Service bulletins for the 2022 Nissan Frontier
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
115 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Lighting are shown. Show all
| NTB21-019C | 2024-01-09. Service bulletin. INTERIOR LIGHTING; STRUCTURE. FRONT MAP LAMP NOT WORKING OR SWITCH COMING APART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
|---|---|
| NTB03-074Q | 2023-05-05. Service bulletin. EXTERIOR LIGHTING. HEADLAMP, FOG LAMP, OR REAR COMBINATION LAMP FOGGING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB21-019B | 2023-04-10. Service bulletin. EXTERIOR LIGHTING; STRUCTURE. FRONT MAP LAMP NOT WORKING OR SWITCH COMING APART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| REVISION 1 PC929 | 2023-02-08. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING. Stop Lamp CHMSL Harness Dealer Inventory UPDATE January 19, 2023 Please discard earlier versions of this bulletin. The announcement from January 18, 2023 has been revised to include the following: • The part number for Terminal Joint (Red Solder Sleeve) has been revised: • The revised part number is 24HRK-9002R Solder Sleeve Red (Package of 25 Sleeves) o A single package of sleeves can remedy approximately 6 vehicles • This remedy requires four (4) solder sleeves per vehicle repaired • Note: Claim reimbursement is per solder sleeve unit used in each vehicle repair • Part number 25320-3KA0A Clip has been removed and is not required for this remedy |
| PC929 2022-23 Fr | 2023-02-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Stop Lamp CHMSL Harness Dealer Inventory *****Dealer Announcement***** Nissan is conducting a dealer inventory quality action to add a relay to the stop lamp CHMSL harness and reprogram the ABS control module on specific MY2022-2023 Nissan Frontier vehicles identified in Service Comm and National Service History – Open Campaigns to prevent against a potential no start condition. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. *****What Dealers Should Do***** PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History – Open Campaigns I.D. PC929 • New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). • Refer to NPSB 15-460 for additional information • Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3. Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4. Once remedied, dealers should submit the applicable warranty claim for the action performed to close the campaign notice in Service Comm/NSH and release the vehicle for sale. |
| NTB22-084 | 2022-10-07. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. DTC C1116 AND/OR C1142 STORED IN THE ABS CONTROL MODULE IF YOU CONFIRM Customer states the ABS warning light is ON and “System fault See Owner’s Manual” appears in the message center (Figure 1), AND DTCs C1116 (Stop Lamp Switch) and/or C1142 (Press Sen Circuit) are stored in the ABS Control Module. ACTION Follow the SERVICE PROCEDURE in this bulletin to: 1. Install the Center High Mount Stop Lamp (CHMSL) Relay and Jumper Harness. 2. Install a new Stop Lamp Switch. 3. Reprogram the ABS Control Module. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.