WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Kia Cadenza

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

117 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
TSB-CLI0242017-08-02. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. TSB: TESTING A/C COMPRESSOR FUNCTION USING GDS - This bulletin provides information on a new procedure to test A/C compressor function using the GDS.
TSB-CHA044R12017-08-02. Service bulletin. STEERING; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. TSB: MDPS FLEXIBLE COUPLING REPLACEMENT - This bulletin provides information related to the replacement of the flexible coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped.
PS3202017-08-02. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. PIT STOP: ROUGH IDLE AFTER COLD START ON 3.3L GDI ENGINE - When addressing a customer complaint of rough idle, which occurs only on the first start of the day and lasts for 30-45 seconds, check for the possibility of poor injector performance in a particular cylinder.
PS3152017-08-02. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS. PIT STOP: GDI INJECTOR SPRAY TIP DEPOSITS - A design feature of vehicles equipped with a Gasoline Direct Injection (GDI) system is the placement of each fuel injector directly into the engine cylinder head assembly. Therefore, it is completely normal for the combustion process to create deposits on the injector spray tip surfaces.
TSB-TRA0512017-08-02. Service bulletin. EQUIPMENT:ELECTRICAL. TSB: 6 SPD A/T SOLENOID REPLACEMENT ? DTC P0741 - This bulletin provides information relating to the replacement of the Damper Clutch (D/C) Solenoid on 6-speed automatic transaxles with DTC P0741 (active or history), instead of replacing the transaxle. To reduce vehicle repair time, this procedure can be performed with the transaxle installed in the vehicle.
TSB-CHA0442017-08-02. Service bulletin. STEERING. TSB: MDPS FLEXIBLE COUPLING REPLACEMENT - This bulletin provides information related to the replacement of the flexible coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped. This condition may be caused by premature wear of the flexible coupling in the MDPS.
TT0572017-08-02. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). TECH TIP: Navigation System Displaying the Wrong Location - Customer complains that the location displayed on the map is different than the actual location (i.e. system shows location in a river, lake, etc.). This tech tip gives the procedure to resolve.
PS3072017-08-02. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. PIT STOP: PROGRAMMING A THIRD SMART KEY ON CERTAIN 2014-15MY VEHICLES - In past Smart Key systems, the maximum amount of keys that could be programmed to a vehicle was 2. On certain 2014-15MY Kia vehicles, the amount of keys that can be programmed to a vehicle has increased to 3. For information on the current number of keys ?learned? by the system, access SMK > Current Data in GDS, as shown below. To program any additional keys, follow the applicable service procedure on KGIS.
TSB-SST0332017-08-02. Service bulletin. LATCHES/LOCKS/LINKAGES:HOOD:LATCH; STRUCTURE:BODY:HOOD. TSB: SPECIAL SERVICE TOOL FOR HOOD RELEASE LEVER REMOVAL - This bulletin provides information related to the introduction of a new Special Service Tool (SST) (A) developed to prevent the hood release lever pivot point (B) from being damaged when removing the hood release lever. Follow the instructions included in this bulletin to properly remove the hood release lever using the new SST.
TSBTRA051R12017-02-17. Service bulletin. POWER TRAIN. TSB: 6 SPD A/T SOLENOID REPLACEMENT – MULTIPLE DTCS - THIS BULLETIN PROVIDES INFORMATION RELATING TO THE REPLACEMENT OF VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.
TSBELE0892017-02-17. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). TSB: NAVIGATION HEAD UNIT SD CARD REPLACEMENT - THIS BULLETIN DESCRIBES THE SD CARD EXCHANGE/REPLACEMENT PROCEDURE RELATED TO ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.
TSB ENG148_REV12017-02-16. Service bulletin. ENGINE. THIS BULLETIN PROVIDES INFORMATION ABOUT THE TIMING CHAIN TENSIONER REPLACEMENT ON SOME 2014-2016 MY CADENZA VEHICLES PRODUCED FROM SOP THROUGH JANUARY 7, 2016, WHICH MAY EXPERIENCE A BRIEF CHATTERING OR RATTLING NOISE CONCERN FROM THE ENGINE AT START-UP AFTER A COLD SOAK. AFTER CONFIRMING THE NOISE CONCERN, FOLLOW THE PROCEDURES OUTLINED IN THE TSB TO RESOLVE THE CONCERN.
PS4652017-02-08. Service bulletin. EQUIPMENT; LANE DEPARTURE: BLIND SPOT DETECTION; ELECTRICAL SYSTEM. PITSTOP: RECALIBRATION OF BLIND SPOT DETECTION AFTER COLLISION REPAIRS - THIS PITSTOP PROVIDES INFORMATION RELATING TO SOME VEHICLES EQUIPPED WITH BLIND SPOT DETECTION (BSD), WHICH MAY EXHIBIT A “CHECK BSD SYSTEM” MESSAGE WITH DTCS: C270254 AND C270354: C270254: CONTROL MODULE MASTER MISSING CALIBRATION / C270354: CONTROL MODULE SLAVE MISSING CALIBRATION
PS266R12017-02-08. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. PITSTOP: HVAC RECEIVER/DRYER - DESICCANT REPLACEMENT - IN THE EVENT OF A HVAC SYSTEM CONCERN IN WHICH METAL PARTICLES OR SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.
TSBCHA074R12017-02-08. Service bulletin. STEERING. TSB REV1: MDPS FLEXIBLE COUPLING REPLACEMENT - THIS BULLETIN IS ISSUED TO PROVIDE INFORMATION ABOUT THE REPLACEMENT OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR OF SOME VEHICLES WHICH MIGHT EXPERIENCE A “KNOCK” NOISE ORIGINATING FROM THE MDPS, WHEN MOVING THE STEERING WHEEL TO RIGHT OR LEFT WHEN THE VEHICLE IS STOPPED. THIS IS CAUSED BY PREMATURE WEAR OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR. IF ANY “KNOCK” NOISE FROM THE MDPS OCCURS, REPLACE THE AFFECTED FLEXIBLE COUPLING ONLY WITH AN IMPROVED ONE, FOLLOWING THE REPLACEMENT PROCEDURE BELOW.
TSBENG148R42017-02-07. Service bulletin. ENGINE. TSB REV4: CHATTER/RATTLE NOISE FROM ENGINE AFTER COLD SOAK - THIS BULLETIN PROVIDES INFORMATION ABOUT THE TIMING CHAIN TENSIONER REPLACEMENT ON SOME 2014~16MY CADENZA (VG), PRODUCED FROM FEBRUARY 1, 2013 THROUGH JANUARY 7, 2016, AND SOME 2014~2015MY SORENTO (XMA) VEHICLES, PRODUCED FROM DECEMBER 17, 2012 THROUGH DECEMBER 11, 2014, WHICH MAY EXPERIENCE A BRIEF CHATTERING OR RATTLING NOISE CONCERN FROM THE ENGINE ON START-UP, AFTER A COLD SOAK. AFTER CONFIRMING THE NOISE CONCERN, FOLLOW THE PROCEDURES OUTLINED IN THIS TSB TO RESOLVE THE CONCERN.
PS2732017-02-06. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. PITSTOP: AVN HEAD-UNIT AND/OR MONITOR REPLACEMENT - WHEN PERFORMING A REPLACEMENT OF THE AVN HEAD UNIT OR MONITOR ON CADENZA VEHICLES, MAKE SURE TO DISCONNECT THE NEGATIVE (-) TERMINAL FROM THE BATTERY BEFORE CONDUCTING ANY REPAIRS. ALL POWER SHOULD BE DISCONTINUED TO THE AVN MONITOR WHEN UNPLUGGED FROM THE AVN HEAD UNIT.
PS4002017-01-31. Service bulletin. VEHICLE SPEED CONTROL; ENGINE. PITSTOP: SMART PEDAL FEATURE - THE “SMART PEDAL” IS AN INTEGRAL PART OF THE ENGINE MANAGEMENT SYSTEM (EMS) FUNCTIONALITY WHICH MONITORS AND PREVENTS THE SIMULTANEOUS ACTIVATION OF ACCELERATOR AND BRAKE PEDALS. WHEN ENGAGED, THE FEATURE REDUCES ENGINE POWER TO IDLE. MOST CUSTOMERS WILL NEVER NOTICE THE SMART PEDAL FEATURE WHEN ACTIVE, HOWEVER, CUSTOMERS WHO TEND TO REST THEIR FOOT ON THE BRAKE PEDAL WHILE DRIVING MIGHT DESCRIBE A HESITATION OR DELAY SYMPTOM AND NOT REALIZE THAT THE EMS ELECTRONIC CONTROL MODULE IS INTERVENING, AS DESIGNED.
TSBTRA051R12017-01-27. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). TSB: 6 SPD A/T SOLENOID REPLACEMENT – MULTIPLE DTCS - THIS BULLETIN PROVIDES INFORMATION RELATING TO THE REPLACEMENT OF VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.
TSBELE0892017-01-27. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). TSB: NAVIGATION HEAD UNIT SD CARD REPLACEMENT - THIS BULLETIN DESCRIBES THE SD CARD EXCHANGE/REPLACEMENT PROCEDURE RELATED TO ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.
PS4172017-01-26. Service bulletin. ENGINE. PITSTOP: DTC P0315 - CRANKSHAFT POSITION (CKP) SENSOR VARIATION NOT LEARNED - WHEN ENCOUNTERING A CUSTOMER COMPLAINT OF ENGINE MISFIRE WITH A MALFUNCTION INDICATOR LIGHT (MIL) ON IN THE DASH, CHECK FOR THE PRESENCE OF DTC P0315 – CRANKSHAFT POSITION SENSOR (CKP) VARIATION NOT LEARNED. USE THE VMI TO VIEW THE SCOPE PATTERN OF THE CRANKSHAFT POSITION SENSOR SIGNAL. VERIFY A GOOD EQUAL CRANKSHAFT SENSOR PATTERN IS PRESENT WITH NO DIPS OR VARIATION, AS SHOWN IN FIGURE A, IN THE SIGN WAVE PATTERN. IF THE PATTERN IS IDENTICAL TO FIGURE A, USE GDS/KDS TO PERFORM A CRANK SENSOR RELEARN PROCEDURE. IF THE PATTERN SHOWS A DIP OR VARIATION, AS SHOWN IN FIGURE B, REPLACE THE FLEX PLATE TO RESOLVE THE CONCERN.
TSBELE0902017-01-26. Service bulletin. ELECTRICAL SYSTEM. TSB: “C” STATE ERROR MESSAGE ON VERSION 8.5 MAP UPDATE - THIS BULLETIN DESCRIBES AN SD CARD REPLACEMENT PROCEDURE FOR CUSTOMERS THAT HAVE A SPECIFIC ERROR DISPLAYED ON THE NAVIGATION HEAD UNIT (SHOWN BELOW) AFTER PURCHASING AND INSTALLING A VERSION 8.5 MAP UPDATE SD CARD. A TOTAL OF 129 AFFECTED SD CARDS WERE PURCHASED BY CUSTOMERS THROUGH KIA DEALERS, FROM JANUARY 1ST TO MAY 11TH, 2015.
TSBCHA0742017-01-26. Service bulletin. STEERING. TSB: MDPS FLEXIBLE COUPLING REPLACEMENT - THIS BULLETIN IS ISSUED TO PROVIDE INFORMATION ABOUT THE REPLACEMENT OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR OF SOME VEHICLES WHICH MIGHT EXPERIENCE A “KNOCK” NOISE ORIGINATING FROM THE MDPS, WHEN MOVING THE STEERING WHEEL TO RIGHT OR LEFT WHEN THE VEHICLE IS STOPPED. THIS IS CAUSED BY PREMATURE WEAR OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR. IF ANY “KNOCK” NOISE FROM THE MDPS OCCURS, REPLACE THE AFFECTED FLEXIBLE COUPLING ONLY WITH AN IMPROVED ONE, FOLLOWING THE REPLACEMENT PROCEDURE BELOW.
TSBENG148R32017-01-26. Service bulletin. ENGINE. TSB: CHATTER/RATTLE NOISE FROM ENGINE AFTER COLD SOAK - THIS BULLETIN PROVIDES INFORMATION ABOUT THE TIMING CHAIN TENSIONER REPLACEMENT ON SOME 2014~16MY CADENZA (VG), PRODUCED FROM FEBRUARY 1, 2013 THROUGH JANUARY 7, 2016, AND SOME 2014~2015MY SORENTO (XMA) VEHICLES, PRODUCED FROM DECEMBER 17, 2012 THROUGH DECEMBER 11, 2014, WHICH MAY EXPERIENCE A BRIEF CHATTERING OR RATTLING NOISE CONCERN FROM THE ENGINE ON START-UP, AFTER A COLD SOAK. AFTER CONFIRMING THE NOISE CONCERN, FOLLOW THE PROCEDURES OUTLINED IN THIS TSB TO RESOLVE THE CONCERN.
TSBENG148R12017-01-25. Service bulletin. ENGINE. TSB: CHATTER/RATTLE NOISE FROM ENGINE AFTER COLD SOAK - THIS BULLETIN PROVIDES INFORMATION ABOUT THE TIMING CHAIN TENSIONER REPLACEMENT ON SOME 2014~16MY CADENZA (VG) VEHICLES, PRODUCED FROM SOP THROUGH JANUARY 7, 2016, WHICH MAY EXPERIENCE A BRIEF CHATTERING OR RATTLING NOISE CONCERN FROM THE ENGINE ON START-UP, AFTER A COLD SOAK. AFTER CONFIRMING THE NOISE CONCERN, FOLLOW THE PROCEDURES OUTLINED IN THIS TSB TO RESOLVE THE CONCERN.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.