Service bulletins for the 2009 Nissan Rogue
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
99 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| NTB17-082E | 2022-03-12. Service bulletin. FUEL SYSTEM, OTHER; ENGINE AND ENGINE COOLING. DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
|---|---|
| NTB13-027C | 2022-03-12. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB15055 | 2021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail. |
| NTB14018 | 2021-05-10. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail. |
| NTB12091A | 2021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); ENGINE. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail. |
| NTB12104 | 2021-05-10. Service bulletin. ENGINE AND ENGINE COOLING. SERVICE INFORMATION The R&I (Remove and Install) procedure on an applied vehicle for blower motor service will be amended to include the knee bracket. If a blower motor is to be removed and reinstalled or replaced, add the step shown in this bulletin. - The procedure for blower motor R&I is in the I VENTILATION, HEATER & AIR CONDITIONER>VTL Ventilation System section of all related ESMs. See this bulletin for further detail. |
| NTB17-082b | 2019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin. |
| Revision 1-NEVAP | 2019-01-07. Service bulletin. EQUIPMENT; ENGINE. OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time. |
| NTB-14-092 | 2014-12-13. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. NISSAN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ON CERTAIN VEHICLES, A VOLUNTARY EMISSION RECALL CAMPAIGN IS BEING CONDUCTED AND THE ENGINE CONTROL MODULE (ECM) WILL BE REPROGRAMMED. MODEL 2008-2010 ROGUE. *PE |
| NTB-14-002 | 2014-01-31. Service bulletin. ENGINE. NISSAN: SOME VEHICLES MAY EXPERIENCE REDUCED PERFORMANCE CAUSED BY THE CVT FLUID TEMPERATURE PROTECTION LOGIC. *JS UPDATED 4/18/14. *PE UPDATED 9/29/14. *PE |
| NTB12-043 | 2012-05-08. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS. NISSAN: IF FOR ANY REASON THE ENGINE HARNESS IS REPLACED, DURING THE REPLACEMENT OF THE HARNESS, INSTALL A RUBBER PROTECTIVE PAD ON THE BATTERY TRAY SUPPORT BRACKET. *JS UPDATED 5/24/2012 *JS |
| NTB-11-015A | 2011-09-28. Service bulletin. ENGINE AND ENGINE COOLING. NISSAN: OIL IS LEAKING FROM THE UPPER END OF THE ENGINE OIL COOLER. *RM |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.