WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Jeep Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

257 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
21017212022-10-17. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following: Grinding noise coming from under the vehicle while driving. Vehicle will not move.
18066202022-09-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following DTCs have been set:P1D83 - Implausible Engine Oil Temperature Signal Received. P0556 - Brake Booster Pressure Sensor Circuit Performance. U0428 - Implausible Data Received From Steering Angle Sensor Module. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. C0501 - Left Front Wheel Speed Sensor Range/Performance. C0507 - Right Front Wheel Speed Sensor Range/Performance. C050D - Left Rear Wheel Speed Sensor Range/Performance. C0513 - Right Rear Wheel Speed Sensor Range/Performance. Erroneously set wheel speed sensor DTCs listed above will not turn on the MIL by design but may be found during a vehicle diagnostic scan.Some customers may also experience the following:The engine being too quick to shut down when coming to a stop in Engine Stop/Start (ESS) mode. During an engine limp mode condition, the transmission remains in a fixed gear. In addition, the following software enhancements are available: Calibration update to allow the throttle body to be cycled while the engine is off, for diagnostic purposes. Calibration update for ESS to allow the engine to remain running during a brief stop.
S20080001132022-09-26. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM:IGNITION. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle
90039682022-09-26. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; ELECTRICAL SYSTEM. CONDENSER, Air Conditioning CONDITION 1: If it is determined that the A/C compressor does not engage due to a refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.
W842022-09-26. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Customer Satisfaction Notification W84 Powertrain Software Update
S17230000302022-09-26. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Service Electric Park Brake Message
S21080001632022-09-26. Service bulletin. ELECTRICAL SYSTEM. No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
90043862022-09-26. Service bulletin. ELECTRICAL SYSTEM:WIRING. WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S20080001132022-09-26. Service bulletin. ELECTRICAL SYSTEM. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S16080002262022-09-26. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S160800022612022-09-26. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Battery Tester Warranty Code Procedures, Medtronic Update Process
S17080001182022-09-26. Service bulletin. ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS:ACCESORY POWER OUTLET/JACK/PORT/USB/SAE/CIGARETTE LIGHTER; UNKNOWN OR OTHER. Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
W202022-09-26. Service bulletin. ELECTRICAL SYSTEM. Customer Satisfaction Notification W20 Reprogram Powertrain Control Module (Revision 2)
08111192022-09-15. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. RA3 and RA4 GPS Radio Update This bulletin involves updating the radio software. 18.01.35 (BU Vehicles)
D19252022-09-15. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. RRT 19-090 (Service Bulletin 08-111-19) 2013-2018 Multiple Vehicles RA3/RA4 Radio GPS Certification Error
90038252022-09-15. Service bulletin. SEATS; VEHICLE SPEED CONTROL; ELECTRICAL SYSTEM; AIR BAGS; BACK OVER PREVENTION. LATCH, Hood For the following concerns, please verify secondary plunger switch before replacing hood latch with primary switch. Please refer to service information for complete diagnostics of the secondary plunger switch which is located in the left front under hood on RU, MP, and WK/WD and left rear under hood on KL. 1) Electronic Stop Start Message on Cluster or DTC P152F without hood ajar illuminated. 2) KL Hood ajar light is on or unlatched hood due to high closing effort. (KL hood may have a higher closing effort to latch the hood as rubber bumper interference is set purposely high to prevent hood flutter at highway speeds) If stop start message or DTC P152F is present on vehicles without a hood ajar light illuminated, the issue is not related to the primary hood latch switch.
21-006-17 REV. A2022-09-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P0810-00 - Clutch Position Control Error - (Sales Codes EHK). P0887-00 - TCM Power Control Circuit High. U1424-00 - Implausible Engine Torque Signal Received. P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. Some customers may experience the following conditions:During a limp mode condition, the transmission remains in a fixed gear. 5-4 downshift hesitation. A longer than normal delay during a shift from reverse to drive selection. In addition the following enhancements are included:Calibration update for Engine Stop Start (ESS) to allow the engine to remain running during a brief stop. 2-1 and 3-2 coast down tip-in.
90044012022-08-22. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); ELECTRICAL SYSTEM; SERVICE BRAKES, HYDRAULIC; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. DIFFERENTIAL, Rear Axle (KL 4WD w/DK2 = 1-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The changes are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK2 = 1-spd RDM 2014 - 2015 VINs were built with a 1-speed RDM used a 24 plate clutch design. New service RDMs 68550586A$ use a 20-plate design. 1.1) If replacing the RDM · 24 plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · 68550586A$ service RDMs have a 20 clutch plate design · Not all 20-plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 68550586AA service RDMs is installed, then replace the DLCM with new DLCM 68540647AA - 1-spd designed for the 20-plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540645AA - 1-spd, 24 plate DLCM AND replace the pump with 68551790AA · If the RDM is the new 20 plate design then use 68540647AA - 1-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540645AA for the 24 plate RDM with a new pump. · Use 68540647AA for the 20 plate RDM with a new pump. 2) For 2016 and later VINs with DK2 = 1-spd RDM Early 2016 were built with 68090612AG 24 plate RDMs. Use Section 1 ?For 2014/5 VINs with DK2 = 1-spd RDM? to resolve. The balance of M
90044022022-08-22. Service bulletin. SERVICE BRAKES, HYDRAULIC; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION. DIFFERENTIAL, Rear Axle (KL 4WD w/DK4 = 2-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The chages are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK4 = 2-spd RDM 2014 - 2015 VINs built with a 2-speed RDM used a 24 plate clutch design. Service RDMs (DK4: 68545100AA and DK4 + AWL: 68545101AA) have a 20-plate design. 1.1) If replacing the RDM · 24-plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · Both 68545100A$ and 68545101A$ service RDMs have a 20 clutch plate design · Not all 20 plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 20 plate service RDM is installed, then replace the DLCM with new DLCM 68383660AE - 2-spd designed for the 20 plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540646AA - 2-spd, 24 plate DLCM AND also replace the pump with 68551790AA new pump. · If the RDM is the new 20 plate design then use 68383660AE - 2-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540646AA for the 24-plate RDM with a new pump. · Use 68383660AE for the 20-plate RDM with a new pump. 2) Early 2016 were built with 24 plate RDMs. These include p/n?s 68090615AJ (2spd std), and 52123642AJ (2spd locker). Use Secti
S1708000118 RevB2022-05-31. Service bulletin. ELECTRICAL SYSTEM. Battery Drain Concern, Dual USB Port Normal Operational Draw, Extended Illumination Or Extended Operation After Key Off
21-017-21 Rev. A2021-06-28. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following: Grinding noise coming from under the vehicle while driving. Vehicle will not move.
21-017-212021-06-28. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following:Grinding noise coming from under the vehicle while driving. Vehicle will not move.
745952021-06-28. Service bulletin. ELECTRICAL SYSTEM. Warranty Bulletin D-21-07 (X89) Power Transfer Unit - 2014-2017 Jeep Cherokee (KL)
W20 Combo Phase32021-03-15. Service bulletin. ELECTRICAL SYSTEM. Customer Satisfaction Notification W20 Reprogram Powertrain Control Module (Revision 2)
18-110-202021-03-01. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; STEERING; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following Diagnostic Trouble Codes (DTCs): U1504 - Implausible Message Data Length Received From Steering Angle Sensor. P1185 - General Pressure Sensor Correlation. U1424-00 - Implausible Engine Torque Signal Received. P0101 - Mass Air Flow Sensor "A" Circuit Performance. P0128 - Thermostat Rationality. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition: Extended engine crank times or possibly a no start condition(South Korea only). During an engine limp mode condition, the transmission remains in a fixedgear.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.