WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Nissan Rogue

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

318 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
NTB15084B2021-05-10. Service bulletin. POWER TRAIN. IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration), AND One of the following DTCs are stored in the TCM: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE: - If a transmission judder (as described above) is NOT reported by the customer, this bulletin does not apply. - If DTC P17F0 or P17F1 was NOT found stored, this bulletin does not apply. - NTB15-083, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart on page 2. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVT inspection possible. See this bulletin for further detail.
NTB160252021-05-10. Service bulletin. EQUIPMENT; BACK OVER PREVENTION; ELECTRICAL SYSTEM. SERVICE INFORMATION If an Air Bag Diagnosis Sensor Unit is replaced and the configuration of the old unit could not be saved, use the Service Procedure in this bulletin to: - Load the VIN specific configuration file from your electronic parts catalog (FAST or equivalent) onto a portable USB storage device (thumb drive) - Plug the thumb drive into your CONSULT PC. - Configure the new Air Bag Diagnosis Sensor Unit using the file that you loaded onto the thumb drive. See this bulletin for further detail.
NTB160212021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM: Any one or a combination of the following after opening and/or closing a door (as it applies): * The auto headlights do not time out after the ignition is set to the OFF position. * The interior lights do not come ON. * Rogue only: The radio will not turn OFF after ignition is turned OFF. * The Vehicle Information Display in the combination meter showing "door ajar" when the doors are closed. * The Remote Engine Start feature is inoperative. ACTION: 1. Remove, and then reinstall, the screw of all four (4) door switches. 2. Confirm whichever issue has been occurring is resolved. NOTE: If the issue(s) is still not resolved, refer to ASIST and the appropriate Electronic Service Manual (ESM) for further diagnosis. Please see this bulletin for further details.
NTB160202021-05-10. Service bulletin. ENGINE AND ENGINE COOLING. IF YOU CONFIRM The vehicle is operated as follows: 1. The ambient temperature is below freezing (below 32°F / 0°C). 2. The engine was started and the vehicle driven a short distance. 3. The vehicle was then parked (engine turned OFF), and then allowed to sit for at least 10 minutes. THEN, when restarting the engine: - The engine will crank but not start OR - The engine will start, but the engine will not respond to throttle pedal input. AND - One or more of the following Electronic Throttle Control (ETC) related DTCs are found stored in the ECM: -P2100 (ETC MOT PWR-B1) -P2101 (ETC FNCTN/CIRC-B1) -P1726 (ELEC TH CONTROL) ACTION Replace the Intelligent Power Distribution Module (IPDM) with the one listed in the PARTS INFORMATION section of this bulletin. - Refer to the Electronic Service Manual (ESM), section PCS-Power Control System, for IPDM removal and installation. See this bulletin for further detail.
NTB14015C2021-05-10. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. SERVICE INFORMATION When a BCM is replaced for any reason, TPMS (Tire Pressure Monitor System) configuration must be performed. TPMS configuration is in addition to any other BCM configurations that may be performed. If TPMS configuration is not performed, TPMS transmitter ID registration will not complete. Follow the Service Procedure in this bulletin to perform TPMS configuration. See this bulletin for further detail.
NTB03074J2021-05-10. Service bulletin. EXTERIOR LIGHTING. SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
NTB160182021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM The MIL is "ON" with DTC P0603 (ECM BACK UP/CIRCUIT). ACTION 1. Confirm that the battery voltage is 11 volts, or more, with the ignition ON (engine OFF, not running). 2. Erase DTC 3. Perform DTC confirmation steps in the Service Procedure. 4. Confirm 1st trip DTC P0603 is not stored. NOTE: P0603 is often the result of low battery voltage, discharged battery or battery terminal disconnections. Please see this bulletin for furtner details.
NTB15011A2021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM On an Applied Vehicle, one or more of the following is occurring: * A status message "Update Failed !" is displayed with a direction to "Insert update media" while a countdown from 60 is displayed. The audio system then reboots (Nissan Logo appears), and then will restart the countdown. * The center display screen (navigation screen) intermittently goes blank (nothing is displayed) for a few seconds or longer and then returns to normal display. * Continuously reboots (Nissan Logo appears after a loss of soundor freeze condition). * XM channel selection is sometimes not working as normal or shows "XM loading" for long periods of time. * Audio sometimes is not working. * Soundlevels for balance, fader, treble,or bass do not correspond to what is displayed by the audio unit after the ignition is cycled. * Connected iPod freezes after using "Source" button or changing tracks. * Audio preset buttons do not respond when selected. * Calls unintentionally change from "hands free" to "handset". And * The Software version has been confirmed as "not current" (refer to page 3). See this bulletin for further details.
NTB09081C2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
NTB160012021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION When the BCM in an APPLIED VEHICLE is being replaced for any reason, all existing Intelligent Keys must be re-registered. If new Intelligent Keys are added to the existing Intelligent Keys at the same time the BCM is being replaced, the procedure in this bulletin must be followed. See this bulletin for further detail.
PC419A2021-05-10. Service bulletin. LATCHES/LOCKS/LINKAGES. This activity will expire on December 18th, 2015. Dealers can continue to schedule and repair vehicles eligible for this service action until close of business December 18th, 2015. Claims will be honored for RO?s opened on or before the 18th of December.
NTB160032021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years. See this bulletin for further detail.
PC4192021-05-10. Service bulletin. LATCHES/LOCKS/LINKAGES. Nissan is conducting a dealer inventory service action to inspect and, if necessary, replace the hood latch on certain MY 2015 Murano, MY2016 Maxima, and MY2015-16 Rogue and Pathfinder vehicles
NTB150462021-05-10. Service bulletin. EQUIPMENT. Service Information * The tie down hook is no longer included with the jacking tools on 2015 Rogues, effective with the Applied Date shown above. * Do not submit warranty claims for a missing tie down hook (a hook that was not originally supplied with the vehicle). Please see this bulletin for further details.
NTB09022G2021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
NTB151032021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION The color of the rear cargo floor mats in the Applied Vehicles with almond color interior has changed. See this bulletin for further detail.
NTB14068A2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.
NTB10029C2021-05-10. Service bulletin. SUSPENSION. IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle; when making, turns, on dry roads, or at low speeds (under 40 MPH), and the vibration does not occur if the Electric Controlled Coupling is electrically disconnected. ACTION Replace the Electric Controlled Coupling for the rear final drive. See this bulletin for further detail.
NTB13028A2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NTB14114A2021-05-10. Service bulletin. PARKING BRAKE; SEAT BELTS; VEHICLE SPEED CONTROL. IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter). - All I-Key remote button functions (door lock/unlock, etc.) WILL work normally when all I-Key "hands free" functions are NOT working. ACTION 1. Inspect the I-Key?s battery on its negative contact side. 2. If excessive scratching is found, replace the battery. 3. Verify all I-Key functions (both "hands free" and remote) work properly after battery replacement. NOTE: Do NOT replace the BCM, I-Key, or other parts for the issue described under IF YOU CONFIRM, if it should occur. See this bulletin for further detail.
NTB12099D2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). SERVICE INFORMATION: The Navigation (NAVI) SD Map Data Cards are not interchangeable between the two versions of NAVI units offered in Nissan vehicles that use this type of map data. * If the wrong SD Map Data Card is used, the NAVI will display an update screen (Figures 1 and 2, reference only) and will only accept Cancel. * If this screen is displayed, install the correct SD Map Data Card, found in table A on page 2, and the NAVI unit will return to correct operation. See this bulletin for further detail.
NTB15062A2021-05-10. Service bulletin. STRUCTURE; BACK OVER PREVENTION; EQUIPMENT; SUSPENSION; ELECTRICAL SYSTEM. IF YOU CONFIRM There is a popping noise from either the right or the left front coil springs when turning to the right or left. NOTE: Electronic chassis ears may be helpful in isolating this type of noise. ACTION Replace both front coil springs, strut mount bearings, and all other parts listed under PARTS INFORMATION. Position the coil springs as shown on pages 2-5. Check the front end alignment, adjust to factory specifications as needed. NOTE: Refer to the Electronic Service Manual (ESM), section FSU Front Suspension, for strut coil spring removal, installation, and alignment information. IMPORTANT: The Coil Spring Installation Guidelines section in this bulletin MUST be followed in order for a correct repair to be performed.
NTB11069C2021-05-10. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit Mode. b. The "Extended Storage Switch" (if equipped) is in the "Customer Delivery" position (pushed in). - The Extended Storage Switch is located on the fuse block that is located in the interior of the vehicle. 2. Confirm the customer is familiar with the HomeLink programming procedure located in the vehicle?s owner?s manual. 3. Test HomeLink operation with special tool HomeLink Transmitter Tester J-41540. See this bulletin for further detail.
NTB150832021-05-10. Service bulletin. POWER TRAIN. IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on applied vehicles. These new DTC?s are: P17F1 (CVT_JUDDER (C/U INSPECTION)) P17F0 (CVT_JUDDER (T/M INSPECTION)) ACTION: 1. Refer to step 6 and TABLE A on page 4 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you areworking on. 2. If this bulletin applies, reprogram the TCM (Transmission Control Module). Please see this bulletin for further details.
NTB14029B2021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM All of the following - The engine will not start (no crank; starter will not engage) when pushing the ignition switch, and I-Key Error message is displayed in the combination meter, and DTC B2604 (PNP/Clutch Switch) is stored, past or present. ACTION Perform adjustment of the shift control cable per the Service Procedure in this bulletin. See this bulletin for further detail.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.