WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Mazda Mazda6

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

670 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
01-008-15-30452017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. • P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.
09-016-15-30412017-06-07. Service bulletin. STRUCTURE:BODY:DOOR. SOME VEHICLES MAY EXPERIENCE A RATTLE NOISE FROM THE FRONT DOOR GLASS WHEN DRIVING WITH THE WINDOW OPEN APPROX. 1/2 TO 4 INCHES (1 - 10 CM). THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. TO INCREASE THE HOLDING FORCE, THE SHAPE OF GLASS RUN CHANNEL HAS BEEN CHANGED AND NON-WOVEN PADS HAVE BEEN ATTACHED TO THE GLASS RUN CHANNEL.
05-002-15-3019D2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
01-015-15-3064A2017-05-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 °F (0 °C). • P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM • P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.
09-037-15-30792017-05-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. SOME VEHICLES MAY EXPERIENCE A FUZZY APPEARANCE (TINY CRACKS) AROUND THE EDGE OF THE ACTIVE DRIVING DISPLAY. REPLACE THE ACTIVE DRIVING DISPLAY.
01-023-15-30842017-05-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
03-006-15-30862017-05-31. Service bulletin. WHEELS:HUB. SOME VEHICLES MAY EXHIBIT A GROAN TYPE NOISE FROM THE FRONT WHEEL HUB BEARING WHILE DRIVING AT HIGH SPEED OR WHEN CORNERING. THIS MAY BE CAUSED BY FRONT WHEEL HUB BEARING CORROSION.
15-001-16-31262017-05-30. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; VISIBILITY:WINDSHIELD. SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING 2 SYMPTOMS, EVEN THOUGH THE WINDSHIELD IS CLEAR. UNDER CERTAIN DRIVING CONDITIONS, THE FORWARD SENSING CAMERA (FSC) MAY DETECT A DIRTY WINDSHIELD (NOT CLEAR).OTE FOR CUSTOMER: THE FSC MAY NOT WORK PROPERLY UNDER THE CONDITIONS:•THE WINDSHIELD IS NOT CLEAR. •THE FSC LENS IS NOT CLEAR. •DRIVING IN HEAVY RAIN, DENSE FOG OR SNOW, OR INTO THE SUN. •DRIVING ON A ROAD WITH NO OR BLURRED ROAD LANE MARKINGS. WHEN THE WINDSHIELD BECOMES FOGGY IN THE WINTER TIME OR OTHER COLD WEATHER CONDITIONS AND LDWS/HBC WARN-ING LIGHTS TURN ON, DRIVE WITH THE DEFROSTER ON FOR ABOUT 10 MINUTES. THIS WILL HELP CLEAR THE FOGGY WINDSHIELD AT THE FSC.
02-005-16-3152A2017-05-30. Service bulletin. SUSPENSION:FRONT:STABILIZER BAR. BEGINNING WITH THE CX-5 AND MAZDA6 MODELS, GRIP TYPE FRONT AND REAR STABILIZER BUSHINGS HAVE BEEN INCORPO-RATED FOR NOISE PREVENTION PURPOSES. IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE.
02-010-16-31702017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE:FRAME AND MEMBERS; SUSPENSION:FRONT:SHOCK ABSORBER. SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:•UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)•STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)•THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)•THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.
01-009-16-31722017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
09-016-16-31582017-05-30. Service bulletin. SEATS. AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.
02-009-16-31552017-05-30. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR. SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD.
05-002-16-31292017-05-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. THE NEW SKYACTIV-DRIVE FW6A-EL AT USES “AUTOMATIC TRANSMISSION FLUID (ATF) TYPE: FZ”. ONLY USE “ATF-FZ” TO FILL OR TOP OFF THE FLUID LEVEL. ATF-FZ IS SPECIALLY DESIGNED FOR USE IN THE SKYACTIV-DRIVE SERIES AT. IT IS A LOW VISCOSITY FORMULA WITH LESS FRICTION FOR BETTER FUEL ECONOMY. NOTE: ATF-FZ IS COLORED BLUE FOR EASY IDENTIFICATION. TO CHECK THE FLUID LEVEL, REMOVE THE BOLT, THEN REMOVE THE DIPSTICK. THE DIPSTICK IS MARKED WITH A “FZ” ON SKYACTIV-DRIVE FW6A-EL AT. WHEN FINISHED, INSERT THE DIPSTICK AND INSTALL THE BOLT.
09-003-16-31302017-05-26. Service bulletin. EXTERIOR LIGHTING:TAIL LIGHTS; EXTERIOR LIGHTING:HEADLIGHTS. SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT (HEADLAMP/HEADLIGHT) OR REAR (TAILLAMP/TAIL-LIGHT) COMBINATION LIGHTS. THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMP-TOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.
02-003-15-29902017-05-25. Service bulletin. EQUIPMENT:MECHANICAL. SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT STRUT BEARING (A) WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO UPPER FRONT STRUT BEARING DAMAGE OR IT MAY BE DUE TO STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE: 1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING HAS BEEN CHANGED. 2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. NOTE: THE PISTON ROD NUT (B) REQUIRES REPLACEMENT WHEN THE FRONT STRUT BEARING IS REPLACED.
01-003-15-30142017-05-25. Service bulletin. EQUIPMENT. USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.
09-009-15-30152017-05-25. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF THE VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEEN THE PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH A HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE A HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED AREA TO REMOVE THE STAIN(S).
05-002-15-3019C2017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
02-002-15-3002A2017-05-19. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. AFTER PERFORMING RECALL CAMPAIGN 8014J, OR THE VEHICLE VIN IS NOT APPLICABLE TO 8014J, SOME VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. THIS MAY BE CAUSED BY IMPROPER TIRE AIR PRESSURE DETECTION BY THE TPMS SYSTEM ON CERTAIN TYPES OF ROAD SURFACES.
05-002-15-30192017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
05-002-15-3019A2017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
05-002-15-3019B2017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
SA-041-172017-05-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. PERMANENT DTCS ARE NOW DISPLAYED WITH THE IDS 104 UPDATE. THE PURPOSE OF A PERMANENT DTC IS TO PREVENT CUSTOMERS FROM CLEARING THEM BY DISCONNECTING THE BATTERY CABLE IN ORDER TO PASS A SMOG CHECK. ALL PCM AND TCM DTCS THAT TURN ON THE CHECK ENGINE LIGHT CAN REMAIN AS A PERMANENT DTC. THEY WILL NOT TURN ON THE CHECK ENGINE LIGHT OR CAUSE DRIVABILITY CONCERNS. IF YOU ENCOUNTER A PERMANENT DTC, IGNORE IT AND DIAGNOSE THE CURRENT STORED OR PENDING DTC.
09-022-15-3047B2017-05-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 55.00.750 OR LATER). • NAVIGATION OR OTHER SCREEN TURN BLACK, FREEZE OR REBOOT. • SYSTEM DOES NOT RECOGNIZE USB/SD CARD. • SOME MENU OF MUSIC SOURCE SELECTION IS GRAYED OUT. • WHEN USING THE CALL BUTTON ON THE CELL PHONE TO MAKE A CALL, THE CALL SOUND IS SHORT. • FAVORITES DISAPPEAR. • VEHICLE CURRENT POSITION IS NOT ACCURATE ENOUGH. • REAR VIEW MONITOR DOES NOT SHOW UP ON SCREEN. • TEXT INFORMATION OF HD RADIO IS NOT DISPLAYED WHEN SWITCHING MUSIC SOURCE. • WHEN ASKING FOR CURRENT LOCATION WITH VOICE COMMAND “WHERE AM I?”, THE SYSTEM RESPONDS WITH “YOUR LOCATION IS COMMA.” • CONTACT INFORMATION CANNOT BE LOADED CORRECTLY FROM PHONES OTHER THAN IPHONE. NOTE: MAZDA IS WORKING TO MAKE FURTHER IMPROVEMENTS TO THE MAZDA CONNECT INFOTAINMENT SYSTEM SOFTWARE, AND MAY ISSUE FUTURE SOFTWARE UPDATES TO IMPROVE SYSTEM OPERATION AND PERFORMANCE. SOFTWARE VERSION UPDATES CAN BE FOUND ON MS3 UNDER IDS/INFOTAINMENT.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.