Service bulletins for the 2015 Mazda Mazda6
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
609 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 09-034-15-3068 | 2017-06-07. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST; EQUIPMENT:ELECTRICAL. SOME CUSTOMERS MAY COMPLAIN THAT THE FRONT POWER (DRIVER AND/OR PASSENGER) SEATS DO NOT SLIDE BACK AND FORTH PROPERLY OR THAT THEY MAY BE COMPLETELY INOPERATIVE. THIS CONCERN MAY BE CAUSED BY A FOREIGN OBJECT GETTING STUCK UNDER THE POWER SLIDE UNIT (BELOW) WHILE IN OPERATION. THIS CAN CAUSE MOTOR MOUNTING BRACKET (A) DEFORMATION, RESULTING IN MOTOR CABLE (B) BREAKAGE. TO ELIMINATE THIS CONCERN, THE SHAPE OF THE MOTOR MOUNTING BRACKET (A) HAS BEEN MODIFIED TO INCREASE ITS STRENGTH. |
|---|---|
| 01-016-15-3067 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0421:00 (CATALYTIC CONVERTER SYSTEM) WITHOUT EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY). THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM THAT MAY DETECT FALSE ERROR OF THE A/F SENSOR, RESULTING IN FALSE DETECTION OF P0421. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED. CATALYST MONITOR FUNCTION EXPLANATION • THE PCM MONITORS THE OXYGEN STORAGE AMOUNT PROPORTIONAL TO CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC. • THE PCM STARTS TO MONITOR AFTER RECOVERY (FUEL INJECTION STARTS) FROM FUEL CUT CONTROL. • THE PCM TEMPORARILY CHANGES THE TARGET AIR/FUEL RATIO TO RICH AT FUEL CUT RECOVERY, AND DETECTS THE RESPONSE TIME UNTIL THE HO2S OUTPUT SIGNAL OUTPUTS THE VOLTAGE ON THE RICH SIDE. • IF THE CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC DETERIORATES, THE AMOUNT OF THE TIME UNTIL THE HO2S DETECTS THE VOLTAGE ON THE RICH SIDE IS SHORTER COMPARED TO THE NORMAL PURIFICATION CHARACTERISTIC AS SHOWN. THE PCM DETECTS A CATALYTIC CONVERTER MALFUNCTION USING THIS CHARACTERISTIC. |
| 01-018-15-3070 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P2610 AND P2507 STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. • P2610:00: INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM • P2507:00: PCM BATTERY VOLTAGE LOW INPUT AS A PAST MALFUNCTION, THE CUSTOMER WILL NOT NOTICE IT (NO WARNING LIGHT ILLUMINATED), BUT THE DTC MAY BE FOUND DURING A VEHICLE SERVICE. P2507 IN THIS SITUATION IS ONLY APPLICABLE ON 2016 AND LATER MODELS. THIS IS CAUSED BY THE ENGINE BEING STARTED 3 OR MORE TIMES AFTER A SHORT DURATION OF ENGINE OFF (LESS THAN 15 SECONDS) WITH THE ROOM FUSED REMOVED. |
| 09-030-15-3073 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT. |
| 09-031-15-3076 | 2017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. • TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMER’S PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM. |
| 06-001-15-3054A | 2017-06-07. Service bulletin. STEERING. SOME VEHICLES MAY EXHIBIT AN UNUSUAL THUMPING NOISE FROM UNDER THE FRONT OF THE VEHICLE. THIS NOISE ONLY OCCURS WHEN STARTING TO MOVE THE VEHICLE WHILE THE STEERING WHEEL IS TURNED TO THE FULL LEFT POSITION. NOTE: THE NOISE WILL NOT OCCUR IF THE STEERING WHEEL IS IN THE CENTER OR FULL RIGHT POSITION. THE NOISE IS CAUSED WHEN THE EDGE OF THE LEFT SIDE INNER BALL JOINT GETS STUCK WITH THE STEERING GEAR HOUSING. TO ELIMINATE THE NOISE, THE SHAPE OF THE INNER BALL JOINT EDGE HAS BEEN CHANGED. |
| 09-008-15-2991C | 2017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN ONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. “IPOD ERROR” MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. |
| 01-007-15-3025 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE A CHECK ENGINE LIGHT ON WITH DTCS P0011:00 AND/OR DTC P0012:00 STORED IN MEMORY. • P0011:00: ELECTRIC VARIABLE VALVE TIMING CONTROL SYSTEM - OVER-ADVANCED) • P0012:00: ELECTRIC VARIABLE VALVE TIMING CONTROL SYSTEM - (OVER-RETARDED) THIS CONCERN MAY BE CAUSED BY VARIABLE VALVE TIMING (VVT) ACTUATOR SPRING SHAFT FATIGUE. DURING VEHICLE USAGE, THE SPRING SHAFT MAY FAIL AND CAUSE INCORRECT VVT OPERATION AND CHECK ENGINE LIGHT ILLUMINATION. THE INSPECTION PROCEDURE HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN IN THE FUTURE. |
| 02-002-15-3002B | 2017-06-07. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. AFTER PERFORMING RECALL CAMPAIGN 8014J, OR THE VEHICLE VIN IS NOT APPLICABLE TO 8014J, SOME VEHICLES MAY EXPE-RIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. THIS MAY BE CAUSED BY IMPROPER TIRE AIR PRESSURE DETECTION BY THE TPMS SYSTEM ON CERTAIN TYPES OF ROAD SURFACES. |
| 01-008-15-3045 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. • P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON. |
| 09-016-15-3041 | 2017-06-07. Service bulletin. STRUCTURE:BODY:DOOR. SOME VEHICLES MAY EXPERIENCE A RATTLE NOISE FROM THE FRONT DOOR GLASS WHEN DRIVING WITH THE WINDOW OPEN APPROX. 1/2 TO 4 INCHES (1 - 10 CM). THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. TO INCREASE THE HOLDING FORCE, THE SHAPE OF GLASS RUN CHANNEL HAS BEEN CHANGED AND NON-WOVEN PADS HAVE BEEN ATTACHED TO THE GLASS RUN CHANNEL. |
| 02-005-15-3044 | 2017-06-07. Service bulletin. SUSPENSION:REAR:SHOCK ABSORBER. SOME VEHICLES MAY EXHIBIT A CHIRP/CLUNK TYPE NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE. |
| 05-002-15-3019D | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. |
| 09-021-15-3038 | 2017-06-07. Service bulletin. STRUCTURE:BODY:TRUNK LID. SOME VEHICLES MAY EXHIBIT A CONDITION THAT WATER ENTERS INTO THE TRUNK LID LIGHT WHILE WASHING THE VEHICLE WITH HIGH PRESSURE. WATER MAY ENTER THROUGH THE TRUNK LID LIGHT GASKET AND THE BODY PANEL. |
| 01-015-15-3064A | 2017-05-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 °F (0 °C). • P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM • P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED. |
| 01-023-15-3084 | 2017-05-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 03-006-15-3086 | 2017-05-31. Service bulletin. WHEELS:HUB. SOME VEHICLES MAY EXHIBIT A GROAN TYPE NOISE FROM THE FRONT WHEEL HUB BEARING WHILE DRIVING AT HIGH SPEED OR WHEN CORNERING. THIS MAY BE CAUSED BY FRONT WHEEL HUB BEARING CORROSION. |
| 02-005-16-3152A | 2017-05-30. Service bulletin. SUSPENSION:FRONT:STABILIZER BAR. BEGINNING WITH THE CX-5 AND MAZDA6 MODELS, GRIP TYPE FRONT AND REAR STABILIZER BUSHINGS HAVE BEEN INCORPO-RATED FOR NOISE PREVENTION PURPOSES. IF ANY TYPE OF GREASE OR LUBRICATION IS APPLIED TO THE BUSHINGS, IT MAY CREATE NOISE DUE TO BUSHING SLIPPAGE. |
| 02-010-16-3170 | 2017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE:FRAME AND MEMBERS; SUSPENSION:FRONT:SHOCK ABSORBER. SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:•UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)•STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)•THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)•THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT. |
| 01-009-16-3172 | 2017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 09-016-16-3158 | 2017-05-30. Service bulletin. SEATS. AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE. |
| 02-009-16-3155 | 2017-05-30. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR. SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. |
| 05-002-16-3129 | 2017-05-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. THE NEW SKYACTIV-DRIVE FW6A-EL AT USES “AUTOMATIC TRANSMISSION FLUID (ATF) TYPE: FZ”. ONLY USE “ATF-FZ” TO FILL OR TOP OFF THE FLUID LEVEL. ATF-FZ IS SPECIALLY DESIGNED FOR USE IN THE SKYACTIV-DRIVE SERIES AT. IT IS A LOW VISCOSITY FORMULA WITH LESS FRICTION FOR BETTER FUEL ECONOMY. NOTE: ATF-FZ IS COLORED BLUE FOR EASY IDENTIFICATION. TO CHECK THE FLUID LEVEL, REMOVE THE BOLT, THEN REMOVE THE DIPSTICK. THE DIPSTICK IS MARKED WITH A “FZ” ON SKYACTIV-DRIVE FW6A-EL AT. WHEN FINISHED, INSERT THE DIPSTICK AND INSTALL THE BOLT. |
| 09-003-16-3130 | 2017-05-26. Service bulletin. EXTERIOR LIGHTING:TAIL LIGHTS; EXTERIOR LIGHTING:HEADLIGHTS. SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT (HEADLAMP/HEADLIGHT) OR REAR (TAILLAMP/TAIL-LIGHT) COMBINATION LIGHTS. THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMP-TOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM. |
| 05-001-15-2920 | 2017-05-25. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY. SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: • HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR. • SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.