WenmarOpen by Wenmar Pro

Service bulletins for the 2012 Nissan Maxima

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

115 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
NTB141092021-05-10. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
NTB141072021-05-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
NTB14060A2021-05-10. Service bulletin. STRUCTURE; ENGINE. SERVICE INFORMATION A two-piece design front engine mount is currently being used for the applied vehicles listed. A single thunk noise may be heard on the first acceleration of the day from this type of mount and is considered normal operation. The mount has also been designed with built in free-play that is normal. Under normal driving conditions: * A "thunk" noise may be heard on the first acceleration of the day. And * Does not occur again, or at any other time. DO NOT REPLACE THE MOUNT: * If it has free play or a "single event" thunk sound on the first acceleration of the day. This is considered a normal characteristic of this type of engine mount. * If a shift shock condition is present when shifting from park into gear or between any combination of gears. This condition is due to transmissions line pressures and not movement of the mount. NOTE: Refer to the Electronic Service Manual section TM - Transaxle & Transmission for further diagnostic information on shift shock. See this bulletin for further details.
NTB12116A2021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM - MIL is on with DTC's P0014 and/or P0024. - Customer describes a hesitation at speeds below 15 MPH after the oil was changed. ACTION Replace left and right cylinder bank's "Exhaust Valve Control Magnet Retarder". Please see this bulletin for further details.
NTB10066A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
NTB140322021-05-10. Service bulletin. ELECTRICAL SYSTEM:WIRING. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
NTB08055C2021-05-10. Service bulletin. EQUIPMENT; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NTB12091A2021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); ENGINE. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
NTB12071A2021-05-10. Service bulletin. ENGINE. IF YOU CONFIRM A knock noise coming from the # 1 crankshaft main bearing: ACTION 1. Remove the # 1 main bearing (upper and lower halves), per the Service Procedure in this bulletin. 2. Select and install a new # 1 main bearing that is one grade higher (thicker) than the one removed. See this bulletin for further detail.
NTB11005D2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
NTB92123D2021-05-10. Service bulletin. WHEELS; EQUIPMENT. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
NTB13027A2021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
NTB11103C2021-05-10. Service bulletin. FUEL SYSTEM, GASOLINE. SERVICE INFORMATION Part order approval from TECH LINE is no longer required when replacing the Audio Visual (A/V) Control Unit on an Applied Vehicle. Previously, TECH LINE would need to be contacted to confirm (or assist with) diagnosis and the proper repair prior to ordering an A/V control unit. This process has been suspended.
NTB04094A2021-05-10. Service bulletin. STEERING; SERVICE BRAKES; WHEELS. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
NTB00033E2021-05-10. Service bulletin. SERVICE BRAKES; WHEELS; SUSPENSION; STEERING. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
NTB130062021-05-10. Service bulletin. WHEELS; ELECTRICAL SYSTEM; SEATS; AIR BAGS; STEERING. SERVICE INFORMATION If you confirm there is a need to replace the steering wheel switches on an Applied Vehicle for any reason: - Do not replace the driver air bag module. The steering wheel switches are now available as a separate service part. - Refer to the Service Procedure in this bulletin for steering wheel switch removal and installation instructions. See this bulletin for more detail.
NTB130632021-05-10. Service bulletin. SUSPENSION; WHEELS; STRUCTURE; AIR BAGS. IF YOU CONFIRM: The front passenger seatback has a greater than normal vibration at highway speeds AND There are no other shake or vibrations with the vehicle. ACTION: Use the REPAIR FLOW CHART on page 3 to determine the repair(s) to be performed. NOTES: - The description under IF YOU CONFIRM must exist for this bulletin to apply. - If determined the passenger seatback frame will be replaced: - The headrest, seatback pad, seatback frame bolts, and side airbag nuts must also be replaced. - The seatback trim and seatback board will be reused. - Do not replace the seat cushion and frame assembly or complete seat assembly. See this bulletin for further detail.
NTB98018G2021-05-10. Service bulletin. ELECTRICAL SYSTEM. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
NTB12060B2021-05-10. Service bulletin. SUSPENSION. SERVICE INFORMATION If a customer would like to activate a subscription for any of the following services: - SiriusXM Satellite Radio, NavTraffic, NavWeather, Travel Link Weather OR If a radio is replaced for any reason, and a customer has an active subscription to any of the above services, OR If a customer claims to have an active subscription to any of the above services, AND any portion of the subscribed service is not operating, ... follow the steps in this bulletin to activate/refresh the service.
NTB130392021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
NTB130382021-05-10. Service bulletin. VEHICLE SPEED CONTROL; SEAT BELTS. SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.
NTB99001A2021-05-10. Service bulletin. SUSPENSION. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
NTB11012B2021-05-10. Service bulletin. STRUCTURE. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
NTB12093A2021-05-10. Service bulletin. POWER TRAIN. IF YOU CONFIRM: After having been parked overnight in ambient temperatures between 5°C to -25°C (40°F to -14°F) the vehicle is hard to start or cranks and will not start. And * Occurs only on first attempts to start before engine begins running. And * Will not occur after engine has been started and run for any period of time. ACTIONS: * Confirm this bulletin applies and if so reprogram the ECM. See this bulleitn for further details.
NTB11044A2021-05-10. Service bulletin. WHEELS. SERVICE INFORMATION To increase tire/wheel assembly balancing accuracy, proper steps should be followed - Make sure to use the correct size wheel centering collet (do not use a cone). - Make sure to use a flange plate and stud set to secure the tire/wheel assembly on the balancer (do not use a cup). - Perform proper wheel mounting and centering checks. See this bulletin for further detail.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.