Service bulletins for the 2026 Mercedes-Benz AMG GT
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
100 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| LI33.20-P-078406 | 2026-04-17. Service bulletin. SUSPENSION. Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements and/or Creaking/crackling noises from the area of the wheel bearing on the front axle when cornering/ maneuvering. Sound file attached for comparison. MUST match noise for proper diagnosis. NOTE: Steering functionality is not affected. Cause Contact area between wheel bearing and steering knuckle. See also: LI35.30-P-058566 (Axle Half Shaft noise when changing direction - Front) LI33.30-P-056665 (Axle Half Shaft noise when changing direction - Rear) LI40.10-P-059248 (Wheel cracking noise when cornering) Remedy 1. Perform Operation A and evaluate by testing vehicle. 2. If noise is still present after re-testing: • If 192/232 chassis, verify FIN is in the listed range below in "Operation B" and perform. • If not 192/232 chassis or vehicle is a 192/232 not in the listed FIN range, additional verifications of where the noise is coming from are needed. Use multiple channel NVH method to narrow down location. Verify the LI's listed above were completed or if there are other similar noises associated with the chassis (Example: 192/232 also has under panel noises and an associated LI). Operation A: 1. Clean contact surfaces of wheel bearing and steering knuckle with brake cleaner (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: The front area of the wheel bearing and the seals must not come into contact with the cleaner, otherwise, the sealing rings will be damaged. 2. Clean threads of wheel bearing mounting. 3. Thinly coat contact surfaces of wheel bearing, steering knuckle, and axle mating face with Molykote (annular joint grease) (see areas marked blue in pictures "2.jpg" and "3.jpg"). NOTE: Axle mating face greasing is also covered in LI35.30-P-058566 and LI33.30-P-056665. Operation B (Only applies to 192 and 232 in listed FIN range): Only affects vehicles up to FIN end number: • Model series 192: xxx xxx xx 002 876 • Model series 232: xxx xxx xx 022 312 1. Replace steering knuckle. 2. Wheel bearings do not need to be replaced. |
|---|---|
| LI54.71-P-079104 | 2026-04-10. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q2 2026. |
| LI07.70-P-078293 | 2026-04-10. Service bulletin. ENGINE. Complaint Customer states CEL ON with no drivability complaints Cause The following DTC is active and/or stored in the ME (N3/10) due to signal interference: P2B7B26 - Pressure sensor pressure switch 3 of the evaporative emission control system has a short. Remedy Twist the wiring from the ME (N3/10) to the evap pressure sensors. See attached work instructions. |
| LI00.01-P-078887 | 2026-03-28. Service bulletin. UNKNOWN OR OTHER. Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • IPD = Injector Performance Data • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • P3 Hybrid = AMG Plug-in Hybrid with rear drive unit • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 • 906 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465 • 907 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) Star 3.5 • 174 • 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" • 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • 174 • 178 |
| LI82.85-P-080359 | 2026-03-19. Service bulletin. ELECTRICAL SYSTEM. Complaint Mercedes me connect services inoperative (me-Call, Remote Status, etc.). Mercedes me services - activation not possible Notes: - The event code "B16AC00 - The configuration of the SIM card is erroneous" is active and stored - The head unit shows no internet connection Cause The RAMSES module may be faulty. This fault profile can be recognized as follows: With XENTRY Diagnosis, enter the "ACTUAL values" menu of the RAMSES control unit and read out the values with position 175 and 727. ACTUAL values in the event of a fault: Type of mobile service (position 175): No reception Operating mode (position 727): Ready mode Remedy If B16AC00 is permanently active and saved and position 175 is no reception and position 727 is ready mode, it is highly likely that the communication module is faulty. In this case, an initial start up must be carried out. If the problem persists even after an initial start up, please create a TIPS case. |
| LI82.85-P-078722 | 2026-03-17. Service bulletin. ELECTRICAL SYSTEM. Complaint The vehicle's position on the map is displayed far away from its actual position, e.g. the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly. |
| LI54.65-P-080132 | 2026-03-17. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| NCU - 2025120009 | 2026-03-14. Service campaign. ELECTRICAL SYSTEM; POWER TRAIN. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the drivetrain control unit does not meet current production specifications. The system may experience an excessively high quiescent current draw on the vehicle, which could lead to an increased discharge of the 12V battery. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the drivetrain control unit software. |
| LI67.30-P-080343 | 2026-03-11. Service bulletin. STRUCTURE:BODY. Complaint Wind noises in the area of the mirror triangle on the front doors/side window panes Cause Potential causes: • Adjustment of the side window panes • Adjustment of the doors • Influence of seals • Influence of assembly Remedy • If the wind noises only occur on one side: Perform comparison of right/left of the window and door adjustment • If necessary, correct window and door adjustment according to WIS. For the windows, observe the insertion depth in the Z position and the Y position on the mirror triangle in particular. • Check inner seal for deformations. To do so, observe attachment 1 and attachment 2. If a deformation (waviness) can be ascertained: Replace seal or reform back into place using heat and fix in place using cold. • Check outer sealing rail to vertical sealing lip of the mirror triangle. To do so, observe attachment 3. If the sealing rail collides with the vertical sealing lip of the mirror triangle: Either route it such that it rests above the vertical sealing lip of the mirror triangle or shorten. • Check external sealing rail for correct assembly. To do this, ensure that it is engaged into the three existing mounting straps on the door. See Attachment 4. Also ensure that the outer sealing rail is correctly positioned in the x-direction and closes off flush. See Attachments 5 and 6 for this. Also ensure during assembly that the outer sealing rail is inserted beneath the mirror triangle. See Attachment 7. • Check the inner seal, especially in the mirror triangle area, for correct assembly. See Attachment 8. |
| LI88.50-P-080263 | 2026-03-11. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM. Complaint The trunk lid does not open or close completely and must be operated manually by the customer. The following fault codes are stored in the Tailgate Control (HKS) control unit: P1CA000 & B188C2A Cause If the trunk lid is repeatedly opened manually or the vehicle has experienced undervoltage, the trunk lid loses its normalization due to faulty software coding. Remedy For vehicles with a production date up to 01/22/26 (232) or 01/27/26 (192): Update the HKS N121/1 control unit and perform SCN coding. • If no new software is available, perform SCN coding. Vehicles with a production date 01/22/2026 (232) or 01/27/2026 (192) and later have already received the correct QNT from the factory. |
| LI82.10-P-078301 | 2026-03-11. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304 |
| LI54.10-P-073164 | 2026-03-10. Service bulletin. ELECTRICAL SYSTEM. Complaint Yellow information message in driver display (instrument cluster): "Switch on motor to charge the 12V battery" Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: • If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% – a negative charge balance • A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. • An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use. |
| LI54.21-P-080326 | 2026-03-10. Service bulletin. ENGINE. Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer. There is software in development for this concern. |
| LI54.71-P-079104 | 2026-02-28. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q4 2025 to early Q1 2026 to rectify concern. |
| LI54.65-P-080132 | 2026-02-28. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI54.10-P-069698 | 2026-02-28. Service bulletin. ELECTRICAL SYSTEM. Complaint This LI does Not apply to 223 or 206 which use a different generation of 48V systems. Please follow the relevant guided tests for the 223 and 206. For 223 with fault code B1FCB97 follow LI54.10-P-076026. Various causes are possible. The faults listed in the various causes do not all have to be present at all times. Some of these complaints may overlap. Rely on the faults listed in the Cause section for identifying the correct Remedy. 1. No start 2. Yellow or red instrument cluster message for 48 V on-board electrical system battery (G1/3) 3. Limp home mode, overheating, A/C not blowing cold, or loss of acceleration 4. Check Engine Light Cause Cause 1: Software causes Intermittent No Starts with fault B183387 in DC/DC converter N83/1 Cause 2: Software causes Permanent No Start with fault B183349. May also have fault B183371. Cause 3: Hardware short circuit in 48V system causes fault B183319 in 48V battery. May also have fault B183371. Cause 4: Internal 48V battery Peltier cooling element failure causes fault B183397 Cause 5: This will Always have fault code B183371 but different from cause 2 and 3 -- it will Not have B183349, B183319, or any other faults in the 48V battery. This will only have fault B183371 in 48V battery. Cause 5 is from the 48V battery detecting an abnormality which then causes the 48V battery to disconnect itself. The disconnected 48V battery then causes subsequent symptoms: Limp Home Mode, overheating, A/C not blowing cold, or loss of acceleration Cause 6: Check Engine Light with fault P0606F1 in the N127 PTCU Cause 7: Check Engine Light with possible no start and fault P057FF1 Remedy Note: each of these remedies correspond to a specific cause. Make sure to match correct Cause with Remedy. Remedy 1: 1. Check the 12V power supply and LIN connection 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms Remedy 2: 1. Charge the 12V battery (Charging current <5A) 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms If the faults return or cannot be cleared: 1. XENTRY MUST be connected with VCI cable to correctly complete this remedy. 2. Complete guided test for B183349. 3. If guided test completes, vehicle starts, and drive cycles show no further symptoms, release vehicle. 4. If after guided test completes, XENTRY states to replace 48V battery: replace only 48V battery. If vehicle is a MY21 w/M256 engine, update SW in 48V battery 5. If this is a repeat visit for fault B183349 and guided test has already been completed, open a TIPS case. 6. If guided test does not complete OR symptoms are still present open a TIPS case. 7. If communication cannot be established with 48V battery perform physical layer check at 12V wiring to DCDC. If no abnormalities found, replace the 48V battery. 8. If guided test completes but a new fault code is present (such as B183319, B183371, etc.) follow the relevant Cause/Remedy for that fault in this LI. Remedy for 3: (If this occurred after Campaign 2025050001, this Li does not apply and LI54.10-P-079772 should be followed) 1. If fault is not Current (only Stored): 1. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 2. Road test and release vehicle if no further symptoms If the faults return or this is a second visit after the SW update: 1. Complete the guided test for B183319 2. Perform XENTRY actuations for all 48V components. 3. Create a TIPS case with ALL Preliminary measures required as noted below for Remedy 5 4. Upload to TIPS case ISA performance data from the N129. 5. ISA performance data location in XD: 6. N129 control unit under Special Procedures 7. "Procedures for support queries to market support" 8. "Collation of diagnosis performance data" 9. "engine at idle" See attachment for further instructions. |
| LI82.10-P-078301 | 2026-02-25. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304 |
| LI54.10-P-080053 | 2026-02-19. Service bulletin. ELECTRICAL SYSTEM. Complaint Discharge of 12 V battery in the event of a longer non-operational time - model series 232 and model series 192 Cause Increased quiescent current Remedy 1. Conduct quiescent current measurement. DO NOT USE A DVOM IN LINE - this will blow the fuse in your meter. Use an amp clamp with either a DVOM or XENTRY Scope and wait until the vehicle has gone to sleep (usually takes 6-10 minutes). Once the vehicle is asleep, observe the quiescent current for 10-15 minutes and note down the values. A stable quiescent current should be less than 50 mA. Values higher than this figure are considered not OK (NOK) and require further analysis. 2. If the quiescent current is higher (> 50 to 100 mA): • Check whether software updates are available for relevant control units: Door control units (DMD (N69/1), DMP (N69/2), DMRL (N69/3), DMRR (N69/4)), EIS (N73/3), PTCU (N127), OHCM (N70), GW (N73/3*1) • After installing the updates: measure the quiescent current again • If the quiescent current is < 50 mA, the vehicle is OK • If the quiescent current is between 50 and 100 mA, continue with step 5 • If the quiescent current is between 100 and 200 mA, continue with step 3 • If the quiescent current is between 200 mA and 1 A, continue with step 4 3. For no-load current values of 100 to 200 mA: • Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. • Disconnect door separation points (A-pillar connection) when the vehicle is asleep, starting with the driver's side • Document the quiescent current value • If there is no change: Disconnect the door separation point on the front passenger side and note down the value again • If the quiescent current falls below 50 mA after the door separation point is opened, the respective outer door handle must be replaced • If the quiescent current drops below 50mA, the draw has been addressed and the vehicle can be released • If the quiescent current remains above 50mA after the relevant door handles have been successfully replaced, please create a TIPS case to the LV/HV inbox and retain the removed door handles for the time being • If the quiescent current does not change after the door separation point is opened, please carry out step 5 4. For quiescent current values between 200 mA and 1 A: • Important: Before pulling out F320 and F304, the tow-away protection and interior protection must be deactivated to prevent an alarm from triggering • Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. • Wait until the vehicle has gone to sleep • Pull out the fuses one after the other, starting with F323 (PTCU CU/N127), and note down the quiescent current value • Perform the same test one at a time if the value is still high for each additional fuse: F119 (PTCU CU/N127), F324 (EIS CU/N73/3), F305 (EIS CU/N73/3), F320 (OCP CU/N70), F304 (OCP CU/N70) • If pulling out the fuse reduces the quiescent current to below 50 mA, replace the corresponding control unit. After replacing, please measure and assess the quiescent current again • Please create a TIPS case for information purposes • If the quiescent current remains unchanged after the fuses listed above are pulled out, please carry out step 5 5. If the quiescent current remains above 50 mA after all controls have been implemented: • Create a TIPS case • Document all the completed steps and measurement results • Attach the XENTRY Scope trace of the draws that you have seen and identify where certain steps were taken. • Attach the latest N73 and N73/3*1 CUL's • If the quiescent current is higher than 1 A, the bus keep awake control unit should be identified via the EIS gateway |
| LI07.70-P-078293 | 2026-02-19. Service bulletin. ENGINE. Complaint Customer states CEL active in instrument cluster Cause Under Investigation Remedy Take no action. Replace no parts. Open a TIPS case and include: • Initial quick test with freeze frame • ME control unit log |
| LI54.65-P-080132 | 2026-02-14. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI27.60-P-078998 | 2026-02-13. Service bulletin. POWER TRAIN. Complaint A noticeable jerk or jolt from the transmission occurs in electric driving mode (E mode), between 20-40 mph. Concern is mainly felt when coasting. Cause Parameters of the 5–4 neutral downshift (the shift method used in EV operation). Remedy This shift concern is considered normal for vehicles with this drivetrain. Hardware replacement does not change the root cause of the concern, as the observed shift behavior is characteristic of normal system function rather than a component‑related fault. The following adaptations may improve the shift quality: 1. Check transmission oil level (transmission oil temperature > 60°C) 2. Flush valves via Xentry procedure 3. Perform standstill adaptation 4. Perform driving adaptations for the 5–4 shift while following the below parameters: - Drive program: Slippery - Display torque in the instrument cluster - Do not shift using the paddles During coasting downshift 5-4: - Torque between –90 and –15 Nm (-66 and -11 ft-lb) - Maximum engine speed: 1,300 rpm |
| LI07.70-P-078293 | 2026-02-13. Service bulletin. ENGINE. Complaint Customer states CEL active in instrument cluster Cause Under Investigation Remedy Take no action. Replace no parts. Open a TIPS case and include: • Initial quick test with freeze frame • ME control unit log |
| LI20.10-P-072886 | 2026-02-13. Service bulletin. ENGINE. Complaint CEL on with Code P012800 "The Coolant Temperature is Below the Specified Temperature" Cause Under investigation. This is not an issue that affects drivability or performance and is not a safety concern. The vehicle remains safe to operate with this code, but the measures listed in the "Remedy" section are recommended. Remedy 1. Use VMI to check for Emission Extended Warranty – Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) 2. If the vehicle is covered under the Emission Extended Warranty, Please perform steps outlined in the NCU for repairs. 3. If vehicle does not fall into the covered area of the Extended Warranty please check for Software updates to the ME control unit and then proceed with "Remedy Instructions" in attachments. Due to formatting issues please see "remedy instructions" in attachments |
| LI32.34-P-080258 | 2026-02-10. Service bulletin. SUSPENSION. Complaint "Do Not Drive Over 50MPH" Suspension Message in Instrument Cluster Possible DTC's in Quicktest: C128763 in N51/1 - "The pressure control system has a malfunction. There is an implausible signal." C128864 in N51/1 - "The level control system has a malfunction. The duration of the actuation was exceeded: overload protection is active." Note: Only applies to vehicles up to production date October 15, 2025 Cause Coding in the suspension control unit N51/1 (EHRC232). Remedy SCN code the suspension control unit N51/1 (EHRC232). Verify no instrument cluster light illuminates when actuating the front axle lifter to the raised and lowered position. |
| LI54.71-P-080236 | 2026-02-06. Service bulletin. ELECTRICAL SYSTEM. Complaint Red ring displayed around vehicle when front or rear camera door actuates. Please also see LI54.65-P-080132 for additional listed red ring causes. Cause EMF interference. Remedy Camera functionality is not affected. Cameras and displays operate normally. For vehicles with a front facing actuating camera and flap (223 and 297): • 223, 297 > Install clip on ferrite magnet on M35/1, pin 3. For vehicles with rear facing camera (223, 213 Facelift, 238, 257, 290, 297): • 297 > Install 2 x ferrite magnets on M35/2, pin 3 and 4. • 213 Facelift, 223, 238, 257, 290 > Install on M35/2, pin 4 |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.