Service bulletins for the 2025 Mercedes-Benz CLE
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
77 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| LI54.10-P-073164 | 2026-03-10. Service bulletin. ELECTRICAL SYSTEM. Complaint Yellow information message in driver display (instrument cluster): "Switch on motor to charge the 12V battery" Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: • If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% – a negative charge balance • A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. • An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use. |
|---|---|
| LI46.15-P-070510 | 2026-03-10. Service bulletin. STEERING. Complaint Noises from the area of the steering column. - Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. • Instrument panel support • Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: • Position of height and longitudinal adjustment when the noise occurs • If possible, locate affected component part on steering column • State any change in the noise when steering column component parts are touched (e.g. spring, etc.) |
| LI54.71-P-079104 | 2026-02-28. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q4 2025 to early Q1 2026 to rectify concern. |
| LI54.65-P-080132 | 2026-02-28. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI82.90-P-080159 | 2026-02-28. Service bulletin. STEERING. Complaint Stored DTC C220564 - "There is an internal fault in the steering angle sensor. There is an implausible signal." In the quick test, there are also no other DTC's in other control units that point to or reference N80 Steering Column Control Module ("SCCM"). There is no effect on any other components or vehicle functions and it does not cause an instrument cluster light. Cause The DTC only ever occurs during initialization (initialization occurs after bus sleep). The SCCM then resets itself. Remedy 1. If the error is stored and no other control unit points to the N80 SCCM – ignore and erase. Software expected in Q4 2026. 2.If the DTC is in the N80 SCCM AND the following DTC's are in N30/3 (Electronic Stability Program) and N68 (Electric Power Steering): • N30/3 ESP: U071286, Steering column tube module control unit has a malfunction. There is an incorrect signal. • N68 EPS: U042986, Implausible data were received from the steering column module. There is an incorrect signal. Please open a TIPS case to the Body/Chassis/Entertainment inbox. |
| LI72.20-P-075746 | 2026-02-28. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM. Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button being activated accidentally or unintentionally. The recoding can be carried out as follows: 1. Add SA Code O19 into VeDoc (O for Oscar, not "zero") • an XSS ticket may be necessary to add the SA code 2. Perform SCN coding of EIS N73 control unit 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key in the storage compartment on the key symbol and turn on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1 double-click on the locking button As of modification year 22/1, by pressing and holding the locking button + double-clicking on the release tab On model series 167, the storage compartment with the key symbol is located in the armrest. The SCN coding from the EZS is only transferred correctly to the vehicle key under the following conditions: Only one vehicle key is located in the vehicle, this key has been deactivated and it is positioned on the marking in the storage compartment for the data transfer. The costs for this adaptation are to be borne by the customer. |
| LI54.65-P-080132 | 2026-02-14. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI49.10-P-080201 | 2026-02-06. Service bulletin. ENGINE. Complaint Check engine light illuminate, or previously on One of the below Exhaust Flap fault codes stored in PTCU N127: P13C273 P13C278 P140473 Cause Various Remedy Model year 2024 254 and 167 with engine M254 -Update software of N127 PTCU. New software: 254- A2549022611 167- A2549022811 -Clear fault codes and check operation of the exhaust flap. Models with M256, or models with M254 after SW update -Check exhaust flap for free movement via actuation. -Remove flap actuator and check movement of flap in exhaust pipe. Replace exhaust pipe section if flap is binding. -Replace flap actuator if above checks are ok. If fault code returns after performing the above steps, open a TIPS case with the powertrain team. Note: Codes P13C273 and P13C278- Right side flap Code P140473- Left side flap |
| LI32.25-P-079706 | 2026-01-31. Service bulletin. SUSPENSION. Complaint: Clattering noise from area of hood with steel suspension. Cause: Missing helical spring shim (blue part as shown in attached picture "Helical Spring Shim"). Remedy: Check whether the blue helical spring shim is installed. If NOT present: Install the spring shim. Replacement part is black. If present: Replace the blue shim with the aftersales part black shim. If noise is still not remedied after replacing shims, provide sound/video file to the Body, Chassis and Entertainment inbox. |
| LI54.65-P-080132 | 2026-01-31. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION: WARNINGS. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| OTA - 5497150 | 2026-01-31. Over-the-air update. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the software for the Headlamp Range (HLI) control unit does not correspond to the latest series production configuration. As a result, adaptive lighting functions may not be available. Additionally, the following instrument cluster message may appear: "Adaptive High Beam Assist is not available" or "Digital Light: Functionality limited" MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. |
| LI46.15-P-070510 | 2026-01-27. Service bulletin. STEERING. Complaint Noises from the area of the steering column. - Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. • Instrument panel support • Steering column switch module If noise only occurs when adjusting the steering column via electric actuation please perform: 1. Disassemble bellows of steering column tube module. 2. Move steering column entirely out and entirely down. 3. Grease steering column on green-marked positions with a suitable brush (find pictures in attachment). 4. Move column up 1/4 of the way and grease again. 5. Continue until upper limit stop is reached. 6. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 7. If noise does not resolve, perform above procedure again. 8. Then move steering column adjustment in all directions from limit stop to limit stop several times to work in the grease. 9. If noise still does not resolve, please open a TIPS case. For all other noises or if the above does not resolve, create a TIPS case Body, Chassis, and Entertainment inbox. Attach a detailed description of the noise complaint, images, and a recording of the noise. A detailed description includes: • Position of height and longitudinal adjustment when the noise occurs • If possible, locate affected component part on steering column • State any change in the noise when steering column component parts are touched (e.g. spring, etc.) |
| LI00.01-P-078887 | 2026-01-23. Service bulletin. UNKNOWN OR OTHER. Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • IPD = Injector Performance Data • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • P3 Hybrid = AMG Plug-in Hybrid with rear drive unit • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465, 906 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) • 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" • 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • 174 |
| OTA - 5497909 | 2026-01-22. Over-the-air update. ELECTRICAL SYSTEM. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that in certain subject vehicles, the software for the central display control unit does not correspond to the current series production configuration. A remote software update is planned for the central display control unit to increase robustness of the touch screen as well as enhance the touch system functionality/sensitivity. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. |
| LI83.30-P-079850 | 2026-01-22. Service bulletin. VISIBILITY/WIPER. Complaint Customer states the AC either does not cool/has poor performance or heat is insufficient. Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern • Confirm the issue reported by the customer. Compare to Like Vehicle • Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players • Identify the diagnostic strategy and involved components/systems. Testing • Perform relevant diagnostic tests. Refrigerant Quantity • Record the amount of refrigerant recovered and compare it to the specified value (if applicable). • Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings • High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) • PPM of any leaks found. XENTRY Printouts • Climate control AVs. • HV compressor AVs (for heat and AC systems). Thermometer Readings • Left and right dash vents. • Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions • Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings • High and Low pressure readings before and after repairs. Thermometer Readings • Left and right dash vents before and after. • Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation • Complaint Analysis, Game/Players, and Testing Steps. • Include expected results and technical justification for the diagnosis. • Avoid listing R/I steps—focus on diagnostic reasoning and root cause. • All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour) |
| LI83.30-P-079850 | 2026-01-16. Service bulletin. VISIBILITY/WIPER. Complaint Customer states the AC either does not cool/has poor performance or heat is insufficient. Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern • Confirm the issue reported by the customer. Compare to Like Vehicle • Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players • Identify the diagnostic strategy and involved components/systems. Testing • Perform relevant diagnostic tests. Refrigerant Quantity • Record the amount of refrigerant recovered and compare it to the specified value (if applicable). • Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings • High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) • PPM of any leaks found. XENTRY Printouts • Climate control AVs. • HV compressor AVs (for heat and AC systems). Thermometer Readings • Left and right dash vents. • Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions • Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings • High and Low pressure readings before and after repairs. Thermometer Readings • Left and right dash vents before and after. • Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation • Complaint Analysis, Game/Players, and Testing Steps. • Include expected results and technical justification for the diagnosis. • Avoid listing R/I steps—focus on diagnostic reasoning and root cause. • All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour) |
| LI80.35-P-080195 | 2026-01-14. Service bulletin. ELECTRICAL SYSTEM. Complaint "Key Not Detected" message appears on the IC while driving even though the key is in the car and no doors have been opened. Cause Possible SW Remedy Confirm that the message is not due to the driver's door being opened and that the door latch is reading properly. For vehicles that do not have the above issues, there is SW in development. Current workaround is to ensure that the key is left on the antenna in the storage compartment. |
| LI83.30-P-079850 | 2026-01-09. Service bulletin. VISIBILITY/WIPER. Complaint Customer states the AC either does not cool/has poor performance or heat is insufficient. Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern • Confirm the issue reported by the customer. Compare to Like Vehicle • Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players • Identify the diagnostic strategy and involved components/systems. Testing • Perform relevant diagnostic tests. Refrigerant Quantity • Record the amount of refrigerant recovered and compare it to the specified value (if applicable). • Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements Cooling Capacity Test (If System Has a Charge) Before Repairs Gauge Readings • High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) • PPM of any leaks found. XENTRY Printouts • Climate control AVs. • HV compressor AVs (for heat and AC systems). Thermometer Readings • Left and right dash vents. • Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions • Temperature and humidity from OCP AVs (if available). After Repairs - Warranty Submission Requirements on the Repair Order Gauge Readings • High and Low pressure readings before and after repairs. Thermometer Readings • Left and right dash vents before and after. • Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation • Complaint Analysis, Game/Players, and Testing Steps. • Include expected results and technical justification for the diagnosis. • Avoid listing R/I steps—focus on diagnostic reasoning and root cause. • All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found |
| LI82.62-P-080185 | 2026-01-05. Service bulletin. ELECTRICAL SYSTEM. Complaint After updating the CIVIC206 control unit (A26/17), the front Parktronic beep is now only faintly audible and noticeably quieter than the rear beep when reversing. Cause SCN coding in CIVIC206 control unit A26/17 Remedy SCN code control unit A26/17 head unit. |
| LI54.65-P-080132 | 2025-12-15. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI54.71-P-079104 | 2025-12-15. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q4 2025 to early Q1 2026 to rectify concern. |
| LI82.85-P-079530 | 2025-12-15. Service bulletin. ELECTRICAL SYSTEM. Complaint The following most common complaints may be observed: • Brief connectivity interruptions when using Apple CarPlay over Wi-Fi • Audio cuts out • Device not recognized • No operation possible Cause There are multiple possible causes for an iPhone disconnecting from a vehicle’s head unit while using Apple CarPlay. These include hardware, software, and environmental factors: Environmental Interference: External Sources: • Passing under toll bridges, driving near airports, or areas with heavy electronic interference can cause connection drops. Cellular Networks: • Interference from nearby cell towers operating on similar frequencies (usually 2.4GHz or 5GHz) can disrupt the signal. Storage Location: • Keeping your phone in a handbag or surrounded by other objects inside the vehicle can create physical or electronic interference. Device and Software Topics: Head Unit Software/Hardware: • Hardware causes or outdated firmware in the vehicle’s head unit can prevent a stable connection. iPhone Software/Hardware: • Similar causes in the iPhone, including outdated iOS versions or hardware causes, may affect performance. Reset or Reboot: • Automatic rebooting or resetting of either the head unit or the iPhone will temporarily disrupt CarPlay. Connection and Settings: Wired Connections • Cables: A compromised or poor-quality iPhone-USB cable can cause intermittent or total loss of connection. • USB Ports: Dust, debris, or physical deformation in the USB port of either the head unit or the iPhone can also lead to disconnects. Wireless Connections: • Intermittent Bluetooth/Wi-Fi: Unstable wireless communication (Bluetooth/Wi-Fi) can frequently break the Car- Play connection. Power Management: • Battery Saver Mode: Enabling low power mode may restrict background processes, affecting CarPlay. • Vehicle’s Electrical System: Unstable power delivery from the car’s battery or electrical interruptions can cause the head unit to malfunction. Phone & App Configuration: Phone Settings: • Settings (especially Bluetooth or Wi-Fi) on your iPhone can interfere with the CarPlay link. Third-Party Apps/Profiles: • Installed apps or configuration profiles may conflict with CarPlay’s operation. • Native apps are apple maps, apple music, audio books, apple news, podcasts, messages and phone. All other apps are considered third party apps. App Conflicts: • Running conflicting apps that require similar system resources as CarPlay can cause instability. Mobile Data Plan: • Streaming from online sources without sufficient mobile data can result in lost connectivity. Other Factors: Heat & Overheating: • If either the phone or the head unit overheats, they may disable certain functions to prevent damage, leading to disconnection. User Actions: • Accidentally disconnecting the device in settings, or physically moving or bumping the phone or cable, may disrupt the connection. Remedy Guided Diagnostic Path for Apple CarPlay Connection Issues Please follow the steps below to systematically diagnose and resolve CarPlay concerns: Update Devices: • Ensure the iPhone is updated to the latest available iOS version. • Ensure the vehicle’s head unit is updated to the latest software version available. Isolate the Issue: • Check whether the symptom persists with another iPhone running the latest iOS version. • Test both wireless and wired CarPlay connections: • Does the issue only occur with wireless CarPlay? • Does the wired connection to the phone function correctly? Further Troubleshooting Steps: • Reboot the iPhone. • Reboot the head unit via the settings menu (user data reset). • Remove saved CarPlay connections • Delete the head unit information from the iPhone (see attached video for guidance). • Delete the iPhone from the head unit’s list of paired devices. • Remove the head unit entry from CarPlay settings on the iPhone. • Re-initiate pairing between the head unit and the iPhone to establish a new connection certificate. See attachment for complete text. |
| LI46.80-P-080054 | 2025-12-12. Service bulletin. SUSPENSION. Complaint An instrument cluster message "Rear axle steering fault, stop immediately" is very briefly illuminated in the instrument cluster upon vehicle start-up, prior to driving. No fault codes stored in the rear axle steering control unit N68/4. Cause Asynchronous start-up of control units in the vehicle. Remedy The message clears once the head unit receives the rear axle steering signal. Perform a software update to A26/17 control unit - MBUX multimedia system + instrument cluster (head unit) CIVIC206; the software version must be at least 333.8. NOTE: To verify the head unit is on the correct software version: • Navigate to A26/17 (Head Unit) Control Unit Log. • Locate "Control Unit Specific Data" near the bottom. • Verify "E-Stand" number is at least 333.8. |
| LI82.85-P-080094 | 2025-12-04. Service bulletin. ELECTRICAL SYSTEM. Complaint Displayed Message: “Driver camera not functioning, see Operator’s Manual” Cause Interior temperature too high due to: • Summer heat • Direct sunlight • Lack of air conditioning or ventilation Camera enters self-protection mode to prevent overheating. Remedy Do NOT replace any parts. The driver camera (NTG7: MDC295; CIVIC.i2: CIVIC206) is operating as designed. Allow the interior to cool down. If the message remains after cooling: • Run XENTRY Diagnosis • Check latest software for Actuation of Driver Camera (A26/17) No TIPS case required. |
| LI33.30-P-056665 | 2025-11-20. Service bulletin. POWER TRAIN. Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see picture file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir or shake it well (for at least 1 minute). |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.