WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Ram 1500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

526 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
S25050000012025-03-05. Service bulletin. ENGINE. CEL (Check Engine Lamp) C006A-49 Multi-Axis Acceleration Sensor Internal Electronic Failure And C10CC-00 ESC Sensors.
09023232024-01-16. Service bulletin. ENGINE AND ENGINE COOLING. Throttle Blade Icing Service Fix Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P2072 - Electronic Throttle Control System - Ice Blockage. ? P2110 - Electronic Throttle Control - Forced Limited RPM. ? P2118 - Electronic Throttle Control Motor Current Performance - Bank 1. The customer may also comment on the following: ? The vehicle may not start (below freezing conditions - typically -7 °C (-20 °F)) This bulletin involves removing the PCV valve and hose to dry out, drying out the throttle body and installing an updated make-up air hose, air cleaner lid and changing the oil.
9003357A2024-01-02. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
07007232023-07-31. Service bulletin. ENGINE AND ENGINE COOLING. Water Quality When Mixed With Engine Coolant
18048232023-05-30. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
9003357a2023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
90033572023-04-17. Service bulletin. ENGINE AND ENGINE COOLING. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
S21090000042023-01-17. Service bulletin. ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
850492023-01-09. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION:SEALS/GASKETS; UNKNOWN OR OTHER. COOLER - EGR
90037042023-01-09. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S22090000042022-12-19. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
683328102022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.].
90028872022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
90037042022-09-26. Service bulletin. SEATS; FUEL SYSTEM, GASOLINE; AIR BAGS; POWER TRAIN; BACK OVER PREVENTION; ENGINE AND ENGINE COOLING. Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S21090000042022-09-26. Service bulletin. ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
08072142022-09-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE. Intermittently The Vehicle Will Not Shift Out Of Park This bulletin involves replacing the electronic shifter, if required. The customer may experience not being able to shift out of park. This condition can be corrected by turning off the vehicle and allowing all of the modules to go to sleep. Once the modules have gone through a key cycle the DTC will go from active to stored and then the vehicle can be shifted out of park. On further inspection DTCs P0607-00-ECU INTERNAL PERFORMANCE and P0928-00-BTSI CONTROL may be found active or stored.
S1709000010RevB2022-09-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR; UNKNOWN OR OTHER. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
08048132022-09-26. Service bulletin. ENGINE AND ENGINE COOLING. Flash: Coolant Gauge Reads Incorrectly Too High This Bulletin involves updating the Instrument Panel Cluster (IPC) software. A customer may note that the coolant temperature gauge looks like the engine temperature is high, the needle on the gauge will be at the 3/4 mark. On further inspection the technician will find the vehicle is running at normal temperature 228 to 230F/109-110C. After the cluster is updated the Temperature gauge will read at the 1/2 way mark, at normal operating temperature.
N350606132022-09-26. Service bulletin. ENGINE AND ENGINE COOLING; AIR BAGS. Some of the above vehicles equipped with premium tail lamps may not give the driver notification of a turn signal malfunction. This condition does not conform to Federal Motor Vehicle Safety Standard (FMVSS) No. 108 ? Lamps, Reflective Devices, and Associated Equipment.
18-034-14 REV. A2022-08-15. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
07-004-12 REV. A2022-07-25. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. Attention! Release Of New Engine Coolant Organic Additive Technology (OAT) Chrysler Corporation LLC. has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.
N250508132022-07-18. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; ENGINE AND ENGINE COOLING. New Safety Recall Advanced Communication ? N25050813 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2013 model year (DS) RAM Trucks (1500 series) equipped with a 3.6L engine (sales code ERB). Some of the above vehicles were built with a 3-way coolant valve that may become inoperable due to an improperly soldered circuit board in the valve. If the 3-way coolant valve sticks in a position that does not allow coolant flow to the heater core, the vehicle will not defrost the windshield as specified in Federal Motor Vehicle Safety Standard (FMVSS) No. 103 - Windshield Defrosting and Defogging Systems. NOTE: The 3-way coolant valve controls the flow of engine coolant to the heater core and transmission heater. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the date code on the 3-way coolant valve. 3-way coolant valves built within a specific date range must be replaced. The Powertrain Control Module (PCM) must also be recalibrated with new software. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.
S1709000010 Rev.2022-07-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
N220404132022-07-18. Service bulletin. EQUIPMENT; PARKING BRAKE; ENGINE AND ENGINE COOLING. Some of the above vehicles were built with the park brake equalizer improperly adjusted. Some vehicles may not be able to hold on a 20% grade as specified in Federal Motor Vehicle Safety Standard (FMVSS) No. 135 ? Light Vehicle Brake Systems.
18-017-132022-07-18. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING; POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: P26AB-Engine Coolant Bypass Valve Stuck

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.