Service bulletins for the 2017 Jeep Cherokee
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
257 on file from NHTSA, as of 2026-10-19.
About P0810 on the 2017 Jeep Cherokee: what the code means, and the bulletins and recalls about the same components.
By type
By component
By trouble code
Only bulletins with trouble code: P0810 are shown. Show all
| T52 | 2022-10-31. Service bulletin. EXTERIOR LIGHTING; POWER TRAIN. Customer Satisfaction Notification T52 The vehicle speed on about 24,000 of the above vehicles maybe limited if certain conditions are met. This can occur if the vehicle is brought to a full stop and the gear shifter is immediately moved from ?DRIVE? to ?PARK? and then the key position is changed from ?RUN? to ?ACC?. This action will cause the transmission to be limited to one gear and a maximum speed of 30 ? 45 mph and will illuminate the Malfunction Indicator Lamp (MIL) on the instrument cluster and will set P0810 fault code. Reprogram the transmission control module. |
|---|---|
| 9003714 | 2022-10-17. Service bulletin. UNKNOWN OR OTHER; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:VALVES/VALVE BODY. Transmission, Valve Body If you have a 2017 Cherokee equipped with a 3.2L engine that has set P0810-00 DTC please ensure TCM is updated to the latest level. |
| 21-006-17 REV. A | 2022-09-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P0810-00 - Clutch Position Control Error - (Sales Codes EHK). P0887-00 - TCM Power Control Circuit High. U1424-00 - Implausible Engine Torque Signal Received. P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. Some customers may experience the following conditions:During a limp mode condition, the transmission remains in a fixed gear. 5-4 downshift hesitation. A longer than normal delay during a shift from reverse to drive selection. In addition the following enhancements are included:Calibration update for Engine Stop Start (ESS) to allow the engine to remain running during a brief stop. 2-1 and 3-2 coast down tip-in. |
| 21-006-17 REV. A | 2018-06-04. Service bulletin. POWER TRAIN. Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set:P0810-00 - Clutch Position Control Error - (Sales Codes EHK). P0887-00 - TCM Power Control Circuit High. U1424-00 - Implausible Engine Torque Signal Received. P1DCD-00 - TCM Monitoring Processor Performance Multiple Clutches Locked Up. Some customers may experience the following conditions:During a limp mode condition, the transmission remains in a fixed gear. 5-4 downshift hesitation. A longer than normal delay during a shift from reverse to drive selection. In addition the following enhancements are included:Calibration update for Engine Stop Start (ESS) to allow the engine to remain running during a brief stop. 2-1 and 3-2 coast down tip-in. |
| T52 | 2017-11-03. Service bulletin. POWER TRAIN. Customer Satisfaction Notification T52 Reprogram Transmission ControlModule The vehicle speed on about 24,000 of the above vehicles maybe limited if certain conditions are met. This can occur if the vehicle is brought to a full stop and the gear shifter is immediately moved from ?DRIVE? to ?PARK? and then the key position is changed from ?RUN? to ?ACC?. This action will cause the transmission to be limited to one gear and a maximum speed of 30 ? 45 mph and will illuminate the Malfunction Indicator Lamp (MIL) on the instrument cluster and will set P0810 fault code. Reprogram the transmission control module. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.