WenmarOpen by Wenmar Pro

Service bulletins for the 2023 Jeep Wrangler

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

527 on file from NHTSA, as of 2026-10-19.

About P0300 on the 2023 Jeep Wrangler: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: P0300 are shown. Show all

Bulletins, newest first
18-048-262026-04-22. Service bulletin. POWER TRAIN; ENGINE. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst heating). Customers may also comment on one or more of the following: ● The vehicle has a rough idle. ● The engine has a miss. ● Noisy valvetrain. This bulletin involves reprogramming the PCM with the latest available software.
18-046-262026-04-22. Service bulletin. ENGINE; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0300 - Multiple Cylinder Misfire (Active or Stored status set during cold start catalyst heating). ● P0301 - Cylinder 1 Misfire (Active or Stored status set during cold start catalyst heating). ● P0302 - Cylinder 2 Misfire (Active or Stored status set during cold start catalyst heating). ● P0303 - Cylinder 3 Misfire (Active or Stored status set during cold start catalyst heating). ● P0304 - Cylinder 4 Misfire (Active or Stored status set during cold start catalyst heating). ● P0305-00 - Cylinder 5 Misfire (Active or Stored status set during cold start catalyst heating). ● P0306-00 - Cylinder 6 Misfire (Active or Stored status set during cold start catalyst heating).** ● P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. ● P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. ● P1129 - Closed Loop Fueling Not Achieved - Bank 2 Upstream. ● P0152-02 - O2 Sensor 2/1 Circuit High. ● P0158-02 - O2 Sensor 2/2 Circuit High. ● P2504 - Charging System Output High. ● P0563 - Battery/System Voltage High. Customers may also comment on one or more of the following: ● **The vehicle has a rough idle. ● The engine has a miss. ● Noisy valvetrain. ● "Service Transmission" message in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. NOTE: Some customers may experience wheel spin or traction loss. In these situations, the Powertrain Control Module (PCM) may interpret the event as excessive clutch slip. To prevent potential clutch damage, a message may be displayed in the Instrument Panel Cluster (IPC).** ● Clutch is overheating. ● Clutch is slipping on engagement. ● Inability to accelerate uphill. M18 FSAR-TSB-7162 -2- ● Vehicle does not start. ● Vehicle is stuck in limp-home mode
91001432023-07-31. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. PSU right intake camshaft Case 1) If you are to flash the PSU (Pentastar Upgrade Engine) PCM due to P0300 code presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).
18052232023-05-30. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P016F - Closed Loop Fuel Pressure Control At Limit - Pressure Too Low. ? P025C - Fuel Pump Module Control Circuit Low. ? P0300-00 - Multiple Cylinder Misfire. ? P0301-00 - Cylinder 1 Misfire. ? P0302-00 - Cylinder 2 Misfire. ? P0303-00 - Cylinder 3 Misfire. ? P0304-00 - Cylinder 4 Misfire. ? P0305-00 - Cylinder 5 Misfire. ? P0403-00 - EGR Control Circuit Open (Disabled Fault). ? P208B - Reductant Pump 1 Control Performance. Other Software enhancements: ? Low speed engine idle improvements. ? Improved engine restart performance and torque response during low fuel level and/or hot ambient conditions. This bulletin involves reprogramming the PCM with the latest available software.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.