Service bulletins for the 2020 Mercedes-Benz AMG GT
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
245 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| LI00.01-P-078887 | 2026-03-28. Service bulletin. UNKNOWN OR OTHER. Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • IPD = Injector Performance Data • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • P3 Hybrid = AMG Plug-in Hybrid with rear drive unit • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 • 906 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465 • 907 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) Star 3.5 • 174 • 178 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" • 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • 174 • 178 |
|---|---|
| LI82.85-P-078722 | 2026-03-17. Service bulletin. ELECTRICAL SYSTEM. Complaint The vehicle's position on the map is displayed far away from its actual position, e.g. the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly. |
| LI54.65-P-080132 | 2026-03-17. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| NCU - 2025120009 | 2026-03-14. Service campaign. ELECTRICAL SYSTEM; POWER TRAIN. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the drivetrain control unit does not meet current production specifications. The system may experience an excessively high quiescent current draw on the vehicle, which could lead to an increased discharge of the 12V battery. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the drivetrain control unit software. |
| LI82.10-P-078301 | 2026-03-11. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Note: Only implement Remedy 1 for model series 463 (from model year 2018) and model series 465. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304 |
| LI54.10-P-073164 | 2026-03-10. Service bulletin. ELECTRICAL SYSTEM. Complaint Yellow information message in driver display (instrument cluster): "Switch on motor to charge the 12V battery" Cause The state of charge (SOC) of the 12V battery has dropped to 45% or less. Remedy This warning message appears as soon as the state of charge (SOC) of the 12V primary battery drops below 45%. This message is displayed to safeguard the vehicle's starting ability. At the same time as the display appears in the instrument cluster, customers with a linked Mercedes me connect account also receive a push notification via the app/by email (if this function is activated). The battery must be charged to a state of charge (SOC) of at least 50%. To do this, an external charger can be connected (please comply with AR54.10-P-1133S) or the vehicle can be driven (by the customer) for 30 to 60 minutes. Please make customers aware of how the vehicle behaves: • If the vehicle is used for short journeys, the battery state of charge may slowly drop to less than 45% – a negative charge balance • A negative charge balance will also occur if the vehicle is used while stationary without running the engine, e.g. if the head unit is used, the ignition is switched on, or other comfort & convenience power consumers, e.g. seat heating/seat ventilation, are active. • An unlocked vehicle may increase consumption, because certain vehicle functions are actively kept ready for the customer. In combination with Keyless-Go or flush-mounted door handles, the vehicle may be woken up if the vehicle key is detected in the vicinity of the vehicle. The cause of the discharge can be identified with the aid of the onboard electrical system data in the EZS using XENTRY Diagnosis. See attached examples for identifying typical customer situations (e.g. operation with ignition on, operation of head unit while stationary or vehicle unlocked while parked). Vehicles with code B01+801: When charging while stationary, the 48V battery must have a state of charge (SOC) of 70% before the 12V primary battery, or the secondary battery in the case of code 503, can be charged. To ensure optimum battery care, please also comply with the existing Service Information documents regarding the handling of stock vehicles (SI54.10-P-0024A) and on remaining in transport mode (SI54.00-P-0004A) until immediately before handover to end customers. Special note: Do not replace any parts, if the message has occurred due to battery discharge as a result of the driving profile or the ignition being switched on (see attached examples); in such cases separate warranty and goodwill invoicing is not possible, as this is a normal on-board electrical system protection function. Likewise battery care and recharging do not qualify as a W&G case. Please advise customers accordingly regarding the above-mentioned issues relating to vehicle use. |
| LI54.21-P-080326 | 2026-03-10. Service bulletin. ENGINE. Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer. There is software in development for this concern. |
| LI54.65-P-080132 | 2026-02-28. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI54.10-P-069698 | 2026-02-28. Service bulletin. ELECTRICAL SYSTEM. Complaint This LI does Not apply to 223 or 206 which use a different generation of 48V systems. Please follow the relevant guided tests for the 223 and 206. For 223 with fault code B1FCB97 follow LI54.10-P-076026. Various causes are possible. The faults listed in the various causes do not all have to be present at all times. Some of these complaints may overlap. Rely on the faults listed in the Cause section for identifying the correct Remedy. 1. No start 2. Yellow or red instrument cluster message for 48 V on-board electrical system battery (G1/3) 3. Limp home mode, overheating, A/C not blowing cold, or loss of acceleration 4. Check Engine Light Cause Cause 1: Software causes Intermittent No Starts with fault B183387 in DC/DC converter N83/1 Cause 2: Software causes Permanent No Start with fault B183349. May also have fault B183371. Cause 3: Hardware short circuit in 48V system causes fault B183319 in 48V battery. May also have fault B183371. Cause 4: Internal 48V battery Peltier cooling element failure causes fault B183397 Cause 5: This will Always have fault code B183371 but different from cause 2 and 3 -- it will Not have B183349, B183319, or any other faults in the 48V battery. This will only have fault B183371 in 48V battery. Cause 5 is from the 48V battery detecting an abnormality which then causes the 48V battery to disconnect itself. The disconnected 48V battery then causes subsequent symptoms: Limp Home Mode, overheating, A/C not blowing cold, or loss of acceleration Cause 6: Check Engine Light with fault P0606F1 in the N127 PTCU Cause 7: Check Engine Light with possible no start and fault P057FF1 Remedy Note: each of these remedies correspond to a specific cause. Make sure to match correct Cause with Remedy. Remedy 1: 1. Check the 12V power supply and LIN connection 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms Remedy 2: 1. Charge the 12V battery (Charging current <5A) 2. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 3. Road test and release vehicle if no further symptoms If the faults return or cannot be cleared: 1. XENTRY MUST be connected with VCI cable to correctly complete this remedy. 2. Complete guided test for B183349. 3. If guided test completes, vehicle starts, and drive cycles show no further symptoms, release vehicle. 4. If after guided test completes, XENTRY states to replace 48V battery: replace only 48V battery. If vehicle is a MY21 w/M256 engine, update SW in 48V battery 5. If this is a repeat visit for fault B183349 and guided test has already been completed, open a TIPS case. 6. If guided test does not complete OR symptoms are still present open a TIPS case. 7. If communication cannot be established with 48V battery perform physical layer check at 12V wiring to DCDC. If no abnormalities found, replace the 48V battery. 8. If guided test completes but a new fault code is present (such as B183319, B183371, etc.) follow the relevant Cause/Remedy for that fault in this LI. Remedy for 3: (If this occurred after Campaign 2025050001, this Li does not apply and LI54.10-P-079772 should be followed) 1. If fault is not Current (only Stored): 1. Update software in G1/3 (48V battery) using newest XENTRY software and Add-ons 2. Road test and release vehicle if no further symptoms If the faults return or this is a second visit after the SW update: 1. Complete the guided test for B183319 2. Perform XENTRY actuations for all 48V components. 3. Create a TIPS case with ALL Preliminary measures required as noted below for Remedy 5 4. Upload to TIPS case ISA performance data from the N129. 5. ISA performance data location in XD: 6. N129 control unit under Special Procedures 7. "Procedures for support queries to market support" 8. "Collation of diagnosis performance data" 9. "engine at idle" See attachment for further instructions. |
| NCU - 2024100016 | 2026-02-27. Emissions. ENGINE; ELECTRICAL SYSTEM. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz, has determined that on certain MY 2019-2021 G-Class, S-Class and GT (463, 222 & 190 platforms) vehicles, the engine control unit software does not correspond to current production specifications. It is therefore possible that onboard diagnostics and/or exhaust gas emissions requirements may not be fulfilled. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will perform the ECU software update. |
| LI82.10-P-078301 | 2026-02-25. Service bulletin. EXTERIOR LIGHTING. Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps: 1. Drive vehicle into workshop (temperature higher than +18 °C/+64.4 °F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing of fogged/condensed LED headlamps and LED rear lamps on electric vehicles: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). 2. Connect battery backup via a charger. 3. Open the front-end flap and ensure sufficient ventilation. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4°F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in condensation, check the headlamp for malfunctions. (see Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A defective headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness according to LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. Note: With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. • Open ventilation system LI82.10-P-078302 • Closed ventilation system LI82.10-P-078304 |
| LI27.19-P-080219 | 2026-02-17. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Complaint Check engine light on with the following fault is current in the VGS Control Unit: P084300 Oil pressure sensor 'A' has a short circuit to positive stored in VGS control unit. Cause Electrical failure of oil pressure sensor integrated into VGS Control Unit Remedy Intelligent Predictive Repair (IPR) recognizes this fault pattern and will provide the necessary repair suggestion. 1. Perform IPR and follow the recommended procedures 2. Replace complete EHS valve body, fill to near max fluid level, & complete initial start-up - Ensure all oil guide pipes are installed in the new valve body to prevent a new concern after replacement. |
| LI54.65-P-080132 | 2026-02-14. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI20.10-P-072886 | 2026-02-13. Service bulletin. ENGINE. Complaint CEL on with Code P012800 "The Coolant Temperature is Below the Specified Temperature" Cause Under investigation. This is not an issue that affects drivability or performance and is not a safety concern. The vehicle remains safe to operate with this code, but the measures listed in the "Remedy" section are recommended. Remedy 1. Use VMI to check for Emission Extended Warranty – Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) 2. If the vehicle is covered under the Emission Extended Warranty, Please perform steps outlined in the NCU for repairs. 3. If vehicle does not fall into the covered area of the Extended Warranty please check for Software updates to the ME control unit and then proceed with "Remedy Instructions" in attachments. Due to formatting issues please see "remedy instructions" in attachments |
| NCU - 2024090007 | 2026-02-13. Service campaign. ELECTRICAL SYSTEM; ENGINE. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the engine control unit software does not correspond to current production specifications. As a consequence, the functionality of the post-catalyst oxygen sensor may be impaired due to increased thermal loading. MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the engine control unit software. |
| LI54.71-P-080236 | 2026-02-06. Service bulletin. ELECTRICAL SYSTEM. Complaint Red ring displayed around vehicle when front or rear camera door actuates. Please also see LI54.65-P-080132 for additional listed red ring causes. Cause EMF interference. Remedy Camera functionality is not affected. Cameras and displays operate normally. For vehicles with a front facing actuating camera and flap (223 and 297): • 223, 297 > Install clip on ferrite magnet on M35/1, pin 3. For vehicles with rear facing camera (223, 213 Facelift, 238, 257, 290, 297): • 297 > Install 2 x ferrite magnets on M35/2, pin 3 and 4. • 213 Facelift, 223, 238, 257, 290 > Install on M35/2, pin 4 |
| LI27.10-P-075869 | 2026-02-04. Service bulletin. POWER TRAIN. Complaint Only vehicles with a variable transfer case are affected. This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units. N45 or N15/7 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present: Process them as per the guided test in Xentry. If no faults are present: 2. Check the transmission oil level If the oil level is correct: 3. Unplug the connector for the transfer cases control unit and reassess the vehicle on a subsequent test drive If the complaint no longer occurs with the control unit disconnected: 4. Perform an oil change of the transfer case according to WIS specifications - Collect an oil sample of the original fluid 5. Complete all transfer case Tech-in processes located under VG Control Unit > Adaptations - Resetting the oil service data - Calibration of N15/7 5. Perform road test of vehicle to bring transmission to operating temperature ( >60C ) 6. Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Return the vehicle to the client and request they drive the vehicle for at least 200 miles and return if the concern is not resolved. The extended drive will ensure the clutches are properly conditioned with the new oil and should resolve the concern. If the concern continues to occur with the control unit disconnected or after the above steps have been performed, please submit a TIPS case to the Powertrain inbox with the following information: - Initial quick test with fault freeze frame data - Initial transmission EEPROM data - VGS and Transfer Case Control Unit Log (N45 or N15/7) - Photo of the original oil condition - What color was the fluid drained from the transfer case before the oil change? - Was an oil sample collected, and can you provide a photo of the original fluid? - What color and part number fluid was used during the oil change? - How far was the vehicle driven after? |
| LI54.65-P-080132 | 2026-01-31. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION: WARNINGS. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide. |
| LI82.85-P-078722 | 2026-01-27. Service bulletin. ELECTRICAL SYSTEM. Complaint The vehicle's position on the map is displayed far away from its actual position, e.g. the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly. |
| LI00.01-P-078887 | 2026-01-23. Service bulletin. UNKNOWN OR OTHER. Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference. Cause Information only Remedy Acronyms: • AV = Actual Values • CU = Control Unit • CUL = Control Unit Log • DTC = Diagnostic Trouble Code • E-Stand = Fresh-up head unit boot software (found in head unit control unit log) • FUP = Fresh-up • FW = Firmware • HSVL = High Speed Video Line • HU = Head Unit • HW = Hardware • IPD = Injector Performance Data • ISU = Initial Start Up • LVDS = Low Voltage Differential Signal • NAG"x" = New Automatic Gearbox ("x" is the generation number, example: NAG3) • NSFT = Not Safe For Transport • MOPF = Model Facelift (Ex: 167 MOPF) • PiH = Plug-in Hybrid • P3 Hybrid = AMG Plug-in Hybrid with rear drive unit • SA Code = Sonderausstattungscode (Option Code) • SCN = Software Calibration Number • SW = Software • TCU = Telecommunication Control Unit (Hermes/Ramses/Etc...) • QT = Quicktest • XD = XENTRY Diagnosis Control Unit Identification: Refer to the attachment "Control Unit Nomenclature" for location of each. • Control Unit Name • Control Unit Number • Control Unit Short name • Control Unit Diogenes ("dy-oj-uh-neez") name - Control unit variant/family. Network/Wiring Architecture to Baumuster Quick Reference: Star 1 • 117, 156, 246 (MFA) • 166, 176, 221, 242, 246, 292 Star 2 • 205, 213, 238, 253, 257, 290 (MRA) • 117, 156, 246 (MFA) • 118, 177, 243, 247 (MFA2) • 167, 222, 292, 463, 465, 906 Star 3 • 294, 295, 296, 297 (EVA2) • 206, 214, 223, 236, 254 (MRA2) • 192 and 232 (MSA) • 907 Platform to Baumuster Quick Reference: MRA = "Mercedes-Benz Rearwheel Architecture": • 205 • 213 • 222 • 238 • 253 • 257 • 290 MRA2 = "Mercedes-Benz Rearwheel Architecture - Generation 2": • 206 • 214 • 223 • 236 • 254 MFA = "Mercedes-Benz Frontwheel Architecture" • 117 • 156 • 246 MFA2 = "Mercedes-Benz Frontwheel Architecture - Generation 2" • 118 • 177 • 243 • 247 EVA1.5 = "Electric Vehicle Architecture" • 243 EVA2 = "Electric Vehicle Architecture - Generation 2" • 294 • 295 • 296 • 297 MSA = "Mercedes-Benz Sport Architecture" • 192 • 232 MMA = "Mercedes-Benz Modular Architecture" • 174 |
| LI83.30-P-079850 | 2026-01-22. Service bulletin. VISIBILITY/WIPER. Complaint Customer states the AC either does not cool/has poor performance or heat is insufficient. Cause Many possible root causes Remedy *Note - This Li does not apply if there are other Li's that apply to your concern OR you have a fault and/or guided test that leads to a root cause. AC Diagnosis (General) Initial Steps Verify Customer Concern • Confirm the issue reported by the customer. Compare to Like Vehicle • Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players • Identify the diagnostic strategy and involved components/systems. Testing • Perform relevant diagnostic tests. Refrigerant Quantity • Record the amount of refrigerant recovered and compare it to the specified value (if applicable). • Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements (Template attached to be used for submission of Warranty claim and/or TIPS case) Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings • High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) • PPM of any leaks found. XENTRY Printouts • Climate control AVs. • HV compressor AVs (for heat and AC systems). Thermometer Readings • Left and right dash vents. • Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions • Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings • High and Low pressure readings before and after repairs. Thermometer Readings • Left and right dash vents before and after. • Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation • Complaint Analysis, Game/Players, and Testing Steps. • Include expected results and technical justification for the diagnosis. • Avoid listing R/I steps—focus on diagnostic reasoning and root cause. • All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour) |
| LI83.30-P-079850 | 2026-01-16. Service bulletin. VISIBILITY/WIPER. Complaint Customer states the AC either does not cool/has poor performance or heat is insufficient. Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern • Confirm the issue reported by the customer. Compare to Like Vehicle • Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players • Identify the diagnostic strategy and involved components/systems. Testing • Perform relevant diagnostic tests. Refrigerant Quantity • Record the amount of refrigerant recovered and compare it to the specified value (if applicable). • Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements/Warranty Claim Submission Requirements Cooling Capacity Test (If System Has a Charge) *Note - TIPS case is only required if the root cause is not identified or other Li's/documents require a case to be open. Before Repairs Gauge Readings • High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) • PPM of any leaks found. XENTRY Printouts • Climate control AVs. • HV compressor AVs (for heat and AC systems). Thermometer Readings • Left and right dash vents. • Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions • Temperature and humidity from OCP AVs (if available). After Repairs Gauge Readings • High and Low pressure readings before and after repairs. Thermometer Readings • Left and right dash vents before and after. • Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation • Complaint Analysis, Game/Players, and Testing Steps. • Include expected results and technical justification for the diagnosis. • Avoid listing R/I steps—focus on diagnostic reasoning and root cause. • All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code (MAX 1 hour) 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found (MAX 1 hour) |
| LI05.20-P-080192 | 2026-01-16. Service bulletin. ENGINE. Complaint Customer states check engine light on in the dash. Vehicle has one or more DTC's Present P164B00, P164B09, P2B4400, P005A07, P005C07, P005A09, P005C09, P003C07, P2B5007, P003C09, P2B5009, P34C200, P34C109, P34C800, P34BE00, P34BD09 Cause Software and Hardware Remedy 1. Check for available Software updates for the Engine Control Unit ME N3/10. Perform update if available. 2. Check part numbers on ALL CAMTRONIC actuators to ensure latest part numbers are installed. 3. A177 982 03 03 and A177 982 17 00 should be replaced by A177 982 19 00 4. A177 982 02 03 and A177 982 16 00 should be replaced by A177 982 18 00 5. Remove engine cover and check for heat damage on the engine cover and wiring harness in the area above the engine compartment bulkhead and near the windshield. 6. In the event of wiring harness damage please open a TIPS case with photos of the harness and include a Lambda Line Graph Test for evaluation. |
| LI83.30-P-079850 | 2026-01-09. Service bulletin. VISIBILITY/WIPER. Complaint Customer states the AC either does not cool/has poor performance or heat is insufficient. Cause Many possible root causes Remedy AC Diagnosis (General) Initial Steps Verify Customer Concern • Confirm the issue reported by the customer. Compare to Like Vehicle • Determine if the behavior is normal by comparing with a similar vehicle. Determine Your Game and Players • Identify the diagnostic strategy and involved components/systems. Testing • Perform relevant diagnostic tests. Refrigerant Quantity • Record the amount of refrigerant recovered and compare it to the specified value (if applicable). • Forming Gas is the ONLY approved leak test method. (DYE is NOT approved) TIPS Case Submission Requirements Cooling Capacity Test (If System Has a Charge) Before Repairs Gauge Readings • High and Low pressure readings (from machine or separate gauges). Leak Detection (if applicable) • PPM of any leaks found. XENTRY Printouts • Climate control AVs. • HV compressor AVs (for heat and AC systems). Thermometer Readings • Left and right dash vents. • Center vent, footwell, and/or rear vents (if concern is localized). Ambient Conditions • Temperature and humidity from OCP AVs (if available). After Repairs - Warranty Submission Requirements on the Repair Order Gauge Readings • High and Low pressure readings before and after repairs. Thermometer Readings • Left and right dash vents before and after. • Center vent, footwell, and/or rear vents before and after (if localized concern). Documentation • Complaint Analysis, Game/Players, and Testing Steps. • Include expected results and technical justification for the diagnosis. • Avoid listing R/I steps—focus on diagnostic reasoning and root cause. • All prior measurements need to be documented on the repair order. OP code usage: 831232 - Max .5 for Cooling Capacity Test 831040 - Only to be utilized if you have a fault code and are actively diagnosing that fault code 831762 - This includes basic leak check 831285 - This can only be used in extenuating circumstances where a leak cannot be found |
| LI20.10-P-072886 | 2026-01-06. Service bulletin. ENGINE. Complaint CEL on with Code P012800 "The Coolant Temperature is Below the Specified Temperature" Cause Under investigation. This is not an issue that affects drivability or performance and is not a safety concern. The vehicle remains safe to operate with this code, but the measures listed in the "Remedy" section are recommended. Remedy 1. Use VMI to check for Emission Extended Warranty – Engine Thermostat (incl. software update) MY19-23, Various Models and Platforms (167, 190, 205, 213, 217, 222, 223, 232, 253, 290, 463) 2. If the vehicle is covered under the Emission Extended Warranty, Please perform steps outlined in the NCU for repairs. 3. If vehicle does not fall into the covered area of the Extended Warranty please proceed with "Remedy Instructions" in attachments. Due to formatting issues please see "remedy instructions" in attachments |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.