Service bulletins for the 2024 Mercedes-Benz AMG GT
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
238 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Transmission and driveline are shown. Show all
| LI27.00-P-075630 | 2024-09-12. Service bulletin. POWER TRAIN. Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LI’s before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise? |
|---|---|
| LI27.00-P-073124 | 2024-07-31. Service bulletin. POWER TRAIN. Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: ·NAG3 Classic (automatic transmission 725.0) ·NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) ·NAG3 - AMG 63 ·NAG3 - Hybrid |
| LI27.10-P-075869 | 2024-07-30. Service bulletin. POWER TRAIN. Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data |
| LI27.60-P-077704 | 2024-07-04. Service bulletin. POWER TRAIN. Complaint DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button Note: Vehicle can still be placed into park by opening driver's door, or turning off ignition. Please refer to operator's manual section, "Engaging park position P," for additional instructions. Cause Possible causes: 1. Contamination/ingress of dust 2. Short circuit due to ingress of water Remedy Clean printed circuit board under plastic housing and button "P": 1. Remove DSI (AR27.60-P-0901FRX) 2. Remove housing of DSI (see picture 1) 3. Remove cover around "P" button above printed circuit board (see picture 2) 4. Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) 5. Check "P" button: Water residues and/or contamination (cf. picture 4) 6. Carefully clean the affected areas (using contact cleaner) 7. Reassemble and check the functionality 8. If fault code still present after rework -- follow available guided test remedy. |
| LI27.60-P-077704 | 2024-05-01. Service bulletin. POWER TRAIN. DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button Note: Vehicle can still be placed into park by opening driver's door, or turning off ignition. Please refer to operator's manual section, "Engaging park position P," for additional instructions. Possible causes: 1. Contamination/ingress of dust 2. Short circuit due to ingress of water Clean printed circuit board under plastic housing and button "P": 1. Remove DSI (AR27.60-P-0901FRX) 2. Remove housing of DSI (see picture 1) 3. Remove cover around "P" button above printed circuit board (see picture 2) 4. Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) 5. Check "P" button: Water residues and/or contamination (cf. picture 4) 6. Carefully clean the affected areas (using contact cleaner) 7. Reassemble and check the functionality 8. If fault code still present after rework -- open TIPS Case |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.