WenmarOpen by Wenmar Pro

Recalls that may apply to the 2008 Peterbilt 388

A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.

By component

United States: NHTSA, as of 2026-10-19
20V1990002020-04-06. SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT; ELECTRONIC STABILITY CONTROL (ESC). PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."
15V1320002015-03-06. EQUIPMENT:OTHER:LABELS; TIRES. PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)." Built 2005-07-25 to 2016-02-26.
14V1450002014-03-25. SERVICE BRAKES. PACCAR, Inc. (PACCAR) is recalling certain model year 2008-2013 Peterbilt 365, 367, 388, 389 trucks manufactured October 6, 2007, through September 23, 2013. The affected vehicles were built with 16.5" x 7" front drum brakes and Bendix ES-420 brake linings installed on front axles rated to carry between 20,001 and 22,000 lbs GAWR and larger SLR (20.5" to 21.5") tires, however these brake linings are not rated for this configuration. Thus, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems." Built 2007-10-06 to 2013-09-23.
13V5930002013-11-25. EQUIPMENT:OTHER:LABELS. Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification." Built 2003-04-03 to 2013-10-25.
11V3800002011-07-21. ELECTRICAL SYSTEM:SOFTWARE. PACCAR IS RECALLING CERTAIN MODEL YEAR 2011-2012 KENWORTH T660, T700, AND T800 VEHICLES MANUFACTURED FROM APRIL 19, 2010, THROUGH MAY 13, 2011, AND MODEL YEAR 2008, 2010, AND 2011 PETERBILT 365, 367, 384, 386, 387, 388 AND 587 VEHICLES MANUFACTURED FROM APRIL 20, 2010, THROUGH JUNE 11, 2011, AND EQUIPPED WITH PACCAR MX ENGINES AND EATON ULTRASHIFT DM OR ALLISON AUTOMATIC TRANSMISSIONS (WITHOUT AUTO-NEUTRAL). THE FAST IDLE CONTROL MAY BE ACTIVATED BY THE OPERATOR WHILE THE TRANSMISSION IS IN GEAR. Built 2010-04-20 to 2011-06-11.
11V1270002011-02-23. FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY. PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2012 KENWORTH T2000, T660, T700, T800, AND W900, AS WELL AS MODEL YEAR 2009-2012 PETERBILT 365, 367, 384, 386, 387, 388, 389, AND 587 TRUCKS EQUIPPED WITH PACCAR MX ENGINES. THE OIL MODULE CENTRIFUGAL SPINNER FILTER CAP IN THE PACCAR MX ENGINE MAY BECOME LOOSE, POSSIBLY ALLOWING THE CAP TO COME OFF AND ENGINE OIL TO PARTIALLY DISCHARGE FROM THE OIL MODULE ONTO EXHAUST COMPONENTS.
10V6340002010-12-13. POWER TRAIN:AXLE ASSEMBLY. PACCAR IS RECALLING CERTAIN MODEL YEAR 2007-2008 KENWORTH AND PETERBILT VEHICLES MANUFACTURED FROM FEBRUARY 2, 2006 THROUGH APRIL 30, 2007. THE BEARING SURFACES OF THE EXTENDED LUBE UNIVERSAL JOINT THAT ATTACHES THE INTER-AXLE DRIVELINE TO THE DRIVE AXLE MAY BECOME PREMATURELY WORN DUE TO BREAKDOWN OF LUBRICATION AND/OR EXCESSIVE HEAT. PREMATURELY WORN BEARING SURFACES MAY RESULT IN THE U-JOINT BECOMING LOOSE AND/OR BINDING. THIS CONDITION MAY RESULT IN UNIVERSAL JOINT FAILURE, ALLOWING THE INTER-AXLE DRIVELINE TO DETACH FROM THE AXLE. Built 2006-02-02 to 2007-04-30.
10V3080002010-07-02. STEERING:COLUMN. PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2010 TRUCKS EQUIPPED WITH TRW STEERING SHAFTS. THE CIRCUMFERENTIAL WELD AROUND THE STEERING SHAFT TUBE THAT WELDS THE SPLINED TUBE TO THE NON-SPLINED TUBE MAY BE MISLOCATED. MISLOCATION OF THE CIRCUMFERENTIAL WELD MAY ALLOW THE SPLINED TUBE AND NON-SPLINED TUBE TO ROTATE RELATIVE TO ONE ANOTHER DURING A LOW SPEED, HIGH TORQUE TURN, POSSIBLY RESULTING IN A SEPARATION OF THE TWO TUBES. Built 2008-07-04 to 2009-04-20.
08V4870002008-09-23. ENGINE AND ENGINE COOLING:ENGINE:DIESEL. PACCAR IS RECALLING 4,883 MY 2006-2009 KENWORTH T600, T660, T800, W900, T2000 AND MY 2008-2009 PETERBILT 365, 367, 379, 384, 386, 387, 388 AND 389 TRUCKS. INADEQUATE STIFFNESS OF THE DIESEL PARTICULATE FILTER (DPF) BRACKET COULD RESULT IN SEPARATION OF THE DPF FROM THE CHASSIS.
08V1040002008-03-10. TRAILER HITCHES. PACCAR IS RECALLING 318 MY 2007-2009 KENWORTH T800, W900, AND PETERBILT 357, 365, 367, 378, 379, 384, 385, 386,388, AND 389 TRUCKS EQUIPPED WITH PREMIER TRAILER HITCH ASSEMBLIES. THE PINTLE HITCH ASSEMBLIES MAY HAVE BEEN MANUFACTURED IN A MANNER RESULTING IN A REDUCTION OF FATIGUE STRENGTH OF THE PIVOT PINS. Built 2006-06-01 to 2008-01-31.
08V0650002008-02-07. LATCHES/LOCKS/LINKAGES:DOORS:LATCH. PACCAR IS RECALLING 6,169 MY 2008 KENWORTH T300, T660, T800, T2000, W900 AND C500 VEHICLES AND MY 2008-2009 PETERBILT MODELS 365, 367, 384, 387, 388, 389 AND 389 KITS. CERTAIN DOOR LATCH ASSEMBLIES ON THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 206, 'DOOR LOCKS AND DOOR RETENTION COMPONENTS." THE ROTOR IN SOME OF THESE DOOR LATCH ASSEMBLIES DID NOT RECEIVE THE PROPER HEAT TREATMENT AND MAY BE SOFT. Built 2007-10-11 to 2008-01-10.
08V0020002008-01-08. SERVICE BRAKES, AIR:SUPPLY:HOSES, LINES/PIPING, AND FITTINGS. CERTAIN TRUCKS EQUIPPED WITH EATON SYNFLEX ECLIPSE BRAND EXTRUDED NYLON AIR BRAKE HOSE TUBING FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 106, "BRAKE HOSES." THE TUBING WAS MANUFACTURED WITH ONLY FOUR LAYERS OF NYLON MATERIAL, INSTEAD OF THE SPECIFIED FIVE LAYERS. Built 2007-10-16 to 2007-11-14.
07V5910002007-12-20. STEERING:GEAR BOX:SHAFT SECTOR. ON CERTAIN KENWORTH AND PETERBILT HEAVY DUTY TRUCKS EQUIPPED WITH TAS-85 TRW STEERING GEARS, THE INNER SURFACE OF THE OUTER SECTOR SHAFT TEETH OF THE STEERING GEARS MAY HAVE AN INCORRECT INVOLUTE PROFILE, WHICH MAY LEAD TO CHIPPING AND DAMAGE OF THE GEARING SYSTEM. Built 2007-08-24 to 2007-11-21.
07V4090002007-09-10. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY. ON CERTAIN PETERBILT TRUCKS, THE LONGITUDINAL SEAMS ON THE FUEL TANKS WERE FABRICATED USING AN INCORRECT WELD SPEED FOR THE GIVEN MATERIAL THICKNESS. THIS ERROR RESULTED IN A WELD WHICH DID NOT COMPLETELY PENETRATE THE ENTIRE MATERIAL THICKNESS. Built 2007-06-26 to 2007-07-31.
07V2870002007-07-05. ENGINE AND ENGINE COOLING. ON CERTAIN TRUCKS BUILT WITH CUMMINS ISM C876 ENGINES, THE ELECTRONIC CONTROL MODULE FAILS TO RECOGNIZE INPUTS OF THE VEHICLE ELECTRONIC CONTROL UNIT OR FROM A DRIVER ACTUATED DASH SWITCH THEREBY INCREASING THE RISK OF UNINTENDED (OR UNEXPECTED) ELEVATED EXHAUST TEMPERATURES. Built 2006-09-15 to 2007-04-27.
07V1320002007-03-22. POWER TRAIN:AXLE ASSEMBLY. ON CERTAIN TRUCKS, THE AXLE HOUSINGS MAY HAVE BEEN MANUFACTURED WITH STEEL THAT WAS OUT OF SPECIFICATION WHICH COULD RESULT IN A FATIGUE FAILURE OVER TIME. Built 2006-11-27 to 2007-02-28.
06V4900002006-12-21. SUSPENSION. ON SOME PETERBILT TRUCKS, CERTAIN PARTS USED IN THE AIR SUSPENSIONS HAVE A HIGH COPPER CONTENT CAUSING PREMATURE FAILURE. Built 2006-08-16 to 2006-11-22.
Canada: Transport Canada, as of 2026-10-19
20201482020-04-07. Lights And Instruments. Issue: On certain trucks, the warning light for the tractor anti-lock brake system (ABS) may not turn on if the system loses power. If this happens, the driver will not get warning that the ABS is not working properly. Note: This problem would also cause the traction control (TC) and electronic stability control (ESC) lights not to turn on. Safety Risk: If a driver is not warned that the ABS is not working properly, there could be an increased risk of a crash. Corrective Actions: PACCAR will notify owners by mail and instruct you to take your truck to a dealer to update the software for the cab control module (CECU).
20150952015-03-05. Label. Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 120 - Tire Selection and Rims. The tire information label may indicate incorrect tire pressure, understated by 5 PSI, or a tire/rim/inflation pressure combination for which the maximum GAWR is slightly below the GAWR of the vehicle. Underinflated tires may not be capable of supporting the maximum load as reflected by the GAWR and GVWR specified on the certification label, which could cause tire failure resulting in injury and/or damage to property. Correction: Manufacturer will mail new tire and rims certification label.
20140942014-03-25. Brakes. Certain vehicles fail to comply with the requirements of Canada Motor Vehicle Safety Standard 121 - Air Brake Systems. Incorrect brake linings were used on front drum brake assemblies fitted with large diameter tires (Static Load Radius of 20.5" - 21.5"), rendering the vehicles noncompliant to the standard. This could result in inadequate braking, increasing stopping distances and increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will install new brake shoes with the correct linings.
20112632011-07-21. Powertrain. On certain trucks equipped with a PACCAR MX engine and Eaton Ultrashift DM or Allison automatic transmission (without auto-neutral), the Fast Idle Control (also known as high idle) may be activated by the operator while the transmission is in gear. This could override the parking brake, allowing the vehicle to move unexpectedly. Unintended vehicle movement could result in a crash causing property damage and/or personal injury. Correction: Dealers will update the engine control software.
20110872011-02-25. Engine. On certain vehicles equipped with a PACCAR MX engine, the oil module centrifugal spinner filter cap may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto nearby exhaust components. The discharge of engine oil onto hot exhaust components could result in a fire causing property damage and/or personal injury. Correction: Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap.
20104412010-12-13. Powertrain. On certain vehicles, the bearing surfaces of the extended lube universal joint that attaches the inter-axle driveline to the drive axle may become prematurely worn due to breakdown of the lubrification and/or excessive heat. Prematurely worn bearing surfaces may result in the u-joint becoming loose and/or binding. If undetected, the condition may result in universal joint failure, allowing the inter-axle driveline to detach from the axle, which may cause the vehicle to become disabled in the roadway. Lost propulsion, in conjunction with traffic, road conditions, and the driver's reactions, could increase the risk of a crash. In addition a driveline component separating from the vehicle could strike another vehicle, stationary object, or bystander, causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace the interaxle driveline universal joint.
20083492008-09-24. Other. On certain trucks, the inadequate stiffness of the Diesel Particulate Filter (DPF) bracket could result in the separation of the DPF from the chassis, which could result in personal injuries or death to motorists or bystanders. Correction: Caterpillar dealers will replace bracket as necessary.
20080472008-02-12. Other. On certain vehicles, the door latch may have been manufactured incorrectly. If the latch rotor cracks, the latch would not have primary or secondary closing security. Attempting to drive a vehicle with a door in the unlatched position can result in increased risk of injury to an unbelted front seat occupant. Correction: Dealers will inspect and, if necessary, replace the latch assemblies.
20080182008-01-18. Fuel System. On certain trucks, fuel line fittings on the Aftertreatment Regeneration Device (ARD) may crack and leak fuel during a regeneration of the Diesel Particulate Filter. This could result in a vehicle fire. Correction: Dealers will replace the fuel line with an updated version that has fittings able to accommodate higher tightening torque.
20080012008-01-07. Brakes. Certain vehicles fail to comply with requirements of CMVSS 121 - Air Brake System. The air lines were incorrectly constructed with only four layers of extruded nylon material, instead of the specified five layers. Should the air lines develop a leak, while the vehicle is in motion, it could cause the air brake system to fail, which would engage the rear spring brakes, slowing the vehicle to a stop, and preventing it from being driven. Correction: Dealers will inspect and, if required, replace the air lines.
20074152007-12-18. Steering. On certain trucks, an incorrectly manufactured steering gear sector shaft may cause the steering to "stick or bind". This could severely restrict the steering turning angle, possibly resulting in a vehicle crash with injury or death. Correction: Dealers will replace the steering gear assembly.
20072922007-09-06. Fuel System. On certain trucks, the fuel tank's longitudinal seams may have been fabricated using an incorrect weld speed for the given material thickness. This error resulted in a weld which did not completely penetrate the entire material thickness. Fuel tanks possessing this defect could leak diesel fuel in the event of a vehicle crash. A fuel leak, in the presence of an ignition source, could result in a fire. Correction: Dealers will inspect and replace any defective fuel tank.
20070902007-03-20. Other. On certain trucks, the axle housing may have been manufactured with steel that was out of specification (9.5mm thick instead of 11mm thick), which could result in a fatigue failure over time. If failure occurs, the axle may lock-up or the end of the axle could come off, which may result in a vehicle crash with injury or death. Correction: Dealers will inspect and, if required, replace the axles.
20063692006-12-21. Suspension. On certain trucks, components used to attach the air suspension to the axle may contain elevated amounts of copper. The elevated copper content could result in component failure, which could cause erratic vehicle handling and a crash. Correction: Dealers will inspect and, if required, replace any suspect part with an updated version made with the correct metallurgical composition.

A campaign lists a year, a make and a model, and often only some of the vehicles built. A list with nothing on it is not a clearance either. The lookups below check one VIN.

Check one vehicle officially

Contains information licensed under the Open Government Licence – Canada.