WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Nissan Altima

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

323 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Body and frame are shown. Show all

Bulletins, newest first
NTB09-131C2026-04-29. Service bulletin. STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB09-131C2026-04-29. Service bulletin. STRUCTURE:BODY. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB13-028H2023-03-07. Service bulletin. VISIBILITY; STRUCTURE. REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081J2023-03-07. Service bulletin. VISIBILITY; STRUCTURE. WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB17-0812017-10-25. Service bulletin. STRUCTURE:BODY:TRUNK LID. THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED IF YOU CONFIRM Intermittently, the theft alarm triggers (horn sounds and lights flash) when one of the following occur: - Using the lock, unlock, or trunk open function on the Intelligent Key - Pushing a handle request switch (door or trunk) - Opening a door or the trunk with the vehicle unlocked and CONSULT-III plus (C-III plus) shows the last item to trigger the theft alarm is BATTERY. - Refer to Check Last Item to Trigger Theft Alarm on the next page. ACTION Replace the Body Control Module (BCM). - Refer to the Electronic Service Manual, section BCS-Body Control Systems, for replacement information. - Use the new BCM listed in the PARTS INFORMATION section.
NTB16-1192017-08-01. Service bulletin. STRUCTURE:BODY; EQUIPMENT. 2013 ? 2016 ALTIMA; RUST AROUND REAR LICENSE LAMP FINISHER IF YOU CONFIRM When rust is found on the rear deck lid surface in the area surrounding the license lamp finisher (Figure 1) or replacing the license lamp finisher for any reason. ACTION - Replace the license lamp finisher with the new replacement part listed in the Parts Information. - Refer to the Electronic Service Manual (ESM), section EXT ? Exterior for removal and installation information. - Repair any damaged surfaces that were in direct contact with the license lamp finisher.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.