Service bulletins for the 2024 Jeep Compass
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
314 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Body and frame are shown. Show all
| 08-182-24 | 2024-08-19. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY. "Tail Lamp Condensation Customers may experience one or more of the following: ● Foggy appearance in body side tail lamp (M6 & H6). ● Foggy appearance in exterior lamp bar (H6). This bulletin involves inspecting and possibly replacing the body side tail lamp and/or the exterior lamp bar." |
|---|---|
| 23-004-24 REV. A | 2024-08-13. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM. "Headlamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior head lamp assemblies are fogged with a light layer of condensation on the inside of the lenses." |
| 9100398 | 2024-08-01. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY. SWITCH Power Window Before replacing the master window switch (Driver door window switch), please follow these steps: 1.- Review the master window Switch for any physical issue (Button stuck, broke). If not, physical issue is found move to next step 2.- Review window switch internal resistors, and make sure it matches the continuity chart found on service info of the switch. (649 +/- 7 Ohms when pushing UP, 2519 +/- 25 Ohms when pushing down) If an issue is found with the internal resistor or on the physical parts of the switch, please replace the switch. |
| 31-001-24 | 2024-07-30. Service bulletin. STRUCTURE:BODY. "Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels." |
| 08-153-24 | 2024-07-02. Service bulletin. STRUCTURE:BODY. "Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing." |
| 0822723 | 2024-01-16. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE; ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM. Flash: Body Control Module (BCM) Updates Customers may experience the following: ? Autofolding mirrors inoperative This bulletin involves reprogramming the BCM module with the latest available software. |
| 0827723 | 2023-12-18. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM. Flash: Body Control Module (BCM) Updates Customers may experience the following: ? Autofolding mirrors inoperative This bulletin involves reprogramming the BCM module with the latest available software. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.