WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Mazda CX-5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

824 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Equipment and accessories are shown. Show all

Bulletins, newest first
02-010-16-31702017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE:FRAME AND MEMBERS; SUSPENSION:FRONT:SHOCK ABSORBER. SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:•UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)•STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)•THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)•THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT.
01-009-16-31722017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME.
07-001-15-29932017-05-25. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. SOME VEHICLES (ONLY EQUIPPED WITH MANUAL A/C OR WITHOUT A/C) MAY EXHIBIT A BLOWER MOTOR THAT ONLY OPERATES IN THE HIGHEST SPEED (4TH) AND DOES NOT OPERATE AT SPEEDS 1 - 3. THIS CONCERN OCCURS MOSTLY IN COLDER REGIONS AND MAY BE CAUSED BY A BLOWN RESISTOR FUSE. TO ELIMINATE THIS CONCERN, A SPECIAL SERVICE PART BLOWER MOTOR HAS BEEN ESTABLISHED.
07-002-15-30042017-05-25. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CONCERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. SOME DEFORMED EVAPORATOR TUBES SLIPPED THROUGH QUALITY INSPECTION AND WERE USED DURING PRODUCTION. A/C REFRIGERANT LEAKS FROM IMPROPER BRAZING AT A JOINT. TO CORRECT THE PROBLEM, THE PRODUCTION AND INSPECTION CONTROL OF THE EVAPORATOR HAVE BEEN IMPROVED.
02-003-15-29902017-05-25. Service bulletin. EQUIPMENT:MECHANICAL. SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT STRUT BEARING (A) WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO UPPER FRONT STRUT BEARING DAMAGE OR IT MAY BE DUE TO STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE: 1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING HAS BEEN CHANGED. 2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. NOTE: THE PISTON ROD NUT (B) REQUIRES REPLACEMENT WHEN THE FRONT STRUT BEARING IS REPLACED.
01-003-15-30142017-05-25. Service bulletin. EQUIPMENT. USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.
05-004-15-30342017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. • DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
05-005-15-30272017-05-19. Service bulletin. EQUIPMENT. SOME CUSTOMERS MAY COMPLAIN OF A WHINING NOISE FROM THE AUTOMATIC TRANSAXLE WHEN DRIVING AT 10 MPH AND ABOVE. THE NOISE: • DEPENDS ON THE VEHICLE’S SPEED ONLY (THE MORE SPEED, THE MORE NOISE) • OCCURS WITH ALL TYPES OF DRIVING (ACCELERATION, DECELERATION, STEADY SPEED) • DOES NOT DEPEND ON RPM, GEAR, OR ATF TEMPERATURE THIS IS CAUSED BY A DAMAGED BEARING IN THE TRANSAXLE DUE TO IMPROPER CONFIGURATION OF THE TRANSAXLE CASE. A MODIFICATION HAS NOW BEEN IMPLEMENTED ON AUTOMATIC TRANSAXLES WITH THE SERIAL NUMBER 3TR1111680 AND HIGHER OR 3TD1104906 AND HIGHER. THE SERIAL NUMBER CAN BE FOUND ON TOP OF THE TRANSAXLE CASE NEAR THE MANUAL SHAFT LEVER.
01-004-15-30282017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0191:00 OR DTC P0088:00 STORED IN MEMORY. DTC P0191:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (EXCEPT 2014 MAZDA3) DTC P0088:00: FUEL PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE PROBLEM (2014 MAZDA3) THIS IS CAUSED BY THE HIGH PRESSURE FUEL PUMP NOT GENERATING THE TARGET FUEL PRESSURE (DUE TO A MANUFACTURING ERROR OF THE INNER PARTS). TO CORRECT THE PROBLEM, PRODUCTION CONTROL HAS BEEN IMPROVED.
01-005-15-30302017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.
05-004-15-3034A2017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. • DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
05-002-15-3019C2017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
05-004-15-3034B2017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN OF A CHECK ENGINE LIGHT AND A/T WARNING LIGHT ON WHEN STARTING THE ENGINE. AT THE SAME TIME, AN ENGINE INSPECTION REQUIRED MESSAGE IS DISPLAYED ON THE LCD. DTC P0722:00 IS STORED IN THE TRANSMISSION CONTROL MODULE (TCM) MEMORY. • DTC P0722:00 (OPEN CIRCUIT IN OUTPUT SPEED SHAFT CIRCUIT) THE TCM CONTROL LOGIC HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
02-005-14-29812017-05-19. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET.
00-004-14-29832017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. IN SUPPORT OF THE SKYACTIV MODELS, MAZDA WILL MAKE AVAILABLE A SPECIAL SERVICE TOOL (SST), TO ADDRESS FRONT SUSPENSION NOISE FOR SPECIFIC HIGH HUMIDITY AND WET CLIMATE CONDITIONS IN THE LOWER GULF STATES. THE SST WILL BE NEEDED TO COMPLETE REPAIRS DETAILED IN TSB 02-005/14 AND IS AVAILABLE THROUGH MAZDA’S TOOL VENDOR, SNAP-ON TOOLS.
01-019-14-29852017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL.P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTEDTHIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.
05-002-15-30192017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
09-008-15-2991A2017-05-18. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDSFREE MODULE WILL NOT ADDRESS THE “IPOD ERROR” MESSAGE CONCERN FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6 AT THIS TIME.
09-008-15-2991B2017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM:SOFTWARE. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE EFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. “IPOD ERROR” MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
05-002-15-3019A2017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
05-002-15-3019B2017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
SA-041-172017-05-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. PERMANENT DTCS ARE NOW DISPLAYED WITH THE IDS 104 UPDATE. THE PURPOSE OF A PERMANENT DTC IS TO PREVENT CUSTOMERS FROM CLEARING THEM BY DISCONNECTING THE BATTERY CABLE IN ORDER TO PASS A SMOG CHECK. ALL PCM AND TCM DTCS THAT TURN ON THE CHECK ENGINE LIGHT CAN REMAIN AS A PERMANENT DTC. THEY WILL NOT TURN ON THE CHECK ENGINE LIGHT OR CAUSE DRIVABILITY CONCERNS. IF YOU ENCOUNTER A PERMANENT DTC, IGNORE IT AND DIAGNOSE THE CURRENT STORED OR PENDING DTC.
SA-040-172017-05-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE ONE OF THE FOLLOWING ADVANCED KEYLESS ENTRY SYSTEM MALFUNCTIONS: (1) KEY FOB AND/OR DOOR REQUEST SWITCH DOES NOT OPERATE. (2) DOOR LOCKS REPEATEDLY LOCK AND UNLOCK WHEN APPROACHING THE VEHICLE WITH THE ADVANCED KEY. (3) KEY WARNING LIGHT (RED) ON WHILE DRIVING AND DTC B10D1:23 AND/OR B10D3:23 IS(ARE) STORED. •B10D1:23 REQUEST SWITCH (LF) CIRCUIT MALFUNCTION •B10D3:23 REQUEST SWITCH (RF) CIRCUIT MALFUNCTION
01-011-15-3051A2017-05-16. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE A LACK OF POWER DURING HARD ACCELERATION (APPROX. 6,000 RPM) IN COLD WEATHER CONDITIONS BELOW 32 °F (0 °C). DTCS P0300:00, P0301:00 AND/OR P0302:00 ARE STORED IN MEMORY. • P0300:00: RANDOM MISFIRE DETECTED • P0301:00: CYLINDER NO. 1 MISFIRE DETECTED • P0302:00: CYLINDER NO. 2 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. THE PCM MAY DETECT A FALSE MISFIRE UNDER THE SUBJECT CONDITIONS AND MAY FALL INTO FAIL SAFE MODE. TO ELIMINATE THIS CONCERN, THE PCM CONTROL LOGIC HAS BEEN CHANGED.
01-005-15-3030A2017-05-16. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.