WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Jeep Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

407 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
W202022-09-26. Service bulletin. POWER TRAIN. Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
S18210000012022-09-26. Service bulletin. POWER TRAIN. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
18023192022-09-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance Plausibility.
18024192022-09-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. Customers may also comment on one or more of the following:Extended engine crank times or possibly a no start condition(South Korea with Sales Code EDD only). The engine fails to restart while in Engine Stop/Start (ESS) mode. This is usually accompanied withDTC P06EF.
90041742022-09-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. HANDS FREE ASSEMBLY, Power Liftgate For a concern of intermittent operation of the liftgate kick sensor, replacing this part with another AA level part will not resolve the concern. When the vehicle is in sleep mode (key off for more than 15 minutes) and an improper kick is detected, the module fails to send a signal for subsequent good kicks but is resolved with a key cycle. Engineering is working on a solution ETA Feb 2020. Do not replace with another AA level part for this concern or the issue will persist.
W20 Combo Phase22022-07-18. Service bulletin. POWER TRAIN. Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
S2008000113 Rev.2021-05-24. Service bulletin. POWER TRAIN. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
18-020-212021-03-15. Service bulletin. POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High.P0607 - ECU Internal Performance.
W20 Combo2021-03-01. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM:SOFTWARE. Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
W20 Combo Phase22021-02-16. Service bulletin. POWER TRAIN. Customer Satisfaction Notification W20 Reprogram Powertrain Control Module
18-063-20 REV. B2020-12-28. Service bulletin. ENGINE; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold Bank 1 Catalyst 1. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. Customers may also describe the following condition: Engine Start/Stop inoperative. Remote start inoperative (South Korea vehicles only). Incorrect vehicle speed reported by the cluster when the driver changes the speed units. Undesirable pedal response in 4-LO mode. Selective Catalytic Reduction (SCR) system fault codes logged at higher vehicle speeds. Alternator load protection at idle. Check Engine Lamp or low battery indicator
18-001-20 REV. B2020-12-28. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates - AN-K4MCA-18-20201001 Refer to China Joint Venture (JV) released document AN-K4MCA-18-20201001, for details on this service action.
S20180000122020-12-28. Service bulletin. ELECTRICAL SYSTEM; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Check engine lamp on. Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.
18-063-20 REV. B2020-12-21. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT ADAPTIVE/MOBILITY. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold Bank 1 Catalyst 1. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. Customers may also describe the following condition:Engine Start/Stop inoperative. Remote start inoperative(South Korea vehicles only). Incorrect vehicle speed reported by the cluster when the driver changes the speed units. Undesirable pedal response in 4-LO mode. Selective Catalytic Reduction (SCR) system fault codes logged at higher vehicle speeds. Alternator load protection at idle. Check Engine Lamp or low battery indicator
18-001-20 REV. B2020-12-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates - AN-K4MCA-18-20201001 Refer to China Joint Venture (JV) released document AN-K4MCA-18-20201001, for details on this service action.
S20180000122020-12-21. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Check engine lamp on. Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.
18-063-20 REV. A2020-11-30. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates The previous release for this PCM software has been removed. Software updates to correct issues will be re-released by the end of 4th quarter 2020.
18-084-20 REV. A2020-11-30. Service bulletin. SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES; ENGINE AND ENGINE COOLING; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P2610 - PCM Internal Engine Off Timer Performance. P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance
18-001-20 REV. A2020-10-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates - AN-K4MCA-18-20200908 Refer to China Joint Venture (JV) released document AN-K4MCA-18-20200908, for details on this service action.
18-084-202020-10-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. C1252 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P06DA - Engine Oil Pressure Control Circuit. P06DD - Engine Oil Pressure Control Circuit Stuck Off. P06DE - Engine Oil Pressure Control Circuit Stuck On. B25C7 - Driver Door Ajar Switch 2 Circuit Low. B25C8 - Driver Door Ajar Switch 2 Circuit High. B25C9 - Driver Door Ajar Switch 2 Stuck Closed. B25CB - Driver Door Ajar Switch 1/Driver Door Ajar Switch 2 Correlation. C10D0 - Electronic Park Brake Module Deactivated. P0EA5 - DC/DC Converter 2 Performance. P0EA6 - DC/DC Converter 2 Over Temperature. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U0128 - Lost Communication With Park Brake Control Module. U0151 - Lost Communication With Occupant Restraint Controller. U0416 - Implausible Data Received From Esp. U0418 - Implausible Data Received From Brake System Control Module 1. U0599 - Invalid Data Received From DC to DC Converter Control Module "A". U0299 - LOC With DC-DC Convertor 2. U1409 - Implausible LF WSS Received. U140A - Implausible RF WSS Received. U059A - Invalid Data Received From DC to DC Converter Control Module "B". C0542 - Brake Pressure Sensor 2 Circuit Low. C0543 - Brake Pressure Sensor 2 Circuit High. P258A - Electric Vacuum Pump Circuit (turn MIL off, switch to 1 trip fault). P0616 - Starter Control Circuit Low. P0617 - Starter Control Circuit High. P0607 - ECU Internal Performance. P3032 - Barometric Pressure Sensor Performance Plausibility.
21-045-202020-10-26. Service bulletin. POWER TRAIN. Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may experience any one of the following: An audible clunk after applying throttle from a coasting condition, predominantly in fifth and sixth gear while driving 48-72 kph (30-45 mph). Poor shift quality or ?bump? experienced during 2-1 coast downs with light brake or no brake applied. Vehicle does not default to automatic drive. Paddle shifters are disabled. "Shift not allowed' displayed in cluster when attempting to upshift while already in 9th gear.
18-063-202020-09-28. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs:P20EE-00 - SCR NOx Catalyst Efficiency Below Threshold Bank 1 Catalyst 1. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. Customers may also describe the following condition:Incorrect vehicle speed reported by the cluster when the driver changes the speed units. Undesirable pedal response in 4-LO mode. Particulate matter (soot) sensor faults codes. Selective Catalytic Reduction (SCR) system fault codes logged at higher vehicle speeds. Alternator load protection at idle. Check Engine Lamp or low battery indicator
18-052-202020-08-24. Service bulletin. POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P04FC - Crankcase Ventilation System Performance. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation(EMEA only equipped with Gas Particulate Filter (GPF))(DTC will set when driving above 72 kph (45 mph). P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P050B - Cold Start Ignition Timing Performance. P258B - Electric Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P2B95 - Cold Start Injection Pulse Performance. P062A - Fuel Pump Control Performance. P058C - Battery Monitor Module Temperature Monitoring Performance. P0607 - ECU Internal Performance. Injector performance faults for cylinders 2 - 4 map to DTC for incorrect cylinders. In addition the following software enhancement are included:Software corrects an issue with the wrong cylinder identification if an injector circuit performance fault is set in the PCM:If any of the series of injector control circuit faults are set, please refer to the bullet-pointed list below to determine which injector to address.For reference, the correct injector circuit performance faults are listed below:P02EE - Cylinder 1 Injector Circuit Performance. P02EF - Cylinder 2 Injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. Customers may also experience the following condition:Audible noise from the Low Temperature Radiator (LTR) coolant pump, at low speeds. Abnormal noise from the radiator cooling fan. LTR runs too long after the engine is turned off.
21-041-202020-08-24. Service bulletin. POWER TRAIN. Transmission Case Oil Leak This bulletin involves tightening the lower transmission bolts to updated torque specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.