WenmarOpen by Wenmar Pro

Service bulletins for the 2026 Mazda CX-50

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

91 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
8026C CV Notification2026-07-03. Emissions. UNKNOWN OR OTHER. 2026 CX-50 Hybrid Battery Label Concern - Emissions Recall 8026C Mazda Motor Corporation has decided to conduct a Voluntary Emissions Recall Campaign on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this Emissions Recall. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the hybrid battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s traction battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
8026C Repair a2026-07-03. Emissions. UNKNOWN OR OTHER. 2026 CX-50 Hybrid Battery Label Concern - Emissions Recall 8026C Mazda Motor Corporation has decided to conduct a Voluntary Emissions Recall Campaign on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this Emissions Recall. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the hybrid battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s traction battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SA-042-262026-07-03. Service bulletin. ENGINE; ELECTRICAL SYSTEM; UNKNOWN OR OTHER. This Service Alert supersedes the previously issued SAs listed below. The changes are noted in Red text. SA-017/25 12/16/25, 09/08/25, 07/14/25, 05/15/25 and 03/21/25 DESCRIPTION Mazda Connect Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out
SA-041-262026-07-03. Service bulletin. ELECTRICAL SYSTEM; ENGINE. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
SA-040-262026-07-03. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-009/25 08/22/25 and 02/18/25 DESCRIPTION Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs. Index System Outline • MYMAZDA App Connected Vehicle (CV) Error Codes • Vehicle Confirmation Instructions • Troubleshooting Instructions • Resources
SA-039-262026-07-03. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. This Service Alert supersedes the previously issued SA listed below. The changes are noted in Red text. SA-012/25 10/06/25, 08/21/25, 05/15/25 and 02/27/25 DESCRIPTION Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE NOTE: Before proceeding: Document the vehicle's current MAZDA CONNECT CMU software version. • 2019-2022 Models - Go to TSB 16-003/23 and confirm the CMU Serial Number is not within the affected range. • Document customer device Brand/Model/Model Number/software version on the repair order. • Confirm that the Connectivity Master Unit (CMU) is updated to the latest software version. Go to MGSS -> Infotainment -> MAZDA CONNECT Updates ○ • If possible, complete the Microsoft Forms Questionnaire. Go to MGSS -> Infotainment -> MAZDA CONNECT Questionnaire.
SSPE1 Repair a2026-07-03. Service campaign. ELECTRICAL SYSTEM. Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SA-037-26a2026-07-03. Service bulletin. ELECTRICAL SYSTEM. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. SA-037/26 05/28/26 DESCRIPTION Replacement battery packs for High Voltage systems are supplied with an additional label that matches the one attached to the service battery pack (refer to the sample High Voltage Battery Label image for reference). When replacing the battery pack in a 2026 or later model that has a similar label at the base of the left B-pillar, replace the label with the new one included in the service parts battery pack. REPAIR PROCEDURE Label Application: When replacing a High Voltage Battery: refer to the Label Application Process included in the "HIGH VOLTAGE BATTERY REMOVAL/INSTALLATION" or "M Hybrid Boost BATTERY REMOVAL/INSTALLATION" procedures in the Workshop Manual for the applicable models.
SA-027-26a2026-07-03. Service bulletin. ELECTRICAL SYSTEM. This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-027/26 04/16/26 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. REPAIR PROCEDURE 1. Perform appropriate repair to vehicle. If needed, use the Battery Diagnostics of the DCA-8000 to test the charging and starting systems by following the on-screen instructions for entering the appropriate information. Refer to the Mazda DCA-8000 Instruction Manual for more information.
16-010-262026-07-02. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. COMPLIANCE WITH NEW YORK STATE GENERAL BUSINESS LAW §399‑CCCCC (CONNECTED VEHICLE SERVICE; DOMESTIC VIOLENCE VICTIMS) DESCRIPTION This Service Information is issued in accordance with New York State General Business Law §399􀀀CCCCC (Connected Vehicle Service; Domestic Violence Victims). This regulation is intended to protect victims of domestic violence by allowing them to request the termination of third-party access (including access by an alleged abuser) to connected vehicle services, such as vehicle location tracking and remote control functions. To support this requirement, this Service Information enables confirmation of whether a vehicle is subject to connected vehicle services by referring to the SUBJECT VIN & PRODUCTION DATE RANGE, and provides guidance on the procedure to terminate such services when a customer requests the removal of third-party access for an applicable vehicle. Effective July 1, 2026, if a customer requests action under this regulation, a CMU/CDC software update must be performed to enable appropriate control of connected vehicle service access. If no request is made by the customer, the CMU/CDC software update is not required. REPAIR PROCEDURE 1. Confirm that the customer has requested deactivation of connected services in accordance with New York State General Business Law related action. 2. Perform the CMU/CDC software update according to the procedures outlined in the appropriate TSB shown in the table below:
16-002-26a2026-07-02. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. UPDATED SOFTWARE RELEASE FOR CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 16-002/26 01/12/26 DESCRIPTION The release notes outlined below provide an overview of bug fixes, feature improvements, and updates included in the latest software release. The latest version of software contains all the updates of the previous versions. NOTE: If current version is not 7230C1A-NA02_***** , this TSB is not applicable. Version 7230C1A-NA02_10022 enables termination of connected services at customer request and fixes these software errors (bugs): Termination of Connected Services by customers at their initiative has been enabled. Accordingly, the following items have been updated. Add a "Data Communication Information" item under Settings > System Settings>Online Connectivity. ○ Updated the text displayed on the confirmation screen for disabling Connected Services. ○ • The list on the center display may appear distorted, giving a double image. • The system may reboot when the ignition is turned on. However, the camera images on the center display are not affected, and the back camera is usable. • The voice recognition function does not start. • Apple CarPlay® may fail to connect while driving on the highway. REPAIR PROCEDURE 1. Verify the customer concern. 2. Update MAZDA CONNECT with software version 7230C1A-NA02_10022 or later with a USB memory stick using the 7TH GEN MAZDA CONNECT Update Instructions.
16-001-26a2026-07-02. Service bulletin. ELECTRICAL SYSTEM; UNKNOWN OR OTHER. UPDATED SOFTWARE RELEASE FOR CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 16-001/26 01/08/26 DESCRIPTION The release notes outlined below provide an overview of bug fixes, feature improvements, and updates included in the latest software release. The latest version of software contains all the updates of the previous versions. NOTE: If current version is not 7230C1A-NA01_***** or 7230C2A-NA01_*****, this TSB is not applicable. Version 7230C1A-NA01_10022 enables termination of connected services at customer request: Termination of Connected Services by customers at their initiative has been enabled. Accordingly, the following items have been updated. Add a "Data Communication Information" item under Settings > System Settings>Online Connectivity. ○ Updated the text displayed on the confirmation screen for disabling Connected Services. ○ • The list on the center display may appear distorted, giving a double image. • The system may reboot when the ignition is turned on. However, the camera images on the center display are not affected, and the back camera is usable. • The voice recognition function does not start. • Apple CarPlay® may fail to connect while driving on the highway. REPAIR PROCEDURE 1. Verify the customer concern. 2. Update MAZDA CONNECT with software version 7230C1A-NA01_10022/7230C2A-NA01_10014 or later with a USB memory stick using the 7TH GEN MAZDA CONNECT Update Instructions.
SA-034-262026-06-04. Service bulletin. ELECTRICAL SYSTEM; UNKNOWN OR OTHER. This service alert supersedes the previously issued service alert listed below. The changes are noted in Red text. SA-047/25 10/07/25 DESCRIPTION When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated. CAUTION: DO NOT swap TCU with another vehicle as the TCU is VIN locked after activation. A TCU swap with another vehicle will disable Connected Services on both vehicles. • If TCU activation is not performed, connected vehicle functions will not operate. This will have a negative impact on the customer because they will need to return to the dealer for repairs. • If the Telematics Control Unit (TCU) replacement is necessary, check "Vehicle Communication Line Status Reference" status detail first. The TCU can only be replaced under the following "Status Detail" conditions: Open Completed (OK) ○ Closed Completed (OK) ○ ○ If the TCU is replaced under the following "Status Detail" conditions, the customer may not be able to enroll into the replacement TCU. Processing (NG) ○ Request Failed (NG) ○ Open Failed (NG) ○ Flag Setting Failed TCU Activation 1. Install the new TCU.
SA-033-262026-06-04. Service bulletin. ELECTRICAL SYSTEM. This SA supersedes the previously issued SA(s) listed below. The changes are noted below in Red. SA-029/25 10/16/25 and 06/02/25 DESCRIPTION This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure. REPAIR PROCEDURE HIGH VOLTAGE BATTERY MAINTENANCE Verify the State-of-charge (SOC) in the instrument cluster. MX-30 EV: If the SOC is lower than 26%, charge it to 50% (either by normal charging or quick charging). CX-90/CX-70 PHEV: If the SOC is lower than 1%, charge it to 10% (either by normal charging, quick charging or engine running).
SA-032-262026-06-04. Service bulletin. FUEL/PROPULSION SYSTEM. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-011/25 10/16/25 and 02/27/25 DESCRIPTION Some customers will report that their fuel door (AKA, fuel filler door, fuel lid, and fuel-filler lid) was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-007/25 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2025 Mazda3 and 2020-2025 CX-30 are present. REPAIR PROCEDURE 1. Check for pry marks around the door opening. Are there any pry marks? YES: This is due to outside influence and is not covered by Mazda warranty. NO: Continue to the next step. 2. Check the fuel door lock operation. a. Lock the doors and verify if the fuel door lock is locking. NOTE: The default setting is a 90-second delay after the doors lock, but the customer can set that to 0, 30, 60, 90, or 120 seconds. b. Unlock the doors and verify if the fuel door lock is unlocking. NOTE: There is no delay to this function, but the fuel door must be locked to confirm it is unlocking. See the lock note above. Is the fuel door lock operation working correctly? YES: The fuel door repair IS NOT covered by Mazda warranty. The fuel door lock is OK and the door was damaged because the vehicle was not unlocked. NO: The fuel door repair IS covered by Mazda warranty. The fuel door lock is NOT OK and damage to the door was done in order to access the lock. NOTE: If the door was already broken when it arrived at the dealership, Mazda will pay for the fuel door repair under warranty if the vehicle does NOT have an emergency release. Mazda will NOT pay for the fuel door under warranty if it has an emergency release.
SA-037-262026-06-04. Service bulletin. ELECTRICAL SYSTEM; UNKNOWN OR OTHER. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. SA-049/25 10/16/2025 DESCRIPTION Replacement battery packs for High Voltage systems are supplied with an additional label that matches the one attached to the service battery pack (refer to the sample High Voltage Battery Label image for reference). When replacing the battery pack in a 2026 or later model that has a similar label at the base of the left B-pillar, replace the label with the new one included in the service parts battery pack. REPAIR PROCEDURE Label Application: When replacing a High Voltage Battery: refer to the Label Application Process included in the "HIGH VOLTAGE BATTERY REMOVAL/INSTALLATION" or "M Hybrid Boost BATTERY REMOVAL/INSTALLATION" procedures in the Workshop Manual for the applicable models. In addition to the procedures outlined in the Workshop Manual, please follow these additional steps when removing an existing label to help simplify the application of the new one:
SSPE1 Warr2026-06-03. Emissions. UNKNOWN OR OTHER. Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SSPE1 Repair2026-06-03. Emissions. UNKNOWN OR OTHER. Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SSPE1 Owner Ltr2026-06-03. Emissions. UNKNOWN OR OTHER. Special Service Program (SSPE1) - 2026 CX-50 Hybrid – Battery Label Concern Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2026MY CX-50 vehicles produced from September 8, 2025 through September 26, 2025. If you receive this notice, your vehicle is included in this SSP. What is the problem? On certain CX-50 Hybrid vehicles, inappropriate battery labels were attached to the center pillar and the traction battery beneath the rear seat. QR codes printed on these labels are incorrect and do not link to the battery information website, the required information related to the vehicle’s hybrid battery cannot be displayed. This condition does not comply with Section 1962.6 (Battery Labeling Requirements), Title 13 of the California Code of Regulations. Although only the six states (California, Massachusetts, New York, Oregon, Vermont and Washington) have adopted the battery labeling requirements of Section 1962.6 starting with the 2026MY, Mazda is also implementing corrective action for vehicles in all other states. What will Mazda do? Your Mazda dealer will attach the correct battery labels to the center B-pillar and the hybrid battery, free of charge.
SA-031-262026-05-05. Service bulletin. STRUCTURE:BODY; UNKNOWN OR OTHER. DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the B􀀀pillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.
SA-029-262026-05-05. Service bulletin. UNKNOWN OR OTHER; ENGINE; POWER TRAIN; SERVICE BRAKES. This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).
SA-027-262026-05-05. Service bulletin. ELECTRICAL SYSTEM. This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-007/25 10/22/25, 06/02/25 and 02/03/25 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries. TEST PROCEDURE 1. Connect the charger clamps to the appropriate battery posts.
SA-026-262026-05-05. Service bulletin. ENGINE. This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.
SA-021-262026-05-05. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY. This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure.
SA-028-262026-05-04. Service bulletin. STEERING; SUSPENSION. DESCRIPTION Some vehicles may exhibit a clicking, popping, tapping or knocking noise from the front when turning left or right and accelerating. NOTE: The noise could occur at different steering wheel angles or power levels. Due to the insulating properties of the suspension and chassis, it can be difficult to determine which driveshaft is at fault by listening from inside the vehicle. See the attached video for an example of an outer CV joint clicking. Repair Procedure: Replace the affected driveshaft after confirming the source of the noise using chassis ears. Both driveshafts may be faulty; verify each side before replacement.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.