WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Jeep Compass

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

371 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
91007762026-03-13. Service bulletin. POWER TRAIN. Before replacing the RDM, please be aware that NVH from differential gears is typical and within the acceptable limits. Do not replace RDM for NVH issue.
21-040-252025-10-08. Service bulletin. POWER TRAIN. 948TE Transmission Reaction Shaft Service Bushing Kit Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1DB7-00 - Torque Converter Clutch Performance.
18019232024-01-02. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P06E9 - Engine Starter Performance (NA Only). ? P0456 - EVAP System Small Leak. NOTE: If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. ? P141B - Starter Control 1 Circuit Performance. ? P141C - Starter Control 2 Circuit Performance. ? P26E4-64 - Starter Control 2 Circuit Signal Plausibility Failure. ? P0615-64 - Starter Control Circuit Signal Plausibility Failure. In addition, the customer may notice one or more of the following conditions: ? **A difference in the set cruise control speed and actual speed on the odometer (i.e. driver sets 100 kph (62 mph), vehicle will hit a max of 95 kph (59 mph) and cruise at 95 kph (59 mph)) (Sales Code ED6 Only).** ? Long engine cranking prior to vehicle start, more noticeable when the outside temperature is above 40 °c (104 °f) (EE with Sales Code ED6 Only). ? Vehicle will intermittently not start (South Korea Only). ? Poor fuel economy. ? Slight engine pinging noise while accelerating and poor performance. ? The engine oil dipstick may indicate a low oil level, however the low oil pressure warning indicator does not illuminate in the Instrument Panel Cluster (IPC). ? No crank condition while pushing the start button numerous times, if the vehicle is turned off completely and then restarted, it will start normally. ? Cruise control and adaptive cruise control are inoperable. ? A ?Service Speed Limiter? message in the IPC and Active Vehicle Speed Limiter (AVSL) will be inoperable. NOTE: There will be no stored or active DTCs with this IPC message. This bulletin involves reprogramming the PCM with the latest available software.
18019232023-04-17. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P06E9 - Engine Starter Performance (NA Only). ? P0456 - EVAP System Small Leak. NOTE: If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. ? P141B - Starter Control 1 Circuit Performance. ? P141C - Starter Control 2 Circuit Performance. ? P26E4-64 - Starter Control 2 Circuit Signal Plausibility Failure. ? P0615-64 - Starter Control Circuit Signal Plausibility Failure. In addition, the customer may notice one or more of the following conditions: ? **A difference in the set cruise control speed and actual speed on the odometer (i.e. driver sets 100 kph (62 mph), vehicle will hit a max of 95 kph (59 mph) and cruise at 95 kph (59 mph)) (Sales Code ED6 Only).** ? Long engine cranking prior to vehicle start, more noticeable when the outside temperature is above 40 °c (104 °f) (EE with Sales Code ED6 Only). ? Vehicle will intermittently not start (South Korea Only). ? Poor fuel economy. ? Slight engine pinging noise while accelerating and poor performance. ? The engine oil dipstick may indicate a low oil level, however the low oil pressure warning indicator does not illuminate in the Instrument Panel Cluster (IPC). ? No crank condition while pushing the start button numerous times, if the vehicle is turned off completely and then restarted, it will start normally. ? Cruise control and adaptive cruise control are inoperable. ? A ?Service Speed Limiter? message in the IPC and Active Vehicle Speed Limiter (AVSL) will be inoperable. NOTE: There will be no stored or active DTCs with this IPC message. This bulletin involves reprogramming the PCM with the latest available software.
21039202023-01-09. Service bulletin. FUEL SYSTEM, GASOLINE; POWER TRAIN; WHEELS. Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
S20210000042023-01-09. Service bulletin. POWER TRAIN; STRUCTURE. Valve Body Learn Procedure On WiTech Shows The Transmission Is Not In The Proper Gear After Repairs
18081222022-12-19. Service bulletin. EXTERIOR LIGHTING; PARKING BRAKE; ELECTRICAL SYSTEM; POWER TRAIN; BACK OVER PREVENTION; LANE DEPARTURE; SERVICE BRAKES, HYDRAULIC. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set: P06E9 - Engine Starter Performance (North America Only). P0456 - EVAP System Small Leak. If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P141B - Starter Control 1 Circuit Performance. P141C - Starter Control 2 Circuit Performance. P26E4-64 - Starter Control 2 Circuit-Signal Plausibility Failure. P0615-64 - Starter Control Circuit-Signal Plausibility Failure. In addition, the customer may notice one or more of the following conditions:Long engine cranking prior to vehicle start more noticeable when the outside temperature is above 40°c (104°f)(EMEA with Sales Code ED6 only). Vehicle will intermittently not start(South Korea Only). Poor fuel economy. Slight engine pinging noise while accelerating and poor performance. Engine may stall while idling. The engine oil dipstick may indicate a low oil level, however the low oil pressure warning indicator doesnotilluminate in the Instrument Panel Cluster (IPC). No crank condition while pushing the start button numerous times, if they turn the vehicle off completely and then retry it will start normally. Cruise control and adaptive cruise control are inoperable. A ?Service Speed Limiter? message in the IPC and Active Vehicle Speed Limiter (AVSL) will be inoperable. There will be no stored or active DTCs with this IPC message.
S19080001022022-10-17. Service bulletin. POWER TRAIN. (Rev. A) Power Inverter Load Ratings
S20180000082022-10-17. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Engine Surge Feel and/or Diagnostic Trouble Code P0299 ? Turbo Underboost Condition After Updating The Powertrain Control Module (PCM) Software. (ETL, ETM, ETN Engines)
S17210000162022-10-17. Service bulletin. POWER TRAIN. Service 4wd Light On, Message AWD System Service Required
S22080000732022-10-17. Service bulletin. POWER TRAIN. No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
90044532022-10-17. Service bulletin. STRUCTURE; POWER TRAIN; BACK OVER PREVENTION; STEERING; WHEELS. GEAR, Rack and Pinion If looking to replace the rack and pinion due to a clunking / knocking noise, please use the Chassis Ear Tool to pinpoint the exact location of the noise following the proper diagnostics. The points where you should place the chassis ear tool in sequence are: steering column, rack and pinion, intermediate shaft or the outer tie rod of the rack and pinion. Also ensure all related components are properly torqued such as shock absorbers, steering column, lower ball joints, stabilizer links, sway bar links and cradle mount bolts (front and rear). Please contact FCA Redacted Content for feedback related ONLY to this GPOP Tech Tip. Do Not email regarding repair procedures unrelated to this Tech Tip or part order inquiries.
21039202022-09-26. Service bulletin. POWER TRAIN. Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.
S20210000042022-09-26. Service bulletin. POWER TRAIN. Valve Body Learn Procedure On WiTech Shows The Transmission Is Not In The Proper Gear After Repairs
25003212022-09-26. Service bulletin. ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM; ELECTRICAL SYSTEM:SOFTWARE; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS; FUEL SYSTEM, GASOLINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EXTERIOR LIGHTING. Flash: Dosing Control Unit (DCU) Updates This bulletin involves reprogramming the Dosing Control Unit (DCU) with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) or symptom/condition.P20F6-00 - Reductant Injection Valve Stuck Open Bank 1 Unit 1. P208E-00 - Reductant Injector Stuck Closed - Bank 1 Unit 1.
S18210000012022-09-26. Service bulletin. POWER TRAIN. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
18033212022-09-26. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customer may also experience the following:Engine hesitation/surge feeling between 40 - 80 kph (25 - 50 mph) on acceleration but is not felt between 3500 - 4000 rpm. (MP only) Engine hesitation/surge feeling after a cold engine start and while driving in 2nd gear under 3000 rpm (customer may comment that the engine doesn't give full power until after a couple minutes).
21040192022-09-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Transmission Control Module (TCM) Updates - AN-M4/1.3T-18-20191023 Refer to China Joint Venture (JV) released document AN-M4/1.3T-18-20191023 for details on this service action.
18035192022-09-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P06E9 - Engine Starter Performance (North America Only). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P141B - Starter Control 1 Circuit Performance. P141C - Starter Control 2 Circuit Performance. P26E4-64 - Starter Control 2 Circuit-Signal Plausibility Failure. P0615-64 - Starter Control Circuit-Signal Plausibility Failure. In addition, the customer may notice one or more of the following conditions:Vehicle will intermittently not start(South Korea Only). Poor fuel economy. Slight engine pinging noise while accelerating and poor performance. Engine may stall while idling. The engine oil dipstick may indicate a low oil level, however the low oil pressure warning indicator doesnotilluminate in the Instrument Panel Cluster (IPC). No crank condition while pushing the start button numerous times, if they turn the vehicle off completely and then retry it will start normally. Cruise control and adaptive cruise control are inoperable. A ?Service Speed Limiter? message in the IPC and Active Vehicle Speed Limiter (AVSL) will be inoperable.There will be no stored or active DTCs with this IPC message.
S21030000012022-09-15. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION; POWER TRAIN. Ratcheting Or Growling Noise From Rear Differential Module (RDM).
S21030000012022-08-22. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT. Ratcheting Or Growling Noise From Rear Differential Module (RDM).
08-068-212021-05-24. Service bulletin. POWER TRAIN; EXTERIOR LIGHTING; FUEL SYSTEM, DIESEL; FUEL SYSTEM, GASOLINE; VEHICLE SPEED CONTROL; BACK OVER PREVENTION; PARKING BRAKE; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; STRUCTURE; WHEELS; AIR BAGS. Flash: Body Control Module (BCM) Updates This bulletin involves reprogramming the BCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set: P0563-00 - System Voltage High(2020 M6 Vehicles equipped with 2.0L I4 Turbo Diesel Engine W/ESS (Sales Code EBS only)). P21CC?00 - Reductant Control Module Supply Voltage High(2020 M6 Vehicles equipped with (Sales Code EBS only)). P1515-00 - Plausibility Check R1 Stuck Closed Or Vsensing Short To Battery In Engine Running(2019 M6 only). B25C9 - Driver Door Ajar Switch 2 Stuck Closed (Module, Powertrain Control (PCM)). Stored DTC only, this update isnotfor active fault.If B25C9 is an active fault normal diagnostic must be performed. This software update will not correct active DTC. P26E4-64 - Starter Control 2 Circuit-Signal Plausibility Failure. In addition, customers or technicians may comment on one or more of the following:Engine Stop/Start (ESS) not functioning properly(2020 M6 Vehicles equipped with (Sales Code EBS only). Four wheel drive not functioning(2020 M6 Vehicles equipped with (Sales Code EBS only). No start condition if the vehicle has both P1515-00 and P26E4-64 DTCs(2019 M6 only). Park assist LED does not turn on(2019-20 MP/M1 and 2019 M6 only). The key fob does not work for power lift gate (Sales Code JRC)(2019-20 MP/M1 and 2019 M6 only). Vehicle Theft Alarm (VTA) sounding after remote start time out(2019-20 MP/M1 and 2019 M6 only). VTA triggers randomly. The vehicle will not restart when in Engine Stop/Start (ESS) mode. Customers will have to shift into park and cycle the ignition to get the vehicle to start again. The vehicle cranks but fails to start, the customer will see a message on the Instrument Panel Cluster (IPC) "press brake and push ignition button to start" after this happens they must perform a key cycle
18-033-212021-04-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customer may also experience the following:Engine hesitation/surge feeling between 40 - 80 kph (25 - 50 mph) on acceleration but is not felt between 3500 - 4000 rpm. (MP only) Engine hesitation/surge feeling after a cold engine start and while driving in 2nd gear under 3000 rpm (customer may comment that the engine doesn't give full power until after a couple minutes).
21-049-202020-10-26. Service bulletin. POWER TRAIN. Flash: Transmission Control Module (TCM) Updates - AN-M4-18-20200825 Refer to China Joint Venture (JV) released document AN-M4-18-20200825 for details on this service action.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.