WenmarOpen by Wenmar Pro

Service bulletins for the 2024 Ram 1500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

374 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Steering are shown. Show all

Bulletins, newest first
S25190000092025-10-02. Service bulletin. ELECTRICAL SYSTEM; STEERING. Diagnostic Trouble Code (DTC) C221F-00, C2223-00, C221C-00, C0051-54 Present After Electric Power Steering (EPS) Replacement.
S25190000062025-07-23. Service bulletin. ELECTRICAL SYSTEM; STEERING. Steering Repair Information Involving Toe Angle. Tie Rod And Or Electric Power Steering (EPS) Units.
91004872025-01-15. Service bulletin. STEERING. MODULE Steering Control Before replacing the steering column control module (SCCM) due to turn signal inop, wipers inop, steering controls inop, TCS light DTC C0051 or horn blowing while turning, please follow these steps: 1.- Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. 7.- Before replacing the SCCM disconnect it and reconnect it again. If there are no DTC's active, physical defects, steering controls inop, wipers inop, nor turn signal inop, horn inop, then SCCM does not need to be replaced.
91003622024-07-08. Service bulletin. ELECTRICAL SYSTEM; STEERING. MODULE Steering Control Before replacing the steering column control module (SCCM), please follow these steps: 1.- Make sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.
91003542024-06-10. Service bulletin. VISIBILITY/WIPER; STEERING; VEHICLE SPEED CONTROL; ELECTRICAL SYSTEM. SWITCH Multifunction Before replacing the steering column control module (SCCM), please follow these steps: 1.- Make sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Review the SCCM for any physical issue (Autolock, clockspring damaged) 3.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.
979602024-05-16. Other. STEERING. MODULE - STEERING CONTROL
91001942023-09-25. Service bulletin. STEERING. EPS Steering Gear Prior to replacing EPS gear for Can C Bus Diagnostic Trouble Codes (DTCs), U0001 & U0002, please contact FCA Redacted Content. Please have the following info available: VIN, vehicle complaint, diagnostics completed, first name and last name, Dealer code, Service Manager name, Phone number or email address. If no response received in 15 minutes, proceed with part repair.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.