Service bulletin NTB12104

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10192068
Published by NHTSA	2021-05-10
Manufacturer's number	NTB12104
Manufacturer's date	2012-11-14
NHTSA component	ENGINE AND ENGINE COOLING

NHTSA's summary

SERVICE INFORMATION The R&I (Remove and Install) procedure on an applied vehicle for blower motor service will be amended to include the knee bracket. If a blower motor is to be removed and reinstalled or replaced, add the step shown in this bulletin. - The procedure for blower motor R&I is in the I VENTILATION, HEATER & AIR CONDITIONER>VTL Ventilation System section of all related ESMs. See this bulletin for further detail.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine

Vehicles listed
NISSAN ROGUE	2008, 2009, 2010, 2011, 2012, 2013

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
NTB17-082E	2022-03-12. Service bulletin. DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J	2022-03-12. Service bulletin. EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C	2022-03-12. Service bulletin. CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15-113	2021-05-24. Service bulletin. 2013 Rogue and 2014 Rogue Select; Low Power/stop Lamps stay on.
NTB15113A	2021-05-10. Service bulletin. IF YOU CONFIRM The following, or the customer reports the following: - Intermittently there is low power when accelerating, And/or - The stop lamps (brake lights) stay ON after releasing the brake pedal, with the ignition ON or OFF. ACTION - Delete the stop lamp relay and bypass the stop lamp relay circuit. - Replace the stop lamp switch with the one listed in PARTS INFORMATION. See this bulletin for further detail.
NTB16020	2021-05-10. Service bulletin. IF YOU CONFIRM The vehicle is operated as follows: 1. The ambient temperature is below freezing (below 32°F / 0°C). 2. The engine was started and the vehicle driven a short distance. 3. The vehicle was then parked (engine turned OFF), and then allowed to sit for at least 10 minutes. THEN, when restarting the engine: - The engine will crank but not start OR - The engine will start, but the engine will not respond to throttle pedal input. AND - One or more of the following Electronic Throttle Control (ETC) related DTCs are found stored in the ECM: -P2100 (ETC MOT PWR-B1) -P2101 (ETC FNCTN/CIRC-B1) -P1726 (ELEC TH CONTROL) ACTION Replace the Intelligent Power Distribution Module (IPDM) with the one listed in the PARTS INFORMATION section of this bulletin. - Refer to the Electronic Service Manual (ESM), section PCS-Power Control System, for IPDM removal and installation. See this bulletin for further detail.
NTB15055	2021-05-10. Service bulletin. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
NTB14109	2021-05-10. Service bulletin. SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
PC327	2021-05-10. Service bulletin. Nissan is conducting an inventory inspection on 105,290 specific MY2013-15 Nissan ALT, PTH, LEF, MUR, NV2, NVT, SEN, and VER NOTE vehicles to inspect the software on the OCS ECU.
NTB14018	2021-05-10. Service bulletin. IF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail.