WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Mazda Mazda6

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

516 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
04-007-20-37132020-11-03. Service bulletin. PARKING BRAKE:ELECTRICAL; SERVICE BRAKES, AIR:DISC:PADS; SERVICE BRAKES, HYDRAULIC. Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise. To eliminate this concern, the brake pad material has been changed in order to improve the rust-removing capability.
04-002-20-3643b2020-11-03. Service bulletin. EQUIPMENT; SERVICE BRAKES. Some vehicles may exhibit a groan noise from the front brakes when braking at a very low speed (approximately 6 mph/10 km/h). This is caused by a brake torque variation due to an uneven coating of the brake pad friction material forming on the surface of the disc plate. To eliminate this concern, the surface processing on the disc plate has been changed.
15-003-20-37372020-10-03. Service bulletin. SERVICE BRAKES, HYDRAULIC; VISIBILITY; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:12V/24V/48V BATTERY; STEERING:ELECTRIC POWER ASSIST SYSTEM. Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. • DTC U0420:68 [Forward sensing camera (FSC)]: Error signal received from electric power steering (EPS) control module. For Mazda6 and CX-5, the following error messages may appear in the instrument cluster. • Front camera sensor system malfunction • Forward Smart City Brake Support Malfunction • Driver attention alert system malfunction. This may be caused by the battery voltage falling and the EPS control module failing the initial learning for the steering center position while cranking. The FSC detects the error notified by the EPS control module. To correct this concern, the control software of the EPS control module has been modified while the repair procedure modifies the FSC for earlier repairs in the market.
09-030-20-37402020-10-03. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE. All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda’s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.
SA-063-202020-09-03. Service bulletin. ELECTRICAL SYSTEM. When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.
MT-002-202020-09-02. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; WHEELS. New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.
01-011-20-37342020-09-01. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about an unusual noise coming from the engine compartment for about 20 seconds after a cold engine start. This noise is a normal engine operation for improved exhaust gas emissions. The noise does not indicate a malfunction. ACCELERATED WARM-UP SYSTEM (AWS): All SKYACTIV-G engines adopt AWS to reduce exhaust gas emissions immediately after a cold engine start. AWS increases the engine idling speed and retards the ignition timing for about 20 seconds after the cold engine start to quickly warm up the catalytic converter. The customer may identify the engine sound during the AWS operation as a unusual noise.
MT-001-202020-08-04. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
09-006-20-3673a2020-08-04. Service bulletin. EQUIPMENT. When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
05-003-20-37252020-08-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN; EQUIPMENT; ENGINE. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic.
SA-053-202020-07-03. Service bulletin. POWER TRAIN. When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission.
SA-026-20a2020-07-03. Service bulletin. EQUIPMENT:ELECTRICAL. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
09-015-20-3698b2020-07-02. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the SD card hardware has been changed.
05-001-20-36992020-07-02. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION. Some customers may complain of a shift shock felt when shifting into 3rd, 5th and/or R range with no A/T related DTC stored. The symptom can be temporarily repaired by A/T initial learning procedure, but may recur after multiple driving cycles. Applicable situations: • Shifting up: 2-3, (4-5) • Shifting down: 4-3, (6-5) NOTE:(4-5) and (6-5) are felt more than others due to the gear ratio. • Shifting into R: D-R, N-R, P-R. Improper control logic of the TCM may cause improper learning of R-3-5 brake engaging speed during certain driving situations. To correct this concern, the control logic of the TCM has been modified.
09-015-20-36982020-05-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the SD card hardware has been changed.
06-002-37052020-05-04. Service bulletin. STEERING. Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and right side for RHD vehicle). NOTE: The noise will not occur if the steering wheel is in the center or to the full passenger-side position. The noise is caused when the edge (A) of the inner ball joint (B) gets stuck with the steering gear housing (C).
SA-041-202020-04-06. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.
SA-037-202020-04-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FORWARD COLLISION AVOIDANCE: SENSING SYSTEM: CAMERA. Some vehicles may have one of the following DTCs stored in memory: • C1001:92 - Forward sensing camera (FSC) poor field of view • B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. • In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). • In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.
SA-036-202020-04-06. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. The owner’s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the owner’s manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent.
00-001-20-36892020-04-03. Service bulletin. SERVICE BRAKES, HYDRAULIC; POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
02-004-20-36852020-02-29. Service bulletin. WHEELS. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
SA-030-202020-02-27. Service bulletin. POWER TRAIN. Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration.
SA-026-202020-02-27. Service bulletin. EQUIPMENT. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Audio System, Bluetooth®, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux Voice Command, How to Check Navi SD Card VIN Lock.
SA-011-20a2020-02-27. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.
SA-011-202020-02-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.