WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Mazda Mazda6

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

609 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
01-001-14-2868A2017-04-27. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY EXPERIENCE ONE OF THE FOLLOWING TWO SYMPTOMS: 1. SYMPTOM (MAZDA6 ONLY) A. WARNING MESSAGE “I-ELOOP INSPECTION REQUIRED” IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY WHILE DRIVING. B. THE MASTER WARNING LIGHT WILL BE ILLUMINATED. C. DTC P1794:00 (CAPACITOR (I-ELOOP) SYSTEM: CAPACITOR (I-ELOOP) MALFUNCTION) WILL BE STORED IN PCM MEMORY.2. SYMPTOM (MAZDA3 AND MAZDA6) A. WARNING MESSAGE “BATTERY MANAGEMENT SYSTEM INSPECTION REQUIRED” AND THEN "CHARGING SYSTEM MALFUNCTION/ENGINE COULD STOP UNEXPECTEDLY” IS DISPLAYED IN THE INSTRUMENT CLUSTER INFORMATION DISPLAY AFTER DRIVING IN THE RAIN. B. THE MASTER WARNING LIGHT WILL BE ILLUMINATED. THE MAZDA6 WARNING INDICATOR LIGHT AND WARNING MESSAGES ARE SHOWN BELOW: C. THE FOLLOWING DTCS ARE STORED IN PCM MEMORY: • DTC P1794:00 - CAPACITOR (I-ELOOP) SYSTEM: CAPACITOR (I-ELOOP) MALFUNCTION • DTC P2502:00 - GENERATOR SYSTEM: MALFUNCTION IN VOLTAGE GENERATED BY GENERATOR
09-007-14-28782017-04-26. Service bulletin. EXTERIOR LIGHTING:FOG LIGHTS. SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT OR REAR COMBINATION LIGHTS. THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMPTOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.
09-010-14-28732017-04-26. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). AN UPDATED VERSION OF THE SOFTWARE FOR THE TOMTOM NAVIGATION SYSTEM HAS BECOME AVAILABLE. UNDER THIS MSP42, THE NAVIGATION SYSTEM WILL BE REFLASHED TO THE UPDATED VERSION USING A SD CARD. THIS SOFTWARE UPDATE WILL ELIMINATE CANCELING VOICE RECOGNITION WHEN VEHICLE SPEED TRANSITIONS PAST 4MPH AND IMPROVE THE FOLLOWING: • SYSTEM STABILITY • SPEECH RECOGNITION • VERBAL AND VISUAL INSTRUCTIONS FOR ROUTE GUIDANCE (3D VIEW NOW INCLUDES MORE VISUAL FEEDBACK SUCH AS ARROWS INDICATING WHICH LANE TO USE IN COMPLICATED INTERCHANGES) • COMMANDER SWITCH CONTROL (FOR VEHICLES EQUIPPED) • GPS RECOVERY AFTER SIGNAL IS LOST (TUNNELS, PARKING GARAGES, ETC.) CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
09-010-14-2873A2017-04-26. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). AN UPDATED VERSION OF THE SOFTWARE FOR THE TOMTOM NAVIGATION SYSTEM HAS BECOME AVAILABLE. UNDER THIS MSP42, THE NAVIGATION SYSTEM WILL BE REFLASHED TO THE UPDATED VERSION USING A SD CARD. THIS SOFTWARE UPDATE WILL ELIMINATE CANCELING VOICE RECOGNITION WHEN VEHICLE SPEED TRANSITIONS PAST 4MPH AND IMPROVE THE FOLLOWING: • SYSTEM STABILITY • SPEECH RECOGNITION • VERBAL AND VISUAL INSTRUCTIONS FOR ROUTE GUIDANCE (3D VIEW NOW INCLUDES MORE VISUAL FEEDBACK SUCH AS ARROWS INDICATING WHICH LANE TO USE IN COMPLICATED INTERCHANGES) • COMMANDER SWITCH CONTROL (FOR VEHICLES EQUIPPED) • GPS RECOVERY AFTER SIGNAL IS LOST (TUNNELS, PARKING GARAGES, ETC.) CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
SA2882017-03-01. Service bulletin. ELECTRICAL SYSTEM. IF YOU ENCOUNTER A VEHICLE WITH DTC P0137 (CIRCUIT LOW INPUT), CHECK THE REAR HARNESS AT THE RED CIRCLED AREA IN THE FOLLOWING DIAGRAM. IF AN AFTERMARKET ALARM SYSTEM IS INSTALLED, THE REAR HARNESS MIGHT HAVE RECEIVED DAMAGE FROM ELECTRO-TAP CONNECTORS (A) OR TO THE PROTECTOR TUBE (B). THIS DAMAGE IS NOT COVERED UNDER WARRANTY.
09-009-16-3150A2017-03-01. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXHIBIT BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.
09-033-16-32062017-03-01. Service bulletin. STRUCTURE:BODY:TRUNK LID. SOME VEHICLES MAY EXHIBIT A CONDITION THAT WATER ENTERS INTO THE TRUNK LID LIGHT WHILE WASHING THE VEHICLE WITH HIGH PRESSURE. WATER MAY ENTER THROUGH THE TRUNK LID LIGHT GASKET AND THE BODY PANEL.
09-030-16-32042017-03-01. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXHIBIT A TOUCH SCREEN THAT LOCKS UP (BLACK SCREEN) OR DOES NOT RESPOND. HOWEVER, IN EITHER CASE THE AUDIO SOUND IS NORMAL. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE AUDIO UNIT. THE PRODUCTION PROCESS AT THE AUDIO SUP-PLIER HAS BEEN IMPROVED TO ELIMINATE THESE CONCERNS.
01-009-16-3172A2017-02-28. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
01-011-16-31392017-02-28. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
01-010-16-31852017-02-28. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0421:00 (CATALYTIC CONVERTER SYSTEM) WITH-OUT EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY).THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM THAT MAY DETECT FALSE ERROR OF THE A/F SENSOR, RESULTING IN FALSE DETECTION OF P0421. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED.CATALYST MON-ITOR FUNCTION EXPLANATION•THE PCM MONITORS THE OXYGEN STORAGE AMOUNT PROPORTIONAL TO CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC.•THE PCM STARTS TO MONITOR AFTER RECOVERY (FUEL INJECTION STARTS) FROM FUEL CUT CONTROL.•THE PCM TEMPORARILY CHANGES THE TARGET AIR/FUEL RATIO TO RICH AT FUEL CUT RECOVERY, AND DETECTS THE RESPONSE TIME UNTIL THE HO2S OUTPUT SIGNAL OUTPUTS THE VOLTAGE ON THE RICH SIDE. IF THE CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC DETERIORATES, THE AMOUNT OF THE TIME UNTIL THE HO2S DETECTS THE VOLTAGE ON THE RICH SIDE IS SHORTER COMPARED TO THE NORMAL PURIFICATION CHARACTERISTIC AS SHOWN. THE PCM DETECTS A CATALYTIC CONVERTER MALFUNCTION USING THIS CHARACTERISTIC.
02-010-16-31702017-02-27. Service bulletin. SUSPENSION. SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:•UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)•STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)•THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)•THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6).TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.
09-040-16-32142017-02-24. Service bulletin. VISIBILITY:SUN/MOON ROOF ASSEMBLY. SOME CUSTOMERS MAY COMPLAIN THAT IN EXTREME COLD WEATHER CONDITIONS, THE SUNROOF MAY SUDDENLY OPEN BY ITSELF WHEN THE HEATER IS ON. THIS CONCERN MAY BE DUE TO A SHORT IN THE SUNROOF SWITCH (A) CAUSED FROM CONDEN-SATION GENERATED BETWEEN THE ROOF PANEL AND THE SEAL. TO ELIMINATE THIS CONCERN IN THE FUTURE, A PROTECTIVE FILM HAS BEEN INSTALLED TO THE SWITCH AND A PAD INSTALLED TO THE HARNESS.
09-016-16-3158A2017-02-24. Service bulletin. SEATS. AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.THIS SERVICE BULLETIN IS ONLY FOR SUBLET REPAIR. A QUALIFIED UPHOLSTERY REPAIR SPECIALIST IS REQUIRED FOR THIS REPAIR PROCEDURE. PLEASE PRINT A COPY OF THIS BULLETIN FOR THE UPHOLSTERY REPAIR SPECIALIST.
01-011-16-3139A2017-02-24. Service bulletin. ENGINE. WHEN THE ENGINE IS STARTED FOR THE FIRST TIME AFTER PARKING THE VEHICLE OVERNIGHT IN COLD CONDITIONS (BELOW 32 DEGREES FAHRENHEIT / 0 DEGREES CELSIUS), SOME VEHICLES MAY EXHIBIT A ROUGH IDLE AND/OR THE CHECK ENGINE LIGHT ON WITH ANY OF THE FOLLOWING DTC(S) STORED IN MEMORY.•P0300 - RANDOM MISFIRE DETECTED•P0301 - CYLINDER NO.1 MISFIRE DETECTED•P0302 - CYLINDER NO.2 MISFIRE DETECTED •P0303 - CYLINDER NO.3 MISFIRE DETECTED •P0304 - CYLINDER NO.4 MISFIRE DETECTED THIS MAY BE CAUSED BY FROZEN WATER ACCUMULATED IN THE MAIN SILENCER, RESTRICTING EXHAUST FLOW.
01-009-16-3172B2017-02-24. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
01-014-16-32082017-02-24. Service bulletin. ELECTRICAL SYSTEM:IGNITION. SOME VEHICLES MAY EXPERIENCE A LACK OF ENGINE POWER/ROUGH IDLING AND THE CHECK ENGINE LIGHT ON WITH ONE OR MORE OF THE MISFIRE RELATED DTCS OF P0300:00, P0301:00, P0302:00, P0303:00 AND P0304:00. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE IGNITION COIL(S) DUE TO A HIGH DIFFERENCE BETWEEN COLD AND WARM AMBIENT TEMPERATURES. THE PRODUCTION METHOD OF THE IGNITION COIL HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
09-038-16-32132017-02-23. Service bulletin. STRUCTURE. SOME VEHICLES MAY EXPERIENCE A RATTLE NOISE FROM THE FRONT DOOR GLASS WHEN DRIVING WITH THE WINDOW OPEN APPROX. 1/2 TO 4 INCHES (1 - 10 CM). THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. TO INCREASE THE HOLDING FORCE, THE SHAPE OF GLASS RUN CHANNEL HAS BEEN CHANGED AND NON-WOVEN PADS HAVE BEEN ATTACHED TO THE GLASS RUN CHANNEL.
1080M2017-02-23. Service bulletin. ENGINE. IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT.
1079M2017-02-23. Service bulletin. SERVICE BRAKES. IN CERTAIN CONDITIONS, SMART CITY BRAKE SUPPORT (SCBS) MAY OPERATE UNINTENTIONALLY. THE OWNER'S MANUAL PROVIDES 7 EXAMPLES: OBJECTS ON THE ROAD AT THE ENTRANCE TO A CURVE.VEHICLES PASSING IN THE OPPOSITE LANE WHILE MAKING A CURVE.METAL OBJECTS, BUMPS, OR PROTRUDING OBJECTS ON THE ROAD.WHEN PASSING THROUGH A TOLL GATE.WHEN PASSING UNDER A VINYL CURTAIN OR FLAG.PLASTIC OBJECTS SUCH AS PYLONS.TWO-WHEELED VEHICLES, PEDESTRIANS, ANIMALS OR STANDING TREES.THIS M-TIP ARTICLE PROVIDES 2 ADDITIONAL EXAMPLES:A. THERE IS FOGGING ON THE INNER SURFACE OF THE WINDSHIELD.B. THERE IS/ARE FOGGING/WATER DROPS ON THE OUTER SURFACE OF THE WINDSHIELD.THE NEAR INFRARED LASER BEAM IS A LIGHT BEAM AND IS REFRACTED BY WATER DROPS OR FOREIGN MATERIAL ON THE WINDSHIELD. IN THIS CASE, THE NEAR INFRARED LASER BEAM MAY NOT DETECT AN OBSTRUCTION AHEAD CORRECTLY.
01-016-16-32202017-02-23. Service bulletin. ENGINE. THERE IS A CONCERN THAT SOME WATER PUMPS ARE BEING REPLACED THAT ARE NOT FAULTY, DUE TO SIGNS OF A VERY SMALL COOLANT LEAK FROM THE BLEED HOLE. THIS SERVICE BULLETIN IS TO INFORM YOU ABOUT THE WATER PUMP SEALING MECHA-NISM AND THE CRITERIA IF REPLACEMENT IS NECESSARY OR NOT.
01-017-16-32422017-02-23. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE AN ENGINE THAT RUNS ROUGH AND THE CHECK ENGINE LIGHT ON WITH DTCS P0201 AND P0204 OR P0202 AND P0203.NOTE:ENGINE MISFIRE RELATED DTCS (P0301, P0302, P0303, P0304) ARE USUALLY STORED AT THE SAME TIME.P0201:00: FUEL INJECTOR CIRCUIT/OPEN CYLINDER NO.1P0202:00: FUEL INJECTOR CIRCUIT/OPEN CYLINDER NO.2P0203:00: FUEL INJECTOR CIRCUIT/OPEN CYLINDER NO.3P0204:00: FUEL INJECTOR CIRCUIT/OPEN CYLINDER NO.4THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE PCM (DENSO PRODUCED ONLY). TO CORRECT THE CONCERN, THE PCM INTERNAL FAILURE HAS BEEN ELIMINATED.
00-004-16-32372017-02-22. Service bulletin. EQUIPMENT. RAISING A VEHICLE WITH A JACK CAN BE DANGEROUS IF NOT DONE PROPERLY. THE VEHICLE CAN SLIP OFF THE JACK AND SERI-OUSLY INJURE SOMEONE. IN THIS SERVICE INFORMATION, SOME IMPORTANT WARNINGS AND CAUTIONS HAVE BEEN TAKEN FROM THE OWNER’S MANUAL. FOR MAZDA CUSTOMERS WHO HAVE QUESTIONS ABOUT SAFELY LIFTING THEIR VEHICLE TO CHANGE A FLAT TIRE OR TO INSTALL SNOW CHAINS, PLEASE PROVIDE A COPY OF THE ATTACHED HANDOUT FOR THEM. ALSO, BE SURE TO ALWAYS DIRECT CUSTOMERS TO FOL-LOW THE DIRECTIONS IN THE OWNER'S MANUAL.
1099M2017-02-22. Service bulletin. ELECTRICAL SYSTEM. WHEN REPROGRAMMING A CONTROL MODULE, ALWAYS USE THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE. IF NOT USED, THE CONTROL MODULE REPROGRAMMING MAY FAIL DUE TO A WEAK VEHICLE BATTERY.THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE PREVENTS THE VEHICLE BATTERY FROM BEING DISCHARGED. THIS ALLOWS THE IDS TO REPROGRAM A CONTROL MODULE WITHOUT INTERFERENCE FROM A WEAK OR UNDERCHARGED VEHICLE BATTERY. NOTE: CONTROL MODULE DAMAGE MAY OCCUR IF THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE IS NOT USED.
1066M2017-02-22. Service bulletin. EXTERIOR LIGHTING. SOME CUSTOMERS MAY COMPLAIN ABOUT IMPROPER OPERATION OF THE AUTO-DIMMING MIRROR. THIS MAY BE CAUSED BY AN OBSTRUCTION OF THE FRONT AND/OR REAR LIGHT SENSOR(S) (E.G. HANGING A PARKING PERMIT FROM THE MIRROR). USE A SOFT CLOTH WITH MILD DETERGENT TO CLEAN THE MIRROR. HARSH DETERGENT MAY DAMAGE THE FRONT AND/OR REAR LIGHT SENSOR(S).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.