WenmarOpen by Wenmar Pro

Service bulletins for the 2008 Nissan Rogue

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

100 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
P9241 2008-09 Ro2021-06-12. Service bulletin. WHEELS. Expiration Notification – Wheel Valve Stem Nut ***** Campaign Summary***** In 2009, Nissan launched a Voluntary Service Campaign on certain 2008-2009 Rogue, 2009 Murano, and 2009 cube® vehicles registered in states that do not use heavy concentrations of road salt in the winter, to replace the Tire Pressure Monitoring System (TPMS) nut with new, more corrosion resistant ones. Nissan determined the material used in the nut on the Rogue, cube®, and Murano that secures the TPMS sensor to the wheel was not manufactured to specification and may corrode and potentially crack if driven regularly in areas where a heavy concentration of road salt is used. If this occurs, the nut may come out of the sensor causing the TPMS lamp to illuminate. If the TPMS lamp is disregarded, and the vehicle continues to be driven in this condition, the tire can quickly lose air pressure resulting in a flat tire. This customer service campaign and customer reimbursement for these repairs are no longer available. The expiration of this Voluntary Service Campaign has no effect on the status of Voluntary Safety Recall R0909. ***** What Dealers Should Do ***** 1. Service Comm will deactivate P9241 on any unrepaired VINs on May 13, 2021. No further dealer action is required.
NTB09-110A2021-06-11. Service bulletin. WHEELS. VOLUNTARY SERVICE CAMPAIGN ROGUE, MURANO, cube®; WHEEL VALVE STEM NUT Service Campaign ID # P9241 is no longer active. • Repair orders opened after this bulletin’s published date are no longer eligible for reimbursement under Campaign ID # P9241. • Discard all previous versions of NTB09-110.
NTB09099A2021-05-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B2021-05-10. Service bulletin. FORWARD COLLISION AVOIDANCE; EQUIPMENT:OTHER:LABELS. SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB09081C2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
NTB10029C2021-05-10. Service bulletin. SUSPENSION. IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle; when making, turns, on dry roads, or at low speeds (under 40 MPH), and the vibration does not occur if the Electric Controlled Coupling is electrically disconnected. ACTION Replace the Electric Controlled Coupling for the rear final drive. See this bulletin for further detail.
NTB13028A2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NTB13088A2021-05-10. Service bulletin. BACK OVER PREVENTION; WHEELS; SERVICE BRAKES; LANE DEPARTURE. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
NTB150702021-05-10. Service bulletin. STRUCTURE. IF YOU CONFIRM An oil leak from the Adapter Case Oil Seal or the O-ring (see Figure 1). ACTION NOTE: DO NOT replace the Transfer Case for a leak from the Adapter Case Oil Seal or the O-ring. Reseal the Adapter Case with the seals listed in PARTS INFORMATION and shown in Figure 1. * Please see this bulletin for further details.
NTB150602021-05-10. Service bulletin. SERVICE BRAKES; WHEELS; BACK OVER PREVENTION; STEERING; EQUIPMENT. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
NTB150552021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
NTB00042D2021-05-10. Service bulletin. AIR BAGS; BACK OVER PREVENTION; EQUIPMENT. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
NTB141072021-05-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
NTB10066A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
NTB140262021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM: An electrical issue caused by corrosion in the Main Harness to Body Harness connectors located at the bottom of the driver side A-pillar: Connector numbers M13 to B3 and/or M14 to B4. ACTIONS: 1. Preform repairs to harness connectors as needed. 2. Apply Harness Protector to cover the harness connectors. See this bulletin for further detail.
NTB140182021-05-10. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail.
NTB08055C2021-05-10. Service bulletin. EQUIPMENT; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB09020F2021-05-10. Service bulletin. FUEL/PROPULSION SYSTEM; EQUIPMENT. SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.
NTB92123D2021-05-10. Service bulletin. WHEELS; EQUIPMENT. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
NTB13027A2021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
NTB04094A2021-05-10. Service bulletin. STEERING; SERVICE BRAKES; WHEELS. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
NTB00033E2021-05-10. Service bulletin. SERVICE BRAKES; WHEELS; SUSPENSION; STEERING. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
NTB98018G2021-05-10. Service bulletin. ELECTRICAL SYSTEM. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
NTB99001A2021-05-10. Service bulletin. SUSPENSION. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
NTB11012B2021-05-10. Service bulletin. STRUCTURE. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.