Service bulletins for the 2019 Hyundai Santa Fe
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
184 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| 19-AT-024H | 2019-12-16. Service bulletin. ELECTRICAL SYSTEM. If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC. |
|---|---|
| 19-BE-011H-1 | 2019-12-16. Service bulletin. LANE DEPARTURE; BACK OVER PREVENTION. The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving. |
| 19-01-005H-1 | 2019-11-18. Service bulletin. ENGINE; EQUIPMENT. The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. |
| 19-01-006H-4 | 2019-11-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM:WIRING. Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine based on the inspection results. |
| 19-01-002H-4 | 2019-11-18. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE. Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM. |
| Campaign 953 Dea | 2019-11-18. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:SOFTWARE; ENGINE; EQUIPMENT. Hyundai has developed a new engine monitoring technology called a Knock Sensor Detection System (KSDS). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure. |
| Campaign T3G Dea | 2019-11-18. Service bulletin. ENGINE; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L GDI engines that may experience the Check Engine warning lamp illuminated with DTC P132600. |
| 19-BD-008H | 2019-11-18. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. This bulletin provides instructions on the replacement of a cup holder with retaining tabs which cannot stabilize a cup due to inner O-ring displacement. |
| 19-EM-001H | 2019-11-18. Service bulletin. ENGINE. This bulletin provides information regarding the changes in the timing chain and the crankshaft sprockets on certain Azera (HG), Santa Fe/Santa Fe XL (NC), Genesis (BH/DH), Genesis Coupe (BK), and G90 (HI) vehicles equipped with Lambda 3.3L / 3.8L GDI engines. |
| 19-01-005H-1 | 2019-11-06. Service bulletin. ENGINE AND ENGINE COOLING. The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. |
| 19-01-006H-4 | 2019-11-06. Service bulletin. ENGINE AND ENGINE COOLING. Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine based on the inspection results. |
| 19-01-002H-4 | 2019-11-06. Service bulletin. ENGINE AND ENGINE COOLING. Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM. |
| Campaign 953 Dea | 2019-11-06. Service bulletin. ENGINE AND ENGINE COOLING. Hyundai has developed a new engine monitoring technology called a Knock Sensor Detection System (KSDS). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure. |
| Campaign T3G Dea | 2019-11-06. Service bulletin. ENGINE AND ENGINE COOLING. Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L GDI engines that may experience the Check Engine warning lamp illuminated with DTC P132600. |
| 19-BD-008H | 2019-11-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This bulletin provides instructions on the replacement of a cup holder with retaining tabs which cannot stabilize a cup due to inner O-ring displacement. |
| 19-GI-006H | 2019-11-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number. |
| 19-EM-001H | 2019-11-06. Service bulletin. POWER TRAIN. This bulletin provides information regarding the changes in the timing chain and the crankshaft sprockets on certain Azera (HG), Santa Fe/Santa Fe XL (NC), Genesis (BH/DH), Genesis Coupe (BK), and G90 (HI) vehicles equipped with Lambda 3.3L / 3.8L GDI engines. |
| 19-AT-019H | 2019-09-30. Service bulletin. ENGINE; EQUIPMENT; ELECTRICAL SYSTEM. If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related oil pressure harness with integrated oil temperature sensor. |
| 19-AT-018H | 2019-09-30. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related input/output speed sensor and oil pressure harness. |
| 19-AT-017H | 2019-09-30. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID. If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness. |
| 19-BR-001H-1 | 2019-08-19. Service bulletin. SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING. This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly. |
| 19-AT-013H | 2019-08-19. Service bulletin. POWER TRAIN. If you are servicing a 2019 Santa Fe (2.0T) with a harsh 2-3 or 3-4 upshift when cold, follow the Service Procedure below. |
| 19-BR-001H(1) | 2019-07-29. Service bulletin. WHEELS; SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR; SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING. This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly. |
| 19-AT-012H | 2019-07-29. Service bulletin. POWER TRAIN. This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear). |
| 19-BE-008H | 2019-07-01. Service bulletin. ELECTRICAL SYSTEM; LANE DEPARTURE; FORWARD COLLISION AVOIDANCE. This bulletin provides information for replacement of the Blind-Spot Collision Warning (BCW) module. Whenever the left or right side BCW module is being replaced, it is required to perform the variant coding procedure. If the variant coding procedure is not performed, a DTC C1743 (S/W mismatch) will be triggered. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.