WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Ram 2500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

516 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
08-016-152022-09-26. Service bulletin. BACK OVER PREVENTION. Poor Radio Reception This bulletin involves replacing the satellite antenna if needed. A customer may experience, SXM (Sirius/XM) radio has intermittent muting. This occurs in areas where XM signal is degraded and cell signal is very weak. The condition happens when the optional vehicle internet connection through the cell network is in use with the internal vehicle Wi-Fi. This Symptom/Condition Only Applies To 2014-2015 KL Vehicles: A customer may experience a popping noise when listening to AM stations.
22-002-152022-09-26. Service bulletin. SERVICE BRAKES; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; BACK OVER PREVENTION. Service Tire Pressure System Message This bulletin involves inspecting and replacing the Tire Pressure Module (TPM) sensor if required. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): NOTE: The cluster will always display the low tire indicator if the tire pressure is under specification, or if there is a DTC set in the TPM system. If a DTC is set, the indicator will flash for 75 seconds and then stay on solid when the vehicle is started. ? C1501-07 Tire Pressure Sensor 1 - Mechanical Failure. ? C1501-31 Tire Pressure Sensor 1 - No Signal. ? C1502-07 Tire Pressure Sensor 2 - Mechanical Failure. ? C1502-31 Tire Pressure Sensor 2 - No Signal. ? C1503-07 Tire Pressure Sensor 3 - Mechanical Failure. ? C1503-31 Tire Pressure Sensor 3 - No Signal. ? C1504-07 Tire Pressure Sensor 4 - Mechanical Failure. ? C1504-31 Tire Pressure Sensor 4 - No Signal.
90044702022-09-26. Service bulletin. TRAILER HITCHES; ELECTRICAL SYSTEM:WIRING. CONNECTOR/WIRING, Trailer Tow If the connector or wiring is physically damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content
90043862022-09-26. Service bulletin. ELECTRICAL SYSTEM:WIRING. WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S20080001132022-09-26. Service bulletin. ELECTRICAL SYSTEM. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S18210000012022-09-26. Service bulletin. POWER TRAIN. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
1805314REVB2022-09-26. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN; BACK OVER PREVENTION; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING. Flash: 6.7L Diagnostic And System Improvements Bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows:Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit. P226C - Turgocharger Boost Control ?A? Slow Response.The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: U1A24 - Lost Communication With Ammonia Sensor.Improvements To Prevent/ Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: U3017 - Control Module Timer/Clock Performance. P0087 - Fuel Rail Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. P0128 - Thermostat Rationality. In cold ambient temperatures. P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. U1421 - Implausible Ignition Key Off Time Received. P0420 - Catalyst Efficiency Below Threshold. P026B - Injection Timing Performance. P04DB - Crankcase Ventilation System Disconnected. P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P0604 - Internal Control Module RAM. P1451 - Diesel Particulate Filter System Performance.Other Updates Included: Urea system calibration changes. Fuel Filter Minder Calibrat
1400114REVB2022-09-26. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM; STRUCTURE. Fuel Gelling in Cold Ambient Temperatures This bulletin involves reconfiguring the Body Control Module (BCM). Some customers may experience a Malfunction Indicator Lamp (MIL) due to fuel related Diagnostic Trouble Code (DTC) and/or may have a hard or no start condition due to fuel gelling in cold ambient temperatures (20°F or -7°C) or below. DTCs, such as P0087, P0191 or P026B (or other DTCs) may have been set.frame mounted fuel filter heater not to function. The condition is due to a configuration setting in the Body Control Module (BCM).
18072142022-09-26. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING; FUEL SYSTEM, GASOLINE. Flash: Compressed Natural Gas (CNG) Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. Software to prevent Malfunction Indicator Lamp (MIL) illumination with no defect found for Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM. Harsh shift improvement when shifting from drive to reverse.
1802514REVA2022-09-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Flash: Powertrain System Improvements/Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. The following powertrain system improvements/enhancements are included in this software release. These enhancements are listed by vehicle application.DS vehicles equipped with a 3.6L engine (sales code ERB). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DS vehicles equipped with a 5.7L engine (sales code EZH). Charging system voltage regulator control improvements. System improvements to prevent Malfunction Indicator Lamp (MIL) illumination with a Diagnostic Trouble Code (DTC) P0300 - Multiple Cylinder Misfire when using a block heater in ambient temperatures greater than -20°F (-29°C). Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy.DJ, DD, and D2 vehicles equipped with a 5.7L engine (sales code EZC) Transmission torque management enhancement when shifting from drive to reverse. Software to correct Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0481 - Cooling Fan 2 Control Circuit/Open setting in the PCM memory. Enhanced Automatic Oil Change Indicator(EAOCI) system improvements to switch to a severe duty cycle algorithm anytime the PCM is replaced to ensure the customer receives a timely oil change required message. Corrected a generic scan tool display issue regarding Mode 6 data accuracy. Improved transmission Quick Learn routine performance
11004142022-09-26. Service bulletin. BACK OVER PREVENTION. Chirp Type Noise Emitted From Exhaust This bulletin involves replacement of the muffler to correct a chirp type noise that is emitted from the exhaust when the engine enters MDS mode. Vehicle operators may experience the following condition: Chirp Type Noise Emitted From Exhaust when entering MDS mode
25005142022-09-26. Service bulletin. FUEL SYSTEM, DIESEL; FUEL SYSTEM, GASOLINE. Diesel Exhaust Fluid This bulletin provides information regarding the Diesel Exhaust Fluid (DEF) vehicle delivery fill guidelines.
18004142022-09-26. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM; BACK OVER PREVENTION. Flash: Malfunction Indicator Lamp (MIL) Illumination. Includes Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: (Further improvements over what was released in SB 18-004-14) (applies only to DD/DP vehicles) (applies only to DD/DP vehicles) P2066 - Fuel Level Sensor 2 Performance (applies only to DJ/D2 vehicles) P0441 - Evap Purge System Performance P2504 - Charging System Output High P04D0 - Cooled EGR Temperature Sensor Circuit Low P04D1 - Cooled EGR Temperature Sensor Circuit High (applies only to DD vehicles equipped with a DFP automatic transmission)
25003142022-09-26. Service bulletin. ENGINE. Information: P207F P1C70 And SCR Inducement Strategy
90025032022-09-26. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. RHR Radio Issue Description: Issue 1: While performing RHR radio reflash (software update), on rare occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect
S1623000028RevD2022-09-26. Service bulletin. VISIBILITY. Outside Power Fold Rearview Mirror Appears Loose Or Shakes
S1709000010RevB2022-09-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR; UNKNOWN OR OTHER. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
90043512022-09-26. Service bulletin. SERVICE BRAKES. PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
90036002022-09-26. Service bulletin. EQUIPMENT:ELECTRICAL. USB Charging port.
31005192022-09-15. Service bulletin. STRUCTURE. Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31003192022-09-15. Service bulletin. STRUCTURE. Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31004192022-09-15. Service bulletin. VISIBILITY. Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31006192022-09-15. Service bulletin. STRUCTURE; EQUIPMENT. Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
08111192022-09-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.