WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Nissan Rogue

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

332 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
NTB14-058B2021-05-24. Service bulletin. POWER TRAIN:SHIFT LINKAGE/CABLE/ROD:RETAINING FASTENERS/HARDWARE; EQUIPMENT. 2014-2016 Rogue; shift selector knob removal and Installation includfing the block-pull and spring
NTB13-099E2021-05-24. Service bulletin. EQUIPMENT:ELECTRICAL:AUX AUDIO JACK/PLUG; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Audio Ulnit Replacement - Vehicles with color display audio and navigation system
NTB12-103C2021-05-24. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT. CVT/TDCM Calibration Data "Write" Procedure
PC490OL2021-05-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. Nissan is conducting a voluntary service campaign to reprogram the Continuously Variable Transmission (CVT) software on specific 2014-16 L33 Altima and 2014-2016 Rogue vehicles
NTB12103D2021-05-10. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. SERVICE INFORMATION The Service Procedure (starting on page 2) in this bulletin contains the steps to perform TCM Calibration Data Write Procedures. These procedures are used when a complete CVT is replaced, or a CVT control valve (valve body) is replaced, or a Transmission Control Module (TCM) is replaced. See this bulletin for further detail.
NTB11027B2021-05-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; TIRES. SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.
NTB15026B2021-05-10. Service bulletin. POWER TRAIN; EQUIPMENT; ENGINE. IF YOU CONFIRM An Applied Vehicle experiences reduced power during extremely heavy snow fall, and snow is found inside the air cleaner case. NOTE: The MIL may be ON with DTC P0101 (MAF SEN/CIRCUIT B1) stored. ACTION See Repair Flow Chart on page 2 to confirm that this bulletin applies. See this bulletin for further detail.
NTB150872021-05-10. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN. IF YOU CONFIRM One or more of the DTCs listed in Table A are stored in the Transmission Control Module (TCM). And No other DTCs are stored other than what are listed in Table A. And The diagnostic procedures in the Electronic Service Manual (ESM) for each DTC in Table A, that is stored in the TCM, has been performed and indicates that the CVT assembly must be replaced. NOTE: Do not replace the CVT. ACTION Replace the CVT valve body assembly (control valve) with a unit from Parts Information. See page 2 for important information when replacing the CVT control valve.
NTB15013C2021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT; POWER TRAIN; EQUIPMENT. IMPORTANT: Metal debris and friction material may become trapped in the radiator, cooling hoses, bypass valve or external CVT fluid cooler. This debris can contaminate the newly serviced transmission, control valve or torque converter. In severe cases this debris can block or restrict flow and may cause damage to the newly serviced CVT. SERVICE INFORMATION When a CVT, control valve or torque converter replacement is necessary for one of the applied vehicles, the CVT transmission fluid coolers (radiator based fluid cooler and external auxiliary cooler if present) must be flushed. Please see this bulletin for further details.
NTB15113A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; ENGINE; EXTERIOR LIGHTING:BRAKE LIGHTS. IF YOU CONFIRM The following, or the customer reports the following: - Intermittently there is low power when accelerating, And/or - The stop lamps (brake lights) stay ON after releasing the brake pedal, with the ignition ON or OFF. ACTION - Delete the stop lamp relay and bypass the stop lamp relay circuit. - Replace the stop lamp switch with the one listed in PARTS INFORMATION. See this bulletin for further detail.
NTB160472021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. SERVICE INFORMATION Changes or modifications to the vehicle electrical system (including the installation of aftermarket remote-start devices) may affect the proper operation of the vehicle electrical systems. Installation of aftermarket remote-start devices may cause Intelligent Keys to not register, buttons in the Intelligent Key to not operate, and other electrical system related issues. See this bulletin for further detail.
NTB15110A2021-05-10. Service bulletin. ELECTRICAL SYSTEM:IGNITION; POWER TRAIN:AUTOMATIC TRANSMISSION; EQUIPMENT. IF YOU CONFIRM * The key cannot be removed from the ignition. And/or * The Shifter will not move out of park. NOTE: For Rogue (T32), it is possible that shifter selector knob may not be installed correctly. Please refer to NTB14-058 for shift selector knob service information before applying this bulletin. ACTION a. Adjust the key interlock cable. b. Adjust the stop lamp switch. NOTE: Nissan vehicle warranty does not cover incidents due to lack of vehicle maintenance and/or physical damage. Refer to New Vehicle Limited Warranty in the Nissan Assurance Products Resource Manual (APRM) for warranty coverage guidelines and complete information regarding warranty coverage. Please see this bulletin for further details.
NTB13106E2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); STEERING; ELECTRICAL SYSTEM; BACK OVER PREVENTION. SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.
NTB14058B2021-05-10. Service bulletin. EQUIPMENT; POWER TRAIN:MANUAL TRANSMISSION:FLOOR SHIFT ASSEMBLY; POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:FLOOR SHIFT; POWER TRAIN:MANUAL TRANSMISSION:COLUMN SHIFT ASSEMBLY; POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:COLUMN SHIFT. SERVICE INFORMATION This bulletin contains the procedure to remove and/or install the shift selector knob. It also contains information for re-installing the block-pull and spring, if needed. See this bulletin for further detail.
NTB13099E2021-05-10. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. SERVICE INFORMATION If the Audio Unit needs to be replaced in an Applied Vehicle for any reason: - Write down replacement Audio Unit's registration "code" . - Replace the Audio Unit as instructed in the Electronic Service Manual (ESM) and any applicable bulletins. - Register the replacement Audio Unit with Nissan Owner Services. NOTE: The Apps mode will not function if the Audio Unit serial number (registration code) is not registered. See this bulletin for further detail.
NTB09099A2021-05-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B2021-05-10. Service bulletin. FORWARD COLLISION AVOIDANCE; EQUIPMENT:OTHER:LABELS. SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB15044B2021-05-10. Service bulletin. EQUIPMENT; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP. SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
NTB160332021-05-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. SERVICE INFORMATION If the HVAC system control unit is replaced for any reason: - After replacement, make sure to perform Door Motor Starting Position Reset using CONSULT-III plus. - This function is found in HVAC > Work support. See this bulletin for further detail.
NTB15084B2021-05-10. Service bulletin. POWER TRAIN. IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration), AND One of the following DTCs are stored in the TCM: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE: - If a transmission judder (as described above) is NOT reported by the customer, this bulletin does not apply. - If DTC P17F0 or P17F1 was NOT found stored, this bulletin does not apply. - NTB15-083, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart on page 2. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVT inspection possible. See this bulletin for further detail.
NTB160252021-05-10. Service bulletin. EQUIPMENT; BACK OVER PREVENTION; ELECTRICAL SYSTEM. SERVICE INFORMATION If an Air Bag Diagnosis Sensor Unit is replaced and the configuration of the old unit could not be saved, use the Service Procedure in this bulletin to: - Load the VIN specific configuration file from your electronic parts catalog (FAST or equivalent) onto a portable USB storage device (thumb drive) - Plug the thumb drive into your CONSULT PC. - Configure the new Air Bag Diagnosis Sensor Unit using the file that you loaded onto the thumb drive. See this bulletin for further detail.
NTB160202021-05-10. Service bulletin. ENGINE AND ENGINE COOLING. IF YOU CONFIRM The vehicle is operated as follows: 1. The ambient temperature is below freezing (below 32°F / 0°C). 2. The engine was started and the vehicle driven a short distance. 3. The vehicle was then parked (engine turned OFF), and then allowed to sit for at least 10 minutes. THEN, when restarting the engine: - The engine will crank but not start OR - The engine will start, but the engine will not respond to throttle pedal input. AND - One or more of the following Electronic Throttle Control (ETC) related DTCs are found stored in the ECM: -P2100 (ETC MOT PWR-B1) -P2101 (ETC FNCTN/CIRC-B1) -P1726 (ELEC TH CONTROL) ACTION Replace the Intelligent Power Distribution Module (IPDM) with the one listed in the PARTS INFORMATION section of this bulletin. - Refer to the Electronic Service Manual (ESM), section PCS-Power Control System, for IPDM removal and installation. See this bulletin for further detail.
NTB14015C2021-05-10. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. SERVICE INFORMATION When a BCM is replaced for any reason, TPMS (Tire Pressure Monitor System) configuration must be performed. TPMS configuration is in addition to any other BCM configurations that may be performed. If TPMS configuration is not performed, TPMS transmitter ID registration will not complete. Follow the Service Procedure in this bulletin to perform TPMS configuration. See this bulletin for further detail.
NTB03074J2021-05-10. Service bulletin. EXTERIOR LIGHTING. SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
NTB15011A2021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM On an Applied Vehicle, one or more of the following is occurring: * A status message "Update Failed !" is displayed with a direction to "Insert update media" while a countdown from 60 is displayed. The audio system then reboots (Nissan Logo appears), and then will restart the countdown. * The center display screen (navigation screen) intermittently goes blank (nothing is displayed) for a few seconds or longer and then returns to normal display. * Continuously reboots (Nissan Logo appears after a loss of soundor freeze condition). * XM channel selection is sometimes not working as normal or shows "XM loading" for long periods of time. * Audio sometimes is not working. * Soundlevels for balance, fader, treble,or bass do not correspond to what is displayed by the audio unit after the ignition is cycled. * Connected iPod freezes after using "Source" button or changing tracks. * Audio preset buttons do not respond when selected. * Calls unintentionally change from "hands free" to "handset". And * The Software version has been confirmed as "not current" (refer to page 3). See this bulletin for further details.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.