speed using wiTECH scan tool. Mass Air Flow (MAF) sensor Out Of Range (OOR) low calibration. Improved 5-4 shift (reduce shift flare) after extended operation in 5th or 6th gear. Engine Manifold Pressure Misfire Monitor (EMP MFM) retune(Sales Code DG7 Only). Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) out NOx sensor missing change to 70 seconds. Map SCR missingFault/DTC P1C54to tampering inducement. Particulate Matter (PM) sensor false fault improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN
18-061-202020-09-28. Service bulletin. ELECTRICAL SYSTEM; ENGINE; EQUIPMENT; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0868 - Line Pressure Low (Module, Powertrain Control (PCM), 68RFE). P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2509 - PCM/PCM Power Input Signal Intermittent. P0401 - EGR System Performance. P0870 - OD Hydraulic Pressure Test. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P1C54 - SCR NOx Catalyst Missing. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P24C7 - Particulate Matter Sensor Temperature Circuit Performance. Customers may also comment on the following:Engine misfire in cold ambient temperatures. In addition, the following software enhancements are also available:Scan tool fan actuation test fix. Enabling diagnostics forDTC P208B- Reductant Pump 1 Control Performance. Unable to turn on the ability to set ?MAX? road speed using wiTECH scan tool. Mass Air Flow (MAF) sensor Out Of Range (OOR) low calibration. Improved 5-4 shift (reduce shift flare) after extended operation in 5th or 6th gear. Engine Manifold Pressure Misfire Monitor (EMP MFM) retune(68RFE Only). Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) out NOx sensor missing change to 70 seconds. Map SCR missingFault/DTC - P1C54to tampering inducement. Particulate Matter (PM) sensor false fault improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN) through wiTE
18-036-202020-05-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. This bulletin fixes all vehicles listed and also contains an optional software path for situations where the customer is specifically complaining of a drone noise, shudder, pulsation, or vibration under light throttle applications, while vehicle is operating in Multi Displacement System/Economics (MDS/ECO) mode (optionalsoftware available for D2&DJ vehicles).There will be two separate software options displayed on the wiTECH flash tab. The software file released for this condition contains the verbiage ?MDS NOISE?. The other file is the standard software that does not contain improvements for the drone/shudder concern. If for some reason the customer finds this shudder improvementobjectionable, the PCM software may be returned/reflashed to the standard version.Both software versions will address the remaining conditions noted in the bulletin.The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P3402 - Cylinder 1 Deactivation Control Performance. P3426 - Cylinder 4 Deactivation Control Performance. P3442 - Cylinder 6 Deactivation Control Performance. P3450 - Cylinder 7 Deactivation Control Performance. P0128 - Thermostat Rationality. Customers may also describe the following condition:Heater not warming cabin sufficiently and engine slow to warm up. This condition could be caused by a malfunctioning thermostat which is not associated with an HVAC issue.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.