WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Nissan Versa

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

160 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Equipment and accessories are shown. Show all

Bulletins, newest first
NTB15-044B2021-05-24. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP. Fuel Filler Cap tether clip service information
NTB11027B2021-05-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; TIRES. SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.
NTB15110A2021-05-10. Service bulletin. ELECTRICAL SYSTEM:IGNITION; POWER TRAIN:AUTOMATIC TRANSMISSION; EQUIPMENT. IF YOU CONFIRM * The key cannot be removed from the ignition. And/or * The Shifter will not move out of park. NOTE: For Rogue (T32), it is possible that shifter selector knob may not be installed correctly. Please refer to NTB14-058 for shift selector knob service information before applying this bulletin. ACTION a. Adjust the key interlock cable. b. Adjust the stop lamp switch. NOTE: Nissan vehicle warranty does not cover incidents due to lack of vehicle maintenance and/or physical damage. Refer to New Vehicle Limited Warranty in the Nissan Assurance Products Resource Manual (APRM) for warranty coverage guidelines and complete information regarding warranty coverage. Please see this bulletin for further details.
NTB15044B2021-05-10. Service bulletin. EQUIPMENT; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP. SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
NTB12099D2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). SERVICE INFORMATION: The Navigation (NAVI) SD Map Data Cards are not interchangeable between the two versions of NAVI units offered in Nissan vehicles that use this type of map data. * If the wrong SD Map Data Card is used, the NAVI will display an update screen (Figures 1 and 2, reference only) and will only accept Cancel. * If this screen is displayed, install the correct SD Map Data Card, found in table A on page 2, and the NAVI unit will return to correct operation. See this bulletin for further detail.
NTB11069C2021-05-10. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
NTB150822021-05-10. Service bulletin. BACK OVER PREVENTION; EQUIPMENT. IF YOU CONFIRM: An APPLIED VEHICLE has one or both of the following: * Hesitation during acceleration * MIL ON with DTC P0705 (Transmission Range Sensor A Circuit (PRNDL Input)) stored ACTION: 1. Inspect both rear tail lamp assemblies forwater intrusion (see page 2 for sample pictures). 2. If water intrusion is detected, inspect the circuit board of the tail lamp bulb holder(s) for corrosion (see page 2 for sample pictures). 3. If corrosion is found, replace the incident tail lamp assembly(ies). * Refer to the Electronic Service Manual (ESM), section EXL-Exterior Lighting System, for tail lamp replacement. * See PARTS INFORMATION on page 3. NOTE: * Replace only the tail lamp assembly where water intrusion has been detected. * Do NOT replace the CVT assembly for this incident, if it should occur. Please see this bulleitn for further details.
NTB15037A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; POWER TRAIN; STRUCTURE. IF YOU CONFIRM * If one or more of the DTC?s listed in Table A on page 2 are present in the Transmission Control Module (TCM). And * No other DTCs are present other than what are in Table A. And * The diagnostic procedures in the Electronic Service Manual (ESM) for each DTC in Table A, that is present in the TCM, has been performed and indicates that the CVT assembly must be replaced. NOTE: Do not replace CVT. ACTION Replace the CVT valve body assembly (control valve) with a unit from Parts Information using the Service Procedure starting on page 3. Please see this bulletin for further details.
NTB15033A2021-05-10. Service bulletin. EQUIPMENT; AIR BAGS. INTRODUCTION Nissan is conducting a Voluntary Safety Recall Campaign on certain specific Model Year 2012-2015 Versa Sedan and 2014-2015 Versa Note vehicles to remove material from the Center Console Lower. This service will be performed at no charge for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number P5308 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. Please see this bulletin for further detail.
NTB12055E2021-05-10. Service bulletin. WHEELS; POWER TRAIN; EQUIPMENT; BACK OVER PREVENTION. IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear CV-type axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. - For 2007-2013 Versa and 2013 LEAF vehicles, see the Service Procedure torque specifications on page 4. See this bulletin for further detail.
NTB150602021-05-10. Service bulletin. SERVICE BRAKES; WHEELS; BACK OVER PREVENTION; STEERING; EQUIPMENT. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
P53082021-05-10. Service bulletin. EQUIPMENT. Nissan is conducting a Voluntary Service Campaign on certain specific Model Year 2012 ? 2015 Versa Sedan and Versa Note vehicles to remove material from the Center Console Lower.
NTB99060G2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain, iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
NTB00042D2021-05-10. Service bulletin. AIR BAGS; BACK OVER PREVENTION; EQUIPMENT. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB13015A2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
NTB140772021-05-10. Service bulletin. EQUIPMENT; POWER TRAIN. SERVICE INFORMATION The purpose of this bulletin is to clarify language contained in the owner?s manual language for the APPLIED VEHICLES. For the APPLIED VEHICLES, the below language supersedes similar language in existing owner?s manuals. Future printings of owner?s manuals for the APPLIED VEHICLES will also contain the below language. For the APPLIED VEHICLES: NISSAN recommends using Genuine NISSAN NS-3 CVT Fluid ONLY in NISSAN CVTs. Do not mix with other fluids. Do not use Automatic transmission fluid (ATF) or Manual Transmission fluid in a NISSAN CVT, as it may damage the CVT. Damage caused by the use of fluids other than as recommended is not covered under NISSAN's New Vehicle Limited Warranty. Using fluids that are not equivalent to Genuine NISSAN NS-3 CVT Fluid may also damage the CVT. Damage caused by the use of fluids other than as recommended is not covered under NISSAN's New Vehicle Limited Warranty. See this bulletin for further detail.
NTB13077A2021-05-10. Service bulletin. EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT. SERVICE INFORMATION Applied vehicles equipped with a CVT have a "cap" that appears to be a fluid level gauge. This "cap" will NOT have a gauge or "dipstick". This is normal. Do NOT replace the "cap" because it is thought to have a "dipstick". The fluid level is not checked from this location. The fluid level for applied vehicles is checked from the oil pan (refer to the appropriate section of the Electronic Service Manual [ESM]). Whenever checking, filling, or topping off a CVT's fluid level of an applied vehicle for any reason, use the procedure outlined in the appropriate section of the ESM. See this bulletin for further detail.
NTB10066A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
NTB140082021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT; EQUIPMENT. SERVICE INFORMATION If for any reason you need to replace the CVT Oil Warmer/Cooler on an Applied Vehicle, it is now available as a service part. See this bulletin for further information.
NTB08055C2021-05-10. Service bulletin. EQUIPMENT; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB11005D2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
NTB92123D2021-05-10. Service bulletin. WHEELS; EQUIPMENT. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
NTB130452021-05-10. Service bulletin. BACK OVER PREVENTION; SEATS; EQUIPMENT. IF YOU CONFIRM While braking at a low speed, a moaning or squeaking/squealing noise is coming from the rear brakes. NOTE: The rear brake noise issue does not impact the functioning of the rear brakes. ACTION Replace both rear brake shoes with the new ones listed in the Parts Information section. - Refer to the BR-Brake System > REMOVAL AND INSTALLATION > REAR DRUM BRAKE section of the applicable Electronic Service Manual (ESM) for rear brake shoe removal and installation instructions. Seethis bulletin for further detail.
NTB12098A2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION The location of the Navigation (NAVI) SD Map Card has been changed for vehicles being shipped to dealers. - For the Applied Vehicles the NAVI SD Map Card is no longer in the Owners Manual Bag located in the trunk. - The Applied Vehicles now are shipped with the SD Map Card already inserted in the slot on the Face of the NAVI unit. IMPORTANT: SD Map Cards are not interchangeable between different versions of NAVI units and will cause the unit not to work until the original part number is installed. See this bulletin for further details.
NTB120952021-05-10. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. SERVICE INFORMATION - The Extended Storage Switch (ESS) now includes the enable/disable of BCM transit mode. - Operating the ESS will, at the same time, enable/disable the BCM transit mode with one operation (as opposed to separately on other models). - Together, the ESS and BCM transit mode are now referred to as "Shipping Mode." - The ESS is still located in the fuse panel. - Vehicles are shipped to dealers with the ESS disengaged (Shipping Mode) to help prevent the 12 volt service battery from becoming discharged during shipping and dealership storage. - Dealerships are required to push in the ESS prior to customer delivery. See this bulletin for further detail.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.