WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Mazda MX-5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

522 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
01-022-19-36572019-12-20. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ENGINE AND ENGINE COOLING. There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
MT-004-192019-11-24. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; ELECTRICAL SYSTEM. Some customers may complain about: • Intermittent engine no start • Instrument cluster red security indicator light ON • Engine Start/Start Button Amber indicator light flashing • Battery discharge • Electrical relay buzzing noise • DTC B13D3:94 (Communication error with remote transmitter) stored.This may be caused by: • A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. • An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. • An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicles’s wiring harness may create unusual electrical symptoms.
07-007-19-36382019-11-21. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ENGINE. Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. For 2014-2016 Mazda6 and 2013-2016 (US spec) / 2017 (Mexico spec) CX-5, the CHECK ENGINE light may turn on with DTC P011A:00 (ECT sensor No.1/No.2 performance problem) stored at the same time. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing. To solve this concern, two mass production changes have been implemented. a) The concentration of the coolant has been increased so that the amount of the contained anti-rust additive is higher. b) The composition of the coolant has been changed (the ratio of the anti-rust additive has increased).
MT-003-192019-10-30. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:
MT-002-192019-10-04. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
SA-040-192019-09-23. Service bulletin. STRUCTURE:BODY:HOOD; ENGINE AND ENGINE COOLING. Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
00-003-19-35832019-03-21. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING; EQUIPMENT. In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.
01-008-19-35682019-03-11. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some customer using "Flexible" setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.
01-004-19-35582019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
01-003-19-35572019-02-19. Service bulletin. ENGINE. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.
MT-009-182019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.
MT-009-182018-12-17. Service bulletin. ENGINE AND ENGINE COOLING. If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.
01-016-18-35222018-10-09. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
MT-008-182018-10-09. Service bulletin. ENGINE; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicles?s wiring harness may create unusual electrical symptoms.
MT-008-182018-08-27. Service bulletin. EQUIPMENT:ELECTRICAL; ENGINE. ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing.
MT-007-182018-08-27. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES; ENGINE; ELECTRICAL SYSTEM. ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger that is interrupting the vehicle electrical systems.
SA-029-182018-08-20. Service bulletin. ENGINE AND ENGINE COOLING. IMPORTANT: If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.
SA-026-182018-07-02. Service bulletin. ENGINE. If a vehicle is driven on extremely short trips most of the time (where the engine never reaches normal operating temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Engine oil dilution with fuel occurring under this specific driving condition is normal with direct injection engines. If the vehicle is driven on a longer trip after a lot of short trips (where the engine reaches normal operating temperature), the Check Engine Light may turn ON with DTC P0172:00 (Fuel system too rich).
01-012-18-34742018-07-02. Service bulletin. ENGINE. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.
04-003-18-34552018-05-14. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial check is a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.
01-007-18-34082018-04-23. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Some vehicles may experience a condition where the engine does not start using the normal starting procedure and the doors will not lock/unlock when using a request switch. The engine will start if you touch the backside of the remote (1) to the push button start (2). This may be caused by water running down between the windshield and the dashboard resulting in corrosion of the terminals at connectors C-16 and/or C-04. To correct this issue, shield plates have been attached to the upper dashboard to prevent water from dropping onto these connectors.
MT-021-172018-02-26. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
01-018-15-30702017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P2610 AND P2507 STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. • P2610:00: INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM • P2507:00: PCM BATTERY VOLTAGE LOW INPUT AS A PAST MALFUNCTION, THE CUSTOMER WILL NOT NOTICE IT (NO WARNING LIGHT ILLUMINATED), BUT THE DTC MAY BE FOUND DURING A VEHICLE SERVICE. P2507 IN THIS SITUATION IS ONLY APPLICABLE ON 2016 AND LATER MODELS. THIS IS CAUSED BY THE ENGINE BEING STARTED 3 OR MORE TIMES AFTER A SHORT DURATION OF ENGINE OFF (LESS THAN 15 SECONDS) WITH THE ROOM FUSED REMOVED.
1080M2017-02-23. Service bulletin. ENGINE. IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT.
01-016-16-32202017-02-23. Service bulletin. ENGINE. THERE IS A CONCERN THAT SOME WATER PUMPS ARE BEING REPLACED THAT ARE NOT FAULTY, DUE TO SIGNS OF A VERY SMALL COOLANT LEAK FROM THE BLEED HOLE. THIS SERVICE BULLETIN IS TO INFORM YOU ABOUT THE WATER PUMP SEALING MECHA-NISM AND THE CRITERIA IF REPLACEMENT IS NECESSARY OR NOT.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.