WenmarOpen by Wenmar Pro

Service bulletins for the 2020 Lincoln Aviator

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

328 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
SSM 552282026-10-12. Service bulletin. ENGINE; UNKNOWN OR OTHER. Some 2020-2026 Aviator/Explorer/F-150/Bronco/Ranger vehicles equipped with a 2.7L or 3.0L (non-diesel) engine may need the front engine cover removed and reinstalled for various reasons. The Workshop Manual (WSM), Section 303-01 Engine > Removal and Installation > Engine Front Cover service procedure has been updated to include a new essential special service tool (ESST) guide pin alignment tool (303-1790) that is used to align the engine front cover to the engine block, preventing the O-ring seal on the engine oil galley feed tube from getting damaged during installation.
SSM 552172026-10-06. Service bulletin. ENGINE; UNKNOWN OR OTHER. Some 2020-2024 Explorer/Aviator vehicles equipped with 3.0L EcoBoost/hybrid engine may exhibit blue or black exhaust smoke on startup for the first 5 minutes after an overnight cold soak with no illuminated malfunction indicator lamp (MIL) or powertrain diagnostic trouble codes (DTCs) present. This may be due to engine oil breaching the dynamic oil seals separating the bearing core from the turbine housing in the left side turbocharger assembly. There is a new, updated left side turbocharger oil supply tube equipped with an internal check valve to prevent the engine oil from entering turbine housing after the engine is off. Replace the existing left side turbocharger oil supply tube with the updated service part that includes the check valve (service part# L1MZ-9T516-B) or latest level part. Refer to the Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger > Removal and Installation > Turbocharger Oil Supply Tube LH. For claiming, use causal part 9T516 and labor operation code 9440AL.
SSM 542622025-10-07. Service bulletin. ENGINE. Some 2019-2020 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost, 2020 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L plug-in hybrid electric vehicle (PHEV) engine, 2020 Explorer vehicles equipped with a 3.0L EcoBoost, and 2020 F-150 vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine. This noise may occur on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to an internal component of the variable cam timing (VCT) unit. If diagnostics lead to the VCTs as the source of the noise, refer to the 2024 F-150 Workshop Manual (WSM), Section 303-00 > Diagnosis and Testing > Engine > Pinpoint Test F. Pinpoint test F has been updated to include additional steps along with a video on how to identify the single affected VCT unit that requires replacement.
SSM 537642025-05-21. Service bulletin. POWER TRAIN; ENGINE. Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
TSB 23-20582024-04-03. Service bulletin. ENGINE AND ENGINE COOLING. This TSB supersedes TSB 22-2377 to update the vehicle model years affected and Parts List. Some 2020-2023 Explorer vehicles equipped with a 3.0L EcoBoost engine or 2020-2023 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L PHEV engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn VCT unit. To correct the condition, follow the Service Procedure to replace the VCT units
SSM 523352024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 522442024-02-14. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost hybrid engine, 2020-2023 Explorer vehicles equipped with a 3.3L hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM) and auto start/stop disabled. This may be due to a loose wiring connection to the belt integrated starter generator (BISG). The Workshop Manual (WSM) has recently been updated to provide new direction for DTC P0A1E. Refer to the WSM, Section 303-06 Starting System, Diagnosis and Testing, Starting System for applicable diagnosis.
TSB 23-23472023-11-21. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. This article supersedes TSB 23-2279 to update the Service Procedure. Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost hybrid engine, 2020-2023 Explorer vehicles equipped with a 3.3L hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a powertrain malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). This may be due to the belt integrated starter generator (BISG). To correct this condition, follow the Service Procedure to diagnose and repair this symptom.
SSM 518812023-09-03. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. 2020-2023 Explorer non-hybrid vehicles and equipped with a 3.0L EcoBoost or 3.3L Duratec engine and 2020-2023 Aviator non-hybrid vehicles equipped with a 3.0L EcoBoost engine built on or before 01-Jan-2023 may exhibit an exhaust rattle requiring replacement of the left or right exhaust flexible pipe (5G203). The updated part locates the flexible joint portion of the pipe closer toward the catalytic converter than the originally equipped part. This is due to a design change with these replacement components which will not cause any functional issues with the vehicle.
SSM 518242023-08-11. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. 2020-2023 Explorer non-hybrid vehicles equipped with a 3.0L EcoBoost or 3.3L Duratec engine and 2020-2023 Aviator non-hybrid vehicles equipped with a 3.0L EcoBoost engine may exhibit an exhaust rattle requiring replacement of the left or right exhaust flexible pipe (5G203). The updated part locates the flexible joint portion of the pipe closer toward the catalytic converter than the originally equipped part. This is due to a design change with these replacement components which will not cause any functional issues with the vehicle.
SSM 516652023-05-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2021-2023 Ford and Lincoln vehicles equipped with a 2.7L or 3.0L engine may exhibit an upper engine thump/knock noise coming from the left cylinder head. This condition is most noticeable at idle and may lessen at higher engine speed or while driving. This condition does not affect vehicle durability and will not get worse over time. Use a stethoscope or chassis ears and listen just behind the left cylinder head intake VCT solenoid on the cam cover to determine if the thump/knock noise is coming from the cylinder head/camshaft. The left cylinder head and the camshaft roller followers are available as service parts.
TSB 22-23772022-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
SSM 510322022-08-22. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Aviator vehicles may exhibit automatic transmission fluid (ATF) contamination in the engine cooling system due to the transmission cooler. If the cooling system becomes contaminated with ATF, the system must be flushed clear of the contamination after the source of the contamination has been repaired. It is generally not necessary to replace the following components due to ATF contamination in the cooling system: radiator, heater core, de-gas bottle, water pump, auxiliary water pump, coolant control valves, temperature sensors, thermostat, turbocharger, heat exchangers, tubes, gaskets/O-rings/seals (unless removed), or rubber coolant hoses (unless swollen).
SSM 507482022-05-14. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit erratic shifting and/or a transmission fluid venting condition. If during the preliminary inspection the transmission fluid is found to be a foamy pink color this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly. When repairing or replacing the transmission assembly for an internally leaking transmission fluid cooler assembly, use causal part 7869 and applicable labor operations in Section 07 of the Service Labor Time Standards (SLTS) Manual.
SSM 506392022-03-29. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Some 2020-2022 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual, Maintenance, Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
TSB 22-20782022-03-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Some 20202022 Escape/Aviator plug-in hybrid electric vehicle (PHEV) and 20212022 Corsair PHEV vehicles may exhibit a FordPass or LincolnWay App message notification indicating deep sleep mode and connectivity is temporarily unavailable while the vehicle is plugged in during high voltage battery charging. The vehicle may also exhibit an inoperative remote start feature and/or lock and unlock functionality. This may be due to the software in the telematics control unit (TCU). To correct this condition, follow the Service Procedure to reprogram the TCU.
SSM 503062021-12-07. Service bulletin. ENGINE AND ENGINE COOLING. Some 2018-2021 EcoSport, Expedition, Navigator; 2019-2021 Ranger; 2020-2021 Escape, Corsair, Explorer, Transit; 2021 Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.
SSM 499822021-08-02. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit an inoperative cooling fan and/or a vehicle overheat message. This may be due to water intrusion into the cooling fan relay, a loose ground connection, or damaged wiring. Before replacement of the cooling fan assembly, perform Pinpoint Test KN. Also, locate the cooling fan relay and inspect for water intrusion or damage. The correct location of the cooling fan relay is in the front right portion of the engine bay. If the cooling fan relay is not in the correct location, check behind the front right wheel well in between the splash shield. If any water intrusion or damage is found to the relay, G103, or the connector C1048, replace and correctly mount the affected component as necessary.
SSM 499532021-08-02. Service bulletin. UNKNOWN OR OTHER; ENGINE AND ENGINE COOLING. Some 2021 Explorer ST and Aviator vehicles may exhibit a customer concern of undesirable powertrain sounds inside the vehicle and/or less than optimal speaker sound from the vehicle. This may be due to the engine sound enhancement (ESE) on Explorer ST vehicles and the active noise control (ANC) on Aviator vehicles not being activated. To correct the condition, use the Ford Diagnosis and Repair System (FDRS) > select Toolbox > ACM > ACM - Enable Engine Sound Enhancement and Active Noise Control. Click RUN and follow the on-screen instructions carefully. If prompted with a window stating Feature Not Supported, select OK and continue through the installation application. For claiming use causal 18K810 and applicable labor operations found in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 496962021-03-31. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2021 Explorer/Aviator Hybrid vehicles may exhibit a buzzing noise coming from the center console or cowl area with engine speed around 1500 RPM at idle or while driving. This may be due to the transmission park manual release cable vibrating against the transmission. This can be resolved by isolating the transmission park manual release cable with Rotunda PVC foam tape (164-R4901) or equivalent, where it is contacting the transmission. Replacement of the transmission park manual release cable is not necessary.
SSM 494492021-02-04. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2021 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may appear to have low engine oil level if the proper procedures are not followed. Refer to the Owners Guide, Maintenance, Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
SSM 494072021-01-05. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some 2020 Explorer/Aviator vehicles equipped with a 2.3L/3.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or ECT sensor wiring harness. For 2.3L vehicles, replace the ECT sensor and pigtail wiring connector (GU2Z-14S411-KA). For 3.0L vehicles, replace the ECT and knock sensor. To aid with the engineering investigation, do not disconnect the wiring connector from the ECT sensor during disassembly. Leave the connector on the sensor in case parts are called back for analysis.
TSB 20-24052020-12-05. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE. Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 3.0L EcoBoost engine may exhibit a rough idle with the air conditioning (A/C) on. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
SSM 493292020-12-04. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; ENGINE. Some 2020-2021 Aviator and Explorer vehicles may experience an intermittent no crank, inoperative remote start, and/or an illuminated wrench light with diagnostic trouble codes (DTCs) P07E4, B135C and/or U0103. This may be due to a loose ground G210 and/or G214. Check grounds G210 and G214, refer to the Wiring Diagram for location information. If the concern persists, or the grounds are found to be secure, refer to the Workshop Manual and applicable sections of the Powertrain Controls/Emissions Diagnosis (PC/ED) Manual for normal diagnostics.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.