Service bulletins for the 2024 Jeep Wrangler
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
495 on file from NHTSA, as of 2026-10-19.
About P0058 on the 2024 Jeep Wrangler: what the code means, and the bulletins and recalls about the same components.
By type
By component
By trouble code
Only bulletins with trouble code: P0058 are shown. Show all
| 18-003-26 REV A | 2026-04-22. Service bulletin. ENGINE; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst heating).** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. (Manual Transmission Only) ● P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0152-02 - O2 Sensor 2/1 Circuit High. ● P0158-02 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - Battery/System Voltage High. Customers may also comment on one or more of the following: ● **The vehicle has a rough idle. ● The engine has a miss or runs rough. ● Noisy valvetrain. M18 FSAR-TSB-7163 -2- ● "Service Transmission" message in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutra |
|---|---|
| 18-003-26 | 2026-01-28. Service bulletin. ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. **(Manual Transmission Only)** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on the following: ● "Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection **(Manual Transmission Only). NOTE: Customers might experience wheel spin or slippage and the PCM could interpreted the wheel spin or slippage as slipping the clutch too much and to avoid clutch damage, the customer may see the message in the IPC.** ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear) **(Manual Transmission Only)**. ● Vehicle runs rough. Other software enhancements include: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 heater crack improvements. ● OBD software changes. statement. Revisions not highlighted by asterisks include removal of a Sale Code. M18 FSAR-TSB-6879 -2- This Technical Service Bulletin (TSB) has also been released as a Rapid Service Update (RSU) 24-109, date of issue August 01, 2024. All applicable RSU VINs have been loaded. To verify this RSU service action is applicable to the vehicle, use VIP or perform a VIN search in DealerCONNECT/Service Library. All repairs are reimbursable within the provisions of warranty. REPAIR SUMMARY: **This bulletin involves inspecting and possibly reprogramming the PCM with th |
| 18-008-25 REV. A | 2025-07-17. Service bulletin. UNKNOWN OR OTHER. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation.** ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● "Service Transmission” message on in the Instrument Panel Cluster (IPC). ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other software enhancements included: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 heater crack improvements. ● OBD software changes. This bulletin involves reprogramming the PCM with the latest available software. |
| 18-008-25 | 2025-03-04. Service bulletin. ENGINE; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates "Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other software enhancements included: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 heater crack improvements. ● OBD software changes. This bulletin involves reprogramming the PCM with the latest available software" |
| 18-050-24 REV. B | 2024-09-10. Service bulletin. POWER TRAIN. "Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other software enhancements included: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 heater crack improvements. ● OBD software changes. This bulletin involves reprogramming the PCM with the latest available software. " |
| 18-065-24 | 2024-08-06. Service bulletin. POWER TRAIN. "Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High. This bulletin involves reprogramming the PCM with the latest available software and possibly replacing one or more oxygen sensors." |
| 18-050-24 REV. A | 2024-08-06. Service bulletin. POWER TRAIN. "Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0032 - O2 - Sensor 1/1 Heater Circuit High. ● P0038 - O2 - Sensor 1/2 Heater Circuit High. ● P0052 - O2 - Sensor 2/1 Heater Circuit High. ● P0058 - O2 - Sensor 2/2 Heater Circuit High.** ● P1129 - Closed Loop Fueling Not Achieved-Banks 2 Upstream. ● P0152 - O2 Sensor 2/1 Circuit High. ● P0158 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - System Voltage High. Customers may also comment on one or more of the following: ● Vehicle runs rough. ● ""Service Transmission” message on in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. ● During flat tow - Transfer case mis-shift (engine running and clutch pedal up, transmission in gear). Other software enhancements included: ● Improvements to address vehicle no starts after replacing the PCM. ● O2 Heater crack improvements. ● OBD Software changes. This bulletin involves reprogramming the PCM with the latest available software. " |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.